tcl/target: Add PSoC 5LP config

[openocd.git] / tcl / target / stm32f4x.cfg

diff --git a/tcl/target/stm32f4x.cfg b/tcl/target/stm32f4x.cfg
index a7ec5eab3e18e5f59c3724c42520ed614cd933a9..7205c461486e4f152348a8bceb21dc6afa40a120 100644 (file)
--- a/tcl/target/stm32f4x.cfg
+++ b/tcl/target/stm32f4x.cfg
@@ -4,6 +4,7 @@
 # stm32 devices support both JTAG and SWD transports.
 #
 source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
@@ -11,11 +12,7 @@ if { [info exists CHIPNAME] } {
    set _CHIPNAME stm32f4x
 }
 
-if { [info exists ENDIAN] } {
-   set _ENDIAN $ENDIAN
-} else {
-   set _ENDIAN little
-}
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
 # By default use 64kB
@@ -86,8 +83,45 @@ if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
 
+reset_config srst_nogate
+
 if {![using_hla]} {
    # if srst is not fitted use SYSRESETREQ to
    # perform a soft reset
    cortex_m reset_config sysresetreq
 }
+
+$_TARGETNAME configure -event examine-end {
+       # Enable debug during low power modes (uses more power)
+       # DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
+       mmw 0xE0042004 0x00000007 0
+
+       # Stop watchdog counters during halt
+       # DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
+       mmw 0xE0042008 0x00001800 0
+}
+
+$_TARGETNAME configure -event trace-config {
+       # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
+       # change this value accordingly to configure trace pins
+       # assignment
+       mmw 0xE0042004 0x00000020 0
+}
+
+$_TARGETNAME configure -event reset-init {
+       # Configure PLL to boost clock to HSI x 4 (64 MHz)
+       mww 0x40023804 0x08012008   ;# RCC_PLLCFGR 16 Mhz /8 (M) * 128 (N) /4(P)
+       mww 0x40023C00 0x00000102   ;# FLASH_ACR = PRFTBE | 2(Latency)
+       mmw 0x40023800 0x01000000 0 ;# RCC_CR |= PLLON
+       sleep 10                    ;# Wait for PLL to lock
+       mmw 0x40023808 0x00001000 0 ;# RCC_CFGR |= RCC_CFGR_PPRE1_DIV2
+       mmw 0x40023808 0x00000002 0 ;# RCC_CFGR |= RCC_CFGR_SW_PLL
+
+       # Boost JTAG frequency
+       adapter_khz 8000
+}
+
+$_TARGETNAME configure -event reset-start {
+       # Reduce speed since CPU speed will slow down to 16MHz with the reset
+       adapter_khz 2000
+}