Support for STM32F722, F723, F413 and F423

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 30d8aaeb4ab32026f2cb848134a8d5fe304ea5b8..89ee5eb45247e438d77bb704bbcf2883901591dd 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -682,7 +682,8 @@ bash$ openocd --help
 --version    | -v       display OpenOCD version
 --file       | -f       use configuration file <name>
 --search     | -s       dir to search for config files and scripts
---debug      | -d       set debug level <0-3>
+--debug      | -d       set debug level to 3
+             | -d<n>    set debug level to <level>
 --log_output | -l       redirect log output to file <name>
 --command    | -c       run <command>
 @end verbatim
@@ -5988,16 +5989,21 @@ The @var{num} parameter is a value shown by @command{flash banks}.
 @end deffn
 
 @deffn Command {stm32f2x options_read} num
-Reads and displays user options and (where implemented) boot_addr0 and boot_addr1.
+Reads and displays user options and (where implemented) boot_addr0, boot_addr1, optcr2.
 The @var{num} parameter is a value shown by @command{flash banks}.
 @end deffn
 
 @deffn Command {stm32f2x options_write} num user_options boot_addr0 boot_addr1
 Writes user options and (where implemented) boot_addr0 and boot_addr1 in raw format.
 Warning: The meaning of the various bits depends on the device, always check datasheet!
-The @var{num} parameter is a value shown by @command{flash banks}, user_options a
-12 bit value, consisting of bits 31-28 and 7-0 of FLASH_OPTCR, boot_addr0 and boot_addr1
-two halfwords (of FLASH_OPTCR1).
+The @var{num} parameter is a value shown by @command{flash banks}, @var{user_options} a
+12 bit value, consisting of bits 31-28 and 7-0 of FLASH_OPTCR, @var{boot_addr0} and
+@var{boot_addr1} two halfwords (of FLASH_OPTCR1).
+@end deffn
+
+@deffn Command {stm32f2x optcr2_write} num optcr2
+Writes FLASH_OPTCR2 options. Warning: Clearing PCROPi bits requires a full mass erase!
+The @var{num} parameter is a value shown by @command{flash banks}, @var{optcr2} a 32-bit word.
 @end deffn
 @end deffn
 
@@ -6849,12 +6855,13 @@ non-zero exit code to the parent process.
 @deffn Command debug_level [n]
 @cindex message level
 Display debug level.
-If @var{n} (from 0..3) is provided, then set it to that level.
+If @var{n} (from 0..4) is provided, then set it to that level.
 This affects the kind of messages sent to the server log.
 Level 0 is error messages only;
 level 1 adds warnings;
 level 2 adds informational messages;
-and level 3 adds debugging messages.
+level 3 adds debugging messages;
+and level 4 adds verbose low-level debug messages.
 The default is level 2, but that can be overridden on
 the command line along with the location of that log
 file (which is normally the server's standard output).