jtag: linuxgpiod: drop extra parenthesis

[openocd.git] / tcl / target / stm32f1x.cfg

diff --git a/tcl/target/stm32f1x.cfg b/tcl/target/stm32f1x.cfg
index 25a6059a0194666187192d3a88531ad77d1baf0d..53e81a59f6b479cb503e7b73ba32bfbe9c685313 100644 (file)
--- a/tcl/target/stm32f1x.cfg
+++ b/tcl/target/stm32f1x.cfg
@@ -1,81 +1,98 @@
-# script for stm32
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+# script for stm32f1x family
+
+#
+# stm32 devices support both JTAG and SWD transports.
+#
+source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
+   set _CHIPNAME $CHIPNAME
 } else {
-   set  _CHIPNAME stm32
+   set _CHIPNAME stm32f1x
 }
 
-if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
-} else {
-   set  _ENDIAN little
-}
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
-# By default use 16kB
+# By default use 4kB (as found on some STM32F100s)
 if { [info exists WORKAREASIZE] } {
-   set  _WORKAREASIZE $WORKAREASIZE
+   set _WORKAREASIZE $WORKAREASIZE
 } else {
-   set  _WORKAREASIZE 0x4000
+   set _WORKAREASIZE 0x1000
 }
 
-# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
-adapter_khz 1000
-
-adapter_nsrst_delay 100
-jtag_ntrst_delay 100
+# Allow overriding the Flash bank size
+if { [info exists FLASH_SIZE] } {
+    set _FLASH_SIZE $FLASH_SIZE
+} else {
+    # autodetect size
+    set _FLASH_SIZE 0
+}
 
 #jtag scan chain
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
-  # See STM Document RM0008
-  # Section 26.6.3
-   set _CPUTAPID 0x3ba00477
+   if { [using_jtag] } {
+      # See STM Document RM0008 Section 26.6.3
+      set _CPUTAPID 0x3ba00477
+   } {
+      # this is the SW-DP tap id not the jtag tap id
+      set _CPUTAPID 0x1ba01477
+   }
 }
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
-if { [info exists BSTAPID ] } {
-   # FIXME this never gets used to override defaults...
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0008
-  # Section 29.6.2
-  # Low density devices, Rev A
-  set _BSTAPID1 0x06412041
-  # Medium density devices, Rev A
-  set _BSTAPID2 0x06410041
-  # Medium density devices, Rev B and Rev Z
-  set _BSTAPID3 0x16410041
-  set _BSTAPID4 0x06420041
-  # High density devices, Rev A
-  set _BSTAPID5 0x06414041
-  # Connectivity line devices, Rev A and Rev Z
-  set _BSTAPID6 0x06418041
-  # XL line devices, Rev A
-  set _BSTAPID7 0x06430041
-  # VL line devices, Rev A and Z In medium-density and high-density value line devices
-  set _BSTAPID8 0x06420041
-  # VL line devices, Rev A
-  set _BSTAPID9 0x06428041
+swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
+if {[using_jtag]} {
+   jtag newtap $_CHIPNAME bs -irlen 5
 }
-jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
-       -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
-       -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 \
-       -expected-id $_BSTAPID6 -expected-id $_BSTAPID7 \
-       -expected-id $_BSTAPID8 -expected-id $_BSTAPID9
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 # flash size will be probed
 set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME stm32f1x 0x08000000 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME stm32f1x 0x08000000 $_FLASH_SIZE 0 0 $_TARGETNAME
+
+# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
+adapter speed 1000
+
+adapter srst delay 100
+if {[using_jtag]} {
+ jtag_ntrst_delay 100
+}
+
+reset_config srst_nogate
+
+if {![using_hla]} {
+    # if srst is not fitted use SYSRESETREQ to
+    # perform a soft reset
+    cortex_m reset_config sysresetreq
+}
+
+$_TARGETNAME configure -event examine-end {
+       # DBGMCU_CR |= DBG_WWDG_STOP | DBG_IWDG_STOP |
+       #              DBG_STANDBY | DBG_STOP | DBG_SLEEP
+       mmw 0xE0042004 0x00000307 0
+}
+
+tpiu create $_CHIPNAME.tpiu -dap $_CHIPNAME.dap -ap-num 0 -baseaddr 0xE0040000
+
+lappend _telnet_autocomplete_skip _proc_pre_enable_$_CHIPNAME.tpiu
+proc _proc_pre_enable_$_CHIPNAME.tpiu {_targetname} {
+       targets $_targetname
+
+       # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
+       # change this value accordingly to configure trace pins
+       # assignment
+       mmw 0xE0042004 0x00000020 0
+}
 
-# if srst is not fitted use SYSRESETREQ to
-# perform a soft reset
-cortex_m3 reset_config sysresetreq
+$_CHIPNAME.tpiu configure -event pre-enable "_proc_pre_enable_$_CHIPNAME.tpiu $_TARGETNAME"