* 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. *
***************************************************************************/
-/* This code uses information contained in the MPSSE specification which was
+/**
+ * @file
+ * JTAG adapters based on the FT2232 full and high speed USB parts are
+ * popular low cost JTAG debug solutions. Many FT2232 based JTAG adapters
+ * are discrete, but development boards may integrate them as alternatives
+ * to more capable (and expensive) third party JTAG pods.
+ *
+ * JTAG uses only one of the two communications channels ("MPSSE engines")
+ * on these devices. Adapters based on FT4232 parts have four ports/channels
+ * (A/B/C/D), instead of just two (A/B).
+ *
+ * Especially on development boards integrating one of these chips (as
+ * opposed to discrete pods/dongles), the additional channels can be used
+ * for a variety of purposes, but OpenOCD only uses one channel at a time.
+ *
+ * - As a USB-to-serial adapter for the target's console UART ...
+ * which may be able to support ROM boot loaders that load initial
+ * firmware images to flash (or SRAM).
+ *
+ * - On systems which support ARM's SWD in addition to JTAG, or instead
+ * of it, that second port can be used for reading SWV/SWO trace data.
+ *
+ * - Additional JTAG links, e.g. to a CPLD or * FPGA.
+ *
+ * FT2232 based JTAG adapters are "dumb" not "smart", because most JTAG
+ * request/response interactions involve round trips over the USB link.
+ * A "smart" JTAG adapter has intelligence close to the scan chain, so it
+ * can for example poll quickly for a status change (usually taking on the
+ * order of microseconds not milliseconds) before beginning a queued
+ * transaction which require the previous one to have completed.
+ *
+ * There are dozens of adapters of this type, differing in details which
+ * this driver needs to understand. Those "layout" details are required
+ * as part of FT2232 driver configuration.
+ *
+ * This code uses information contained in the MPSSE specification which was
* found here:
* http://www.ftdichip.com/Documents/AppNotes/AN2232C-01_MPSSE_Cmnd.pdf
* Hereafter this is called the "MPSSE Spec".
*
* The datasheet for the ftdichip.com's FT2232D part is here:
* http://www.ftdichip.com/Documents/DataSheets/DS_FT2232D.pdf
+ *
+ * Also note the issue with code 0x4b (clock data to TMS) noted in
+ * http://developer.intra2net.com/mailarchive/html/libftdi/2009/msg00292.html
+ * which can affect longer JTAG state paths.
*/
#ifdef HAVE_CONFIG_H
#endif
/* project specific includes */
-#include "interface.h"
-#include "commands.h"
+#include <jtag/interface.h>
+#include <transport/transport.h>
#include <helper/time_support.h>
#if IS_CYGWIN == 1
/* FT2232 access library includes */
#if BUILD_FT2232_FTD2XX == 1
#include <ftd2xx.h>
+#include "ftd2xx_common.h"
+
+enum ftdi_interface
+{
+ INTERFACE_ANY = 0,
+ INTERFACE_A = 1,
+ INTERFACE_B = 2,
+ INTERFACE_C = 3,
+ INTERFACE_D = 4
+};
+
#elif BUILD_FT2232_LIBFTDI == 1
#include <ftdi.h>
#endif
static char * ft2232_device_desc_A = NULL;
static char* ft2232_device_desc = NULL;
static char* ft2232_serial = NULL;
-static char* ft2232_layout = NULL;
static uint8_t ft2232_latency = 2;
static unsigned ft2232_max_tck = FTDI_2232C_MAX_TCK;
int (*init)(void);
void (*reset)(int trst, int srst);
void (*blink)(void);
+ int channel;
};
/* init procedures for supported layouts */
static int usbjtag_init(void);
static int jtagkey_init(void);
+static int lm3s811_jtag_init(void);
+static int icdi_jtag_init(void);
static int olimex_jtag_init(void);
static int flyswatter_init(void);
+static int minimodule_init(void);
static int turtle_init(void);
static int comstick_init(void);
static int stm32stick_init(void);
static int sheevaplug_init(void);
static int icebear_jtag_init(void);
static int cortino_jtag_init(void);
+static int signalyzer_init(void);
static int signalyzer_h_init(void);
static int ktlink_init(void);
