.handler = mg_probe_cmd,
.mode = COMMAND_EXEC,
.help = "Detect bank configuration information",
+ .usage = "",
},
{
.name = "write",
.handler = handle_nand_list_command,
.mode = COMMAND_EXEC,
.help = "list configured NAND flash devices",
+ .usage = "",
},
{
.name = "info",
.mode = COMMAND_EXEC,
.help = "Print information about the current at91sam3 chip"
"and its flash configuration.",
+ .usage = "",
},
{
.name = "slowclk",
.mode = COMMAND_EXEC,
.help = "Print information about the current at91sam4 chip"
"and its flash configuration.",
+ .usage = "",
},
{
.name = "slowclk",
.name = "smap_reset_deassert",
.handler = sam4l_handle_reset_deassert,
.mode = COMMAND_EXEC,
- .help = "deasert internal reset held by SMAP"
+ .help = "deassert internal reset held by SMAP",
+ .usage = "",
},
COMMAND_REGISTRATION_DONE
};
.name = "dsu_reset_deassert",
.handler = samd_handle_reset_deassert,
.mode = COMMAND_EXEC,
- .help = "Deasert internal reset held by DSU."
+ .help = "Deassert internal reset held by DSU.",
+ .usage = "",
},
{
.name = "info",
.mode = COMMAND_EXEC,
.help = "Print information about the current at91samd chip "
"and its flash configuration.",
+ .usage = "",
},
{
.name = "chip-erase",
.mode = COMMAND_EXEC,
.help = "Erase the entire Flash by using the Chip-"
"Erase feature in the Device Service Unit (DSU).",
+ .usage = "",
},
{
.name = "set-security",
static const struct command_registration same5_exec_command_handlers[] = {
{
.name = "dsu_reset_deassert",
+ .usage = "",
.handler = samd_handle_reset_deassert,
.mode = COMMAND_EXEC,
.help = "Deasert internal reset held by DSU."
},
{
.name = "chip-erase",
+ .usage = "",
.handler = same5_handle_chip_erase_command,
.mode = COMMAND_EXEC,
.help = "Erase the entire Flash by using the Chip-"
.mode = COMMAND_CONFIG,
.help = "Driver creates additional banks if device with two/four flash blocks is probed",
.handler = kinetis_create_banks_handler,
+ .usage = "",
},
COMMAND_REGISTRATION_DONE
};
.handler = nrf5_handle_mass_erase_command,
.mode = COMMAND_EXEC,
.help = "Erase all flash contents of the chip.",
+ .usage = "",
},
COMMAND_REGISTRATION_DONE
};
.handler = numicro_handle_chip_erase_command,
.mode = COMMAND_EXEC,
.help = "chip erase through ISP.",
+ .usage = "",
},
COMMAND_REGISTRATION_DONE
};
.mode = COMMAND_CONFIG,
.handler = handle_flash_init_command,
.help = "Initialize flash devices.",
+ .usage = "",
},
{
.name = "banks",
.mode = COMMAND_ANY,
.handler = handle_flash_banks_command,
.help = "Display table with information about flash banks.",
+ .usage = "",
},
{
.name = "list",
.handler = handle_meminfo_command,
.mode = COMMAND_ANY,
.help = "display free heap space",
+ .usage = "",
},
#endif
{
.handler = handle_interface_list_command,
.mode = COMMAND_ANY,
.help = "List all built-in debug adapter interfaces (drivers)",
+ .usage = "",
},
{
.name = "reset_config",
.handler = &armjtagew_handle_armjtagew_info_command,
.mode = COMMAND_EXEC,
.help = "query armjtagew info",
+ .usage = "",
},
COMMAND_REGISTRATION_DONE
};
.handler = &buspirate_handle_adc_command,
.mode = COMMAND_EXEC,
.help = "reads voltages on adc pins",
+ .usage = "",
},
{
.name = "buspirate_vreg",
.name = "reset",
.handler = &jlink_handle_config_reset_command,
.mode = COMMAND_EXEC,
- .help = "undo configuration changes"
+ .help = "undo configuration changes",
+ .usage = "",
},
{
.name = "write",
.handler = &jlink_handle_config_write_command,
.mode = COMMAND_EXEC,
- .help = "write configuration to the device"
+ .help = "write configuration to the device",
+ .usage = "",
},
COMMAND_REGISTRATION_DONE
};
.name = "freemem",
.handler = &jlink_handle_free_memory_command,
.mode = COMMAND_EXEC,
- .help = "show free device memory"
+ .help = "show free device memory",
+ .usage = "",
},
{
.name = "hwstatus",
.handler = &jlink_handle_hwstatus_command,
.mode = COMMAND_EXEC,
- .help = "show the hardware status"
+ .help = "show the hardware status",
+ .usage = "",
},
{
.name = "usb",
.handler = &opendous_handle_opendous_info_command,
.mode = COMMAND_EXEC,
.help = "show opendous info",
+ .usage = "",
},
{
.name = "opendous_hw_jtag",
.handler = handle_pld_devices_command,
.mode = COMMAND_EXEC,
.help = "list configured pld devices",
+ .usage = "",
},
{
.name = "load",
.handler = handle_gdb_save_tdesc_command,
.mode = COMMAND_EXEC,
.help = "Save the target description file",
+ .usage = "",
},
COMMAND_REGISTRATION_DONE
};
.mode = COMMAND_CONFIG,
.handler = handle_target_init_command,
.help = "initialize targets",
+ .usage = "",
},
{
.name = "create",
.handler = xscale_handle_cache_info_command,
.mode = COMMAND_EXEC,
.help = "display information about CPU caches",
+ .usage = "",
},
{
.name = "mmu",