tcl/board/at91sam9263-ek.cfg

   1 # SPDX-License-Identifier: GPL-2.0-or-later
   2
   3 ################################################################################
   4 # Atmel AT91SAM9263-EK eval board
   5 ################################################################################
   6
   7 source [find mem_helper.tcl]
   8 source [find target/at91sam9263.cfg]
   9 uplevel #0 [list source [find chip/atmel/at91/hardware.cfg]]
  10 uplevel #0 [list source [find chip/atmel/at91/at91sam9263.cfg]]
  11 uplevel #0 [list source [find chip/atmel/at91/at91sam9263_matrix.cfg]]
  12 uplevel #0 [list source [find chip/atmel/at91/at91sam9_init.cfg]]
  13
  14 # By default S1 is open and this means that NTRST is not connected.
  15 # The reset_config in target/at91sam9263.cfg is overridden here.
  16 # (or S1 must be populated with a 0 Ohm resistor)
  17 reset_config srst_only
  18
  19 scan_chain
  20 $_TARGETNAME configure -event gdb-attach { reset init }
  21 $_TARGETNAME configure -event reset-init { at91sam9263ek_reset_init }
  22 $_TARGETNAME configure -event reset-start { at91sam9_reset_start }
  23
  24 proc at91sam9263ek_reset_init { } {
  25
  26         set config(master_pll_div)      14
  27         set config(master_pll_mul)      171
  28
  29         set val $::AT91_WDT_WDV                                                 ;# Counter Value
  30         set val [expr {$val | $::AT91_WDT_WDDIS}]               ;# Watchdog Disable
  31         set val [expr {$val | $::AT91_WDT_WDD}]                 ;# Delta Value
  32         set val [expr {$val | $::AT91_WDT_WDDBGHLT}]    ;# Debug Halt
  33         set val [expr {$val | $::AT91_WDT_WDIDLEHLT}]   ;# Idle Halt
  34
  35         set config(wdt_mr_val) $val
  36
  37         set config(sdram_piod) 1
  38         ;# EBI_CSA, no pull-ups for D[15:0], CS1 SDRAM, CS3 NAND Flash
  39         set config(matrix_ebicsa_addr)  $::AT91_MATRIX_EBI0CSA
  40
  41         set val $::AT91_MATRIX_EBI0_DBPUC
  42         set val [expr {$val | $::AT91_MATRIX_EBI0_VDDIOMSEL_3_3V}]
  43         set val [expr {$val | $::AT91_MATRIX_EBI0_CS1A_SDRAMC}]
  44         set config(matrix_ebicsa_val) $val
  45
  46         ;# SDRAMC_CR - Configuration register
  47         set val $::AT91_SDRAMC_NC_9
  48         set val [expr {$val | $::AT91_SDRAMC_NR_13}]
  49         set val [expr {$val | $::AT91_SDRAMC_NB_4}]
  50         set val [expr {$val | $::AT91_SDRAMC_CAS_3}]
  51         set val [expr {$val | $::AT91_SDRAMC_DBW_32}]
  52         set val [expr {$val | (1 <<  8)}]               ;# Write Recovery Delay
  53         set val [expr {$val | (7 << 12)}]               ;# Row Cycle Delay
  54         set val [expr {$val | (2 << 16)}]               ;# Row Precharge Delay
  55         set val [expr {$val | (2 << 20)}]               ;# Row to Column Delay
  56         set val [expr {$val | (5 << 24)}]               ;# Active to Precharge Delay
  57         set val [expr {$val | (1 << 28)}]               ;# Exit Self Refresh to Active Delay
  58
  59         set config(sdram_cr_val) $val
  60
  61         set config(sdram_tr_val) 0x13c
  62
  63         set config(sdram_base) $::AT91_CHIPSELECT_1
  64         at91sam9_reset_init $config
  65 }