# Utility code for DaVinci-family chips
#
-# davinci_pinmux: assigns PINMUX$reg <== $value
+# davinci_pinmux: assigns PINMUX$reg <== $value
proc davinci_pinmux {soc reg value} {
mww [expr [dict get $soc sysbase] + 4 * $reg] $value
}
-# mrw: "memory read word", returns value of $reg
-proc mrw {reg} {
- set value ""
- ocd_mem2array value 32 $reg 1
- return $value(0)
-}
-
-# mmw: "memory modify word", updates value of $reg
-# $reg <== ((value & ~$clearbits) | $setbits)
-proc mmw {reg setbits clearbits} {
- set old [mrw $reg]
- set new [expr ($old & ~$clearbits) | $setbits]
- mww $reg $new
-}
+source [find mem_helper.tcl]
#
# pll_setup: initialize PLL
# For PLLs that don't have a given register (e.g. plldiv8), or where a
# given divider is non-programmable, caller provides *NO* config mapping.
#
-# REVISIT there are minor differences between the PLL controllers.
-# Handle those; maybe check the ID register. This version behaves
-# for at least the dm355. On dm6446 and dm357 the PLLRST polarity
-# is different. On dm365 there are more changes.
-#
-proc pll_setup {pll_addr mult config} {
+
+# PLL version 0x02: tested on dm355
+# REVISIT: On dm6446/dm357 the PLLRST polarity is different.
+proc pll_v02_setup {pll_addr mult config} {
set pll_ctrl_addr [expr $pll_addr + 0x100]
set pll_ctrl [mrw $pll_ctrl_addr]
# 1 - clear CLKMODE (bit 8) iff using on-chip oscillator
- # NOTE: this assumes we should clear that bit
+ # NOTE: this assumes we should clear that bit
set pll_ctrl [expr $pll_ctrl & ~0x0100]
mww $pll_ctrl_addr $pll_ctrl
set pll_ctrl [expr $pll_ctrl & ~0x0010]
mww $pll_ctrl_addr $pll_ctrl
- # 9 - optional: write prediv, postdiv, and pllm
- # NOTE: for dm355 PLL1, postdiv is controlled via MISC register
+ # 9 - optional: write prediv, postdiv, and pllm
+ # NOTE: for dm355 PLL1, postdiv is controlled via MISC register
mww [expr $pll_addr + 0x0110] [expr ($mult - 1) & 0xff]
if { [dict exists $config prediv] } {
set div [dict get $config prediv]
mww [expr $pll_addr + 0x0128] $div
}
- # 10 - optional: set plldiv1, plldiv2, ...
+ # 10 - optional: set plldiv1, plldiv2, ...
# NOTE: this assumes some registers have their just-reset values:
# - PLLSTAT.GOSTAT is clear when we enter
# - ALNCTL has everything set
set go 1
}
if { [dict exists $config div2] } {
- 1et div [dict get $config div2]
+ set div [dict get $config div2]
set div [expr 0x8000 | ($div - 1)]
mww [expr $pll_addr + 0x011c] $div
set go 1
if { [dict exists $config div3] } {
set div [dict get $config div3]
set div [expr 0x8000 | ($div - 1)]
- mww [expr $pll_addr + 0x011c] $div
+ mww [expr $pll_addr + 0x0120] $div
set go 1
}
if { [dict exists $config div4] } {
set pllstat [expr $pll_addr + 0x013c]
while {[expr [mrw $pllstat] & 0x01] != 0} { sleep 1 }
}
+ mww [expr $pll_addr + 0x0138] 0x00
# 11 - wait at least 5 usec for reset to finish
# (assume covered by overheads including JTAG messaging)
mww $pll_ctrl_addr $pll_ctrl
}
-# NOTE: dm6446 requires EMURSTIE set in MDCTL before certain
+# PLL version 0x03: tested on dm365
+proc pll_v03_setup {pll_addr mult config} {
+ set pll_ctrl_addr [expr $pll_addr + 0x100]
+ set pll_secctrl_addr [expr $pll_addr + 0x108]
+ set pll_ctrl [mrw $pll_ctrl_addr]
+
+ # 1 - power up the PLL
+ set pll_ctrl [expr $pll_ctrl & ~0x0002]
+ mww $pll_ctrl_addr $pll_ctrl
+
+ # 2 - clear PLLENSRC (bit 5)
+ set pll_ctrl [expr $pll_ctrl & ~0x0020]
+ mww $pll_ctrl_addr $pll_ctrl
+
+ # 2 - clear PLLEN (bit 0) ... enter bypass mode
+ set pll_ctrl [expr $pll_ctrl & ~0x0001]
+ mww $pll_ctrl_addr $pll_ctrl
+
+ # 3 - wait at least 4 refclk cycles
+ sleep 1
+
+ # 4 - set PLLRST (bit 3)
