Rick Altherr <kc8apf@kc8apf.net> - update syntax

[openocd.git] / src / target / target / zy1000.cfg

diff --git a/src/target/target/zy1000.cfg b/src/target/target/zy1000.cfg
index 9e8cdb9c9a9d54119d3abfd68e445b3e55a418c5..2fb2db323f1c9ab19280944b77f806d92fce005f 100644 (file)
--- a/src/target/target/zy1000.cfg
+++ b/src/target/target/zy1000.cfg
@@ -13,18 +13,79 @@ reset_config srst_only srst_pulls_trst
 #format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
 jtag_device 4 0x1 0xf 0xe
 
-#target configuration
-target arm7tdmi little 0 arm7tdmi-s_r4
+target create target0 arm7tdmi -endian little -chain-position 0 -variant arm7tdmi-s_r4
 
 # at CPU CLK <32kHz this must be disabled
 arm7_9 fast_memory_access enable
 arm7_9 dcc_downloads enable
 
 flash bank ecosflash 0x01000000 0x200000 2 2 0 ecos/at91eb40a.elf
-target_script 0 reset event/zy1000_reset.script
+[new_target_name] configure -event reset-init { 
+       # Set up chip selects & timings
+       mww 0xFFE00000 0x0100273D
+       mww 0xFFE00004 0x08002125
+       mww 0xFFEe0008 0x02002125
+       mww 0xFFE0000c 0x03002125
+       mww 0xFFE00010 0x40000000
+       mww 0xFFE00014 0x50000000
+       mww 0xFFE00018 0x60000000
+       mww 0xFFE0001c 0x70000000
+       mww 0xFFE00020 0x00000001
+       mww 0xFFE00024 0x00000000
+       
+       # remap  
+       mww 0xFFFFF124 0xFFFFFFFF  
+       mww 0xffff0010 0x100
+       mww 0xffff0034 0x100
+       
+       #disable 16x5x UART interrupts
+       mww 0x08020004 0
+}
 
 # required for usable performance. Used for lots of
 # other things than flash programming.
-working_area 0 0x00000000 0x20000 nobackup
+[new_target_name] configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0
 
 jtag_khz 16000
+
+
+proc production_info {} {
+       return "Serial number is official MAC number. Format XXXXXXXXXXXX"
+}
+
+# There is no return value from this procedure. If it is
+# successful it does not throw an exception
+#
+# Progress messages are output via puts 
+proc production {firmwarefile serialnumber} {
+       if {[string length $serialnumber]!=12} {
+               puts "Invalid serial number"
+               return
+       }
+
+       puts "Power cycling target"
+       power off
+       sleep 3000
+       power on
+       sleep 1000
+       reset init
+       flash write_image erase $firmwarefile 0x1000000 bin
+       verify_image $firmwarefile 0x1000000 bin
+
+       # Big endian... weee!!!!
+       puts "Setting MAC number to $serialnumber"      
+       flash fillw [expr 0x1030000-0x8] "0x[string range $serialnumber 2 3][string range $serialnumber 0 1]0000" 1
+       flash fillw [expr 0x1030000-0x4] "0x[string range $serialnumber 10 11][string range $serialnumber 8 9][string range $serialnumber 6 7][string range $serialnumber 4 5]" 1
+       puts "Production successful"
+} 
+
+
+proc production_test {} {
+       power on
+       sleep 1000
+       target_request debugmsgs enable
+       reset run
+       sleep 25000
+       target_request debugmsgs disable
+       return "See IP address above..."
+}