tcl/target: Add Nordic nRF52 config

[openocd.git] / tcl / target / stm32f2x.cfg

diff --git a/tcl/target/stm32f2x.cfg b/tcl/target/stm32f2x.cfg
index a47b115d22bf9227f9f73df7937060e934b07130..0e734debbf153008d5994f2b214bfdf6d16aaece 100644 (file)
--- a/tcl/target/stm32f2x.cfg
+++ b/tcl/target/stm32f2x.cfg
@@ -1,16 +1,18 @@
-# script for stm32f2xxx
+# script for stm32f2x family
+
+#
+# stm32 devices support both JTAG and SWD transports.
+#
+source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
 } else {
-   set _CHIPNAME stm32f2xxx
+   set _CHIPNAME stm32f2x
 }
 
-if { [info exists ENDIAN] } {
-   set _ENDIAN $ENDIAN
-} else {
-   set _ENDIAN little
-}
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
 # By default use 64kB
@@ -26,20 +28,27 @@ if { [info exists WORKAREASIZE] } {
 # bit more to be on the safe side. Perhaps superstition, but if are
 # running off a crystal, we can run closer to the limit. Note
 # that there can be a pretty wide band where things are more or less stable.
-jtag_khz 1000
+adapter_khz 1000
 
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
+adapter_nsrst_delay 100
+if {[using_jtag]} {
+ jtag_ntrst_delay 100
+}
 
 #jtag scan chain
 if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
-  # See STM Document RM0033
-  # Section 32.6.3 - corresponds to Cortex-M3 r2p0
-   set _CPUTAPID 0x4ba00477
+   if { [using_jtag] } {
+      # See STM Document RM0033
+      # Section 32.6.3 - corresponds to Cortex-M3 r2p0
+      set _CPUTAPID 0x4ba00477
+   } {
+      set _CPUTAPID 0x2ba01477
+   }
 }
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
 if { [info exists BSTAPID] } {
    set _BSTAPID $BSTAPID
@@ -49,13 +58,39 @@ if { [info exists BSTAPID] } {
   # 
   set _BSTAPID 0x06411041
 }
-jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
+
+if {[using_jtag]} {
+ swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
+}
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
 
+reset_config srst_nogate
+
+if {![using_hla]} {
+   # if srst is not fitted use SYSRESETREQ to
+   # perform a soft reset
+   cortex_m reset_config sysresetreq
+}
+
+$_TARGETNAME configure -event examine-end {
+       # DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
+       mmw 0xE0042004 0x00000007 0
+
+       # Stop watchdog counters during halt
+       # DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
+       mmw 0xE0042008 0x00001800 0
+}
+
+$_TARGETNAME configure -event trace-config {
+       # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
+       # change this value accordingly to configure trace pins
+       # assignment
+       mmw 0xE0042004 0x00000020 0
+}