smp: replace commands smp_on/smp_off with "smp [on|off]"

[openocd.git] / tcl / target / stm32f4x.cfg

diff --git a/tcl/target/stm32f4x.cfg b/tcl/target/stm32f4x.cfg
index 7205c461486e4f152348a8bceb21dc6afa40a120..09ce14a5dd50f6af1c218ff91aa295fdda2752ba 100644 (file)
--- a/tcl/target/stm32f4x.cfg
+++ b/tcl/target/stm32f4x.cfg
@@ -15,11 +15,11 @@ if { [info exists CHIPNAME] } {
 set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
-# By default use 64kB
+# By default use 32kB (Available RAM in smallest device STM32F410)
 if { [info exists WORKAREASIZE] } {
    set _WORKAREASIZE $WORKAREASIZE
 } else {
-   set _WORKAREASIZE 0x10000
+   set _WORKAREASIZE 0x8000
 }
 
 #jtag scan chain
@@ -36,40 +36,22 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID] } {
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0090
-  # Section 38.6.2
-  # STM32F405xx/07xx and STM32F415xx/17xx
-  set _BSTAPID1 0x06413041
-  # STM32F42xxx and STM32F43xxx
-  set _BSTAPID2 0x06419041
-  # See STM Document RM0368 (Rev. 3)
-  # STM32F401B/C
-  set _BSTAPID3 0x06423041
-  # STM32F401D/E
-  set _BSTAPID4 0x06433041
-  # See STM Document RM0383 (Rev 2)
-  # STM32F411
-  set _BSTAPID5 0x06431041
-}
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
 if {[using_jtag]} {
- swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
-     -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
-     -expected-id $_BSTAPID4 -expected-id $_BSTAPID5
+   jtag newtap $_CHIPNAME bs -irlen 5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
 
+flash bank $_CHIPNAME.otp stm32f2x 0x1fff7800 0 0 0 $_TARGETNAME
+
 # JTAG speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
 #
 # Since we may be running of an RC oscilator, we crank down the speed a