tcl: remove trailing whitespace

[openocd.git] / tcl / board / at91sam9g20-ek.cfg

diff --git a/tcl/board/at91sam9g20-ek.cfg b/tcl/board/at91sam9g20-ek.cfg
index 741d6018dc467e6feecf91cd1b711187e818dc15..03296c50e314287b868ed6c2515d82945d843bf7 100644 (file)
--- a/tcl/board/at91sam9g20-ek.cfg
+++ b/tcl/board/at91sam9g20-ek.cfg
@@ -19,7 +19,7 @@ set _FLASHTYPE nandflash_cs3
 
 reset_config srst_only
 
-adapter_nsrst_delay 200
+adapter srst delay 200
 jtag_ntrst_delay 200
 
 # If you don't want to execute built-in boot rom code (and there are good reasons at times not to do that) in the
@@ -54,7 +54,7 @@ proc at91sam9g20_reset_start { } {
        # jtag speed without causing GDB keep alive problem.
 
        arm7_9 fast_memory_access disable
-       adapter_khz 2                   ;# Slow-speed oscillator enabled at reset, so run jtag speed slow.
+       adapter speed 2                 ;# Slow-speed oscillator enabled at reset, so run jtag speed slow.
        halt                            ;# Make sure processor is halted, or error will result in following steps.
        wait_halt 10000
        mww 0xfffffd08 0xa5000501       ;# RSTC_MR : enable user reset.
@@ -103,7 +103,7 @@ proc at91sam9g20_reset_init { } {
 
        # Switch over to adaptive clocking.
 
-       adapter_khz 0
+       adapter speed 0
 
        # Enable faster DCC downloads and memory accesses.
 
@@ -139,13 +139,13 @@ proc at91sam9g20_reset_init { } {
        # (MT29F2G08AACWP) can be established by setting four registers in order:  SMC_SETUP3,
        # SMC_PULSE3, SMC_CYCLE3, and SMC_MODE3.  Computing the exact values of these registers
        # is a little tedious to do here.  If you have questions about how to do this, Atmel has
-       # a decent application note #6255B that covers this process. 
+       # a decent application note #6255B that covers this process.
 
        mww 0xffffec30 0x00020002       ;# SMC_SETUP3 : 2 clock cycle setup for NRD and NWE
        mww 0xffffec34 0x04040404       ;# SMC_PULSE3 : 4 clock cycle pulse for all signals
        mww 0xffffec38 0x00070006       ;# SMC_CYCLE3 : 7 clock cycle NRD and 6 NWE cycle
-       mww 0xffffec3C 0x00020003       ;# SMC_MODE3 : NRD and NWE control, no NWAIT, 8-bit DBW, 
-   
+       mww 0xffffec3C 0x00020003       ;# SMC_MODE3 : NRD and NWE control, no NWAIT, 8-bit DBW,
+
        mww 0xffffe800 0x00000001       ;# ECC_CR : reset the ECC parity registers
        mww 0xffffe804 0x00000002       ;# ECC_MR : page size is 2112 words (word is 8 bits)
 
@@ -169,7 +169,7 @@ proc at91sam9g20_reset_init { } {
        #       TRC = 9 cycles
        #       TWR = 2 cycles
        #       9 column, 13 row, 4 banks
-       #       refresh equal to or less then 7.8 us for commerical/industrial rated devices
+       #       refresh equal to or less then 7.8 us for commercial/industrial rated devices
        #
        #       Thus SDRAM_CR = 0xa6339279
 
@@ -216,4 +216,3 @@ proc at91sam9g20_reset_init { } {
 
        mww 0xffffea04 0x0000039c
 }
-