+static int redbee_init(void);
+static int lisa_l_init(void);
+static int flossjtag_init(void);
+static int xds100v2_init(void);
/* reset procedures for supported layouts */
-static void usbjtag_reset(int trst, int srst);
+static void ftx23_reset(int trst, int srst);
static void jtagkey_reset(int trst, int srst);
static void olimex_jtag_reset(int trst, int srst);
static void flyswatter_reset(int trst, int srst);
+static void minimodule_reset(int trst, int srst);
static void turtle_reset(int trst, int srst);
static void comstick_reset(int trst, int srst);
static void stm32stick_reset(int trst, int srst);
static void icebear_jtag_reset(int trst, int srst);
static void signalyzer_h_reset(int trst, int srst);
static void ktlink_reset(int trst, int srst);
+static void redbee_reset(int trst, int srst);
+static void xds100v2_reset(int trst, int srst);
/* blink procedures for layouts that support a blinking led */
static void olimex_jtag_blink(void);
static void turtle_jtag_blink(void);
static void signalyzer_h_blink(void);
static void ktlink_blink(void);
+static void lisa_l_blink(void);
+static void flossjtag_blink(void);
+
+/* common transport support options */
+
+//static const char *jtag_and_swd[] = { "jtag", "swd", NULL };
static const struct ft2232_layout ft2232_layouts[] =
{
- { "usbjtag", usbjtag_init, usbjtag_reset, NULL },
- { "jtagkey", jtagkey_init, jtagkey_reset, NULL },
- { "jtagkey_prototype_v1", jtagkey_init, jtagkey_reset, NULL },
- { "oocdlink", jtagkey_init, jtagkey_reset, NULL },
- { "signalyzer", usbjtag_init, usbjtag_reset, NULL },
- { "evb_lm3s811", usbjtag_init, usbjtag_reset, NULL },
- { "luminary_icdi", usbjtag_init, usbjtag_reset, NULL },
- { "olimex-jtag", olimex_jtag_init, olimex_jtag_reset, olimex_jtag_blink },
- { "flyswatter", flyswatter_init, flyswatter_reset, flyswatter_jtag_blink },
- { "turtelizer2", turtle_init, turtle_reset, turtle_jtag_blink },
- { "comstick", comstick_init, comstick_reset, NULL },
- { "stm32stick", stm32stick_init, stm32stick_reset, NULL },
- { "axm0432_jtag", axm0432_jtag_init, axm0432_jtag_reset, NULL },
- { "sheevaplug", sheevaplug_init, sheevaplug_reset, NULL },
- { "icebear", icebear_jtag_init, icebear_jtag_reset, NULL },
- { "cortino", cortino_jtag_init, comstick_reset, NULL },
- { "signalyzer-h", signalyzer_h_init, signalyzer_h_reset, signalyzer_h_blink },
- { "ktlink", ktlink_init, ktlink_reset, ktlink_blink },
- { NULL, NULL, NULL, NULL },
+ { .name = "usbjtag",
+ .init = usbjtag_init,
+ .reset = ftx23_reset,
+ },
+ { .name = "jtagkey",
+ .init = jtagkey_init,
+ .reset = jtagkey_reset,
+ },
+ { .name = "jtagkey_prototype_v1",
+ .init = jtagkey_init,
+ .reset = jtagkey_reset,
+ },
+ { .name = "oocdlink",
+ .init = jtagkey_init,
+ .reset = jtagkey_reset,
+ },
+ { .name = "signalyzer",
+ .init = signalyzer_init,
+ .reset = ftx23_reset,
+ },
+ { .name = "evb_lm3s811",
+ .init = lm3s811_jtag_init,
+ .reset = ftx23_reset,
+ },
+ { .name = "luminary_icdi",
+ .init = icdi_jtag_init,
+ .reset = ftx23_reset,
+ },
+ { .name = "olimex-jtag",
+ .init = olimex_jtag_init,
+ .reset = olimex_jtag_reset,
+ .blink = olimex_jtag_blink
+ },
+ { .name = "flyswatter",
+ .init = flyswatter_init,
+ .reset = flyswatter_reset,
+ .blink = flyswatter_jtag_blink
+ },
+ { .name = "minimodule",
+ .init = minimodule_init,
+ .reset = minimodule_reset,
+ },
+ { .name = "turtelizer2",
+ .init = turtle_init,
+ .reset = turtle_reset,
+ .blink = turtle_jtag_blink
+ },
+ { .name = "comstick",
+ .init = comstick_init,
+ .reset = comstick_reset,
+ },
+ { .name = "stm32stick",
+ .init = stm32stick_init,
+ .reset = stm32stick_reset,
+ },
+ { .name = "axm0432_jtag",
+ .init = axm0432_jtag_init,
+ .reset = axm0432_jtag_reset,
+ },
+ { .name = "sheevaplug",
+ .init = sheevaplug_init,
+ .reset = sheevaplug_reset,
+ },
+ { .name = "icebear",
+ .init = icebear_jtag_init,
+ .reset = icebear_jtag_reset,
+ },
+ { .name = "cortino",
+ .init = cortino_jtag_init,
+ .reset = comstick