+ set pll_ctrl [expr $pll_ctrl | 0x0008]
+ mww $pll_ctrl_addr $pll_ctrl
+
+ # 5 - wait at least 5 usec
+ sleep 1
+
+ # 6 - clear PLLRST (bit 3)
+ set pll_ctrl [expr $pll_ctrl & ~0x0008]
+ mww $pll_ctrl_addr $pll_ctrl
+
+ # 9 - optional: write prediv, postdiv, and pllm
+ mww [expr $pll_addr + 0x0110] [expr ($mult / 2) & 0x1ff]
+ if { [dict exists $config prediv] } {
+ set div [dict get $config prediv]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0114] $div
+ }
+ if { [dict exists $config postdiv] } {
+ set div [dict get $config postdiv]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0128] $div
+ }
+
+ # 10 - write start sequence to PLLSECCTL
+ mww $pll_secctrl_addr 0x00470000
+ mww $pll_secctrl_addr 0x00460000
+ mww $pll_secctrl_addr 0x00400000
+ mww $pll_secctrl_addr 0x00410000
+
+ # 11 - optional: set plldiv1, plldiv2, ...
+ # NOTE: this assumes some registers have their just-reset values:
+ # - PLLSTAT.GOSTAT is clear when we enter
+ set aln 0
+ if { [dict exists $config div1] } {
+ set div [dict get $config div1]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0118] $div
+ set aln [expr $aln | 0x1]
+ } else {
+ mww [expr $pll_addr + 0x0118] 0
+ }
+ if { [dict exists $config div2] } {
+ set div [dict get $config div2]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x011c] $div
+ set aln [expr $aln | 0x2]
+ } else {
+ mww [expr $pll_addr + 0x011c] 0
+ }
+ if { [dict exists $config div3] } {
+ set div [dict get $config div3]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0120] $div
+ set aln [expr $aln | 0x4]
+ } else {
+ mww [expr $pll_addr + 0x0120] 0
+ }
+ if { [dict exists $config oscdiv] } {
+ set div [dict get $config oscdiv]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0124] $div
+ } else {
+ mww [expr $pll_addr + 0x0124] 0
+ }
+ if { [dict exists $config div4] } {
+ set div [dict get $config div4]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0160] $div
+ set aln [expr $aln | 0x8]
+ } else {
+ mww [expr $pll_addr + 0x0160] 0
+ }
+ if { [dict exists $config div5] } {
+ set div [dict get $config div5]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0164] $div
+ set aln [expr $aln | 0x10]
+ } else {
+ mww [expr $pll_addr + 0x0164] 0
+ }
+ if { [dict exists $config div6] } {
+ set div [dict get $config div6]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0168] $div
+ set aln [expr $aln | 0x20]
+ } else {
+ mww [expr $pll_addr + 0x0168] 0
+ }
+ if { [dict exists $config div7] } {
+ set div [dict get $config div7]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x016c] $div
+ set aln [expr $aln | 0x40]
+ } else {
+ mww [expr $pll_addr + 0x016c] 0
+ }
+ if { [dict exists $config div8] } {
+ set div [dict get $config div8]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0170] $div
+ set aln [expr $aln | 0x80]
+ } else {
+ mww [expr $pll_addr + 0x0170] 0
+ }
+ if { [dict exists $config div9] } {
+ set div [dict get $config div9]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0174] $div
+ set aln [expr $aln | 0x100]
+ } else {
+ mww [expr $pll_addr + 0x0174] 0
+ }
+ if {$aln != 0} {
+ # clear pllcmd.GO
+ mww [expr $pll_addr + 0x0138] 0x00
+ # write alingment flags
+ mww [expr $pll_addr + 0x0140] $aln
+ # write pllcmd.GO; poll pllstat.GO
+ mww [expr $pll_addr + 0x0138] 0x01
+ set pllstat [expr $pll_addr + 0x013c]
+ while {[expr [mrw $pllstat] & 0x01] != 0} { sleep 1 }
+ }
+ mww [expr $pll_addr + 0x0138] 0x00
+ set addr [dict get $config ctladdr]
+ while {[expr [mrw $addr] & 0x0e000000] != 0x0e000000} { sleep 1 }
+
+ # 12 - set PLLEN (bit 0) ... leave bypass mode
+ set pll_ctrl [expr $pll_ctrl | 0x0001]
+ mww $pll_ctrl_addr $pll_ctrl
+}
+
+# NOTE: dm6446 requires EMURSTIE set in MDCTL before certain
# modules can be enabled.
# prepare a non-DSP module to be enabled; finish with psc_go
mmw [expr $psc_addr + 0x0a00 + (4 * $module)] 0x03 0x1f
}
-# execute non-DSP PSC transition(s) set up by psc_enable
+# prepare a non-DSP module to be reset; finish with psc_go
+proc psc_reset {module} {
+ set psc_addr 0x01c41000
+ # write MDCTL
+ mmw [expr $psc_addr + 0x0a00 + (4 * $module)] 0x01 0x1f
+}
+
+# execute non-DSP PSC transition(s) set up by psc_enable, psc_reset, etc
proc psc_go {} {
set psc_addr 0x01c41000
set ptstat_addr [expr $psc_addr + 0x0128]
# wait for PTSTAT.go to clear (again ignoring DSP power domain)
while { [expr [mrw $ptstat_addr] & 0x01] != 0 } { sleep 1 }
}
+
+#
+# A reset using only SRST is a "Warm Reset", resetting everything in the
+# chip except ARM emulation (and everything _outside_ the chip that hooks
+# up to SRST). But many boards don't expose SRST via their JTAG connectors
+# (it's not present on TI-14 headers).
+#
+# From the chip-only perspective, a "Max Reset" is a "Warm" reset ... except
+# without any board-wide side effects, since it's triggered using JTAG using
+# either (a) ARM watchdog timer, or (b) ICEpick.
+#
+proc davinci_wdog_reset {} {
+ set timer2_phys 0x01c21c00
+
+ # NOTE -- on entry
+ # - JTAG communication with the ARM *must* be working OK; this
+ # may imply using adaptive clocking or disabling WFI-in-idle
+ # - current target must be the DaVinci ARM
+ # - that ARM core must be halted
+ # - timer2 clock is still enabled (PSC 29 on most chips)
+
+ #
+ # Part I -- run regardless of being halted via JTAG
+ #
+ # NOTE: for now, we assume there's no DSP that could control the
+ # watchdog; or, equivalently, SUSPSRC.TMR2SRC says the watchdog
+ # suspend signal is controlled via ARM emulation suspend.
+ #
+
+ # EMUMGT_CLKSPEED: write FREE bit to run despite emulation halt
+ mww phys [expr $timer2_phys + 0x28] 0x00004000
+
+ #
+ # Part II -- in case watchdog hasn't been set up
+ #
+
+ # TCR: disable, force internal clock source
+ mww phys [expr $timer2_phys + 0x20] 0
+
+ # TGCR: reset, force to 64-bit wdog mode, un-reset ("initial" state)
+ mww phys [expr $timer2_phys + 0x24] 0
+ mww phys [expr $timer2_phys + 0x24] 0x110b
+
+ # clear counter (TIM12, TIM34) and period (PRD12, PRD34) registers
+ # so watchdog triggers ASAP
+ mww phys [expr $timer2_phys + 0x10] 0
+ mww phys [expr $timer2_phys + 0x14] 0
+ mww phys [expr $timer2_phys + 0x18] 0
+ mww phys [expr $timer2_phys + 0x1c] 0
+
+ # WDTCR: put into pre-active state, then active
+ mww phys [expr $timer2_phys + 0x28] 0xa5c64000
+ mww phys [expr $timer2_phys + 0x28] 0xda7e4000
+
+ #
+ # Part III -- it's ready to rumble
+ #
+
+ # WDTCR: write invalid WDKEY to trigger reset
+ mww phys [expr $timer2_phys + 0x28] 0x00004000
+}
Code Review / openocd.git / blobdiff