Remove FSF address from GPL notices
[openocd.git] / src / jtag / hla / hla_layout.h
index d7b5d9353f5d77c24f962e4fa24df3a604af496a..986667fff3253f45cdaaa46ae1433a9aca144dd0 100644 (file)
  *   GNU General Public License for more details.                          *
  *                                                                         *
  *   You should have received a copy of the GNU General Public License     *
- *   along with this program; if not, write to the                         *
- *   Free Software Foundation, Inc.,                                       *
- *   51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.           *
+ *   along with this program.  If not, see <http://www.gnu.org/licenses/>. *
  ***************************************************************************/
 
 #ifndef _HL_LAYOUT_H
 #define _HL_LAYOUT_H
 
+#include <target/armv7m_trace.h>
+
 /** */
 struct hl_interface_s;
 struct hl_interface_param_s;
@@ -35,25 +35,25 @@ extern struct hl_layout_api_s icdi_usb_layout_api;
 /** */
 struct hl_layout_api_s {
        /** */
-       int (*open) (struct hl_interface_param_s *param, void **fd);
+       int (*open) (struct hl_interface_param_s *param, void **handle);
        /** */
-       int (*close) (void *fd);
+       int (*close) (void *handle);
        /** */
-       int (*reset) (void *fd);
+       int (*reset) (void *handle);
        /** */
-       int (*assert_srst) (void *fd, int srst);
+       int (*assert_srst) (void *handle, int srst);
        /** */
-       int (*run) (void *fd);
+       int (*run) (void *handle);
        /** */
-       int (*halt) (void *fd);
+       int (*halt) (void *handle);
        /** */
-       int (*step) (void *fd);
+       int (*step) (void *handle);
        /** */
-       int (*read_regs) (void *fd);
+       int (*read_regs) (void *handle);
        /** */
-       int (*read_reg) (void *fd, int num, uint32_t *val);
+       int (*read_reg) (void *handle, int num, uint32_t *val);
        /** */
-       int (*write_reg) (void *fd, int num, uint32_t val);
+       int (*write_reg) (void *handle, int num, uint32_t val);
        /** */
        int (*read_mem) (void *handle, uint32_t addr, uint32_t size,
                        uint32_t count, uint8_t *buffer);
@@ -62,8 +62,48 @@ struct hl_layout_api_s {
                        uint32_t count, const uint8_t *buffer);
        /** */
        int (*write_debug_reg) (void *handle, uint32_t addr, uint32_t val);
-       /** */
-       int (*idcode) (void *fd, uint32_t *idcode);
+       /**
+        * Read the idcode of the target connected to the adapter
+        *
+        * If the adapter doesn't support idcode retrieval, this callback should
+        * store 0 to indicate a wildcard match.
+        *
+        * @param handle A pointer to the device-specific handle
+        * @param idcode Storage for the detected idcode
+        * @returns ERROR_OK on success, or an error code on failure.
+        */
+       int (*idcode) (void *handle, uint32_t *idcode);
+       /** */
+       int (*override_target) (const char *targetname);
+       /** */
+       int (*custom_command) (void *handle, const char *command);
+       /** */
+       int (*speed)(void *handle, int khz, bool query);
+       /**
+        * Configure trace parameters for the adapter
+        *
+        * @param handle A handle to adapter
+        * @param enabled Whether to enable trace
+        * @param pin_protocol Configured pin protocol
+        * @param port_size Trace port width for sync mode
+        * @param trace_freq A pointer to the configured trace
+        * frequency; if it points to 0, the adapter driver must write
+        * its maximum supported rate there
+        * @returns ERROR_OK on success, an error code on failure.
+        */
+       int (*config_trace)(void *handle, bool enabled, enum tpio_pin_protocol pin_protocol,
+                           uint32_t port_size, unsigned int *trace_freq);
+       /**
+        * Poll for new trace data
+        *
+        * @param handle A handle to adapter
+        * @param buf A pointer to buffer to store received data
+        * @param size A pointer to buffer size; must be filled with
+        * the actual amount of bytes written
+        *
+        * @returns ERROR_OK on success, an error code on failure.
+        */
+       int (*poll_trace)(void *handle, uint8_t *buf, size_t *size);
        /** */
        enum target_state (*state) (void *fd);
 };

Linking to existing account procedure

If you already have an account and want to add another login method you MUST first sign in with your existing account and then change URL to read https://review.openocd.org/login/?link to get to this page again but this time it'll work for linking. Thank you.

SSH host keys fingerprints

1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=..              |
|+o..   .         |
|*.o   . .        |
|+B . . .         |
|Bo. = o S        |
|Oo.+ + =         |
|oB=.* = . o      |
| =+=.+   + E     |
|. .=o   . o      |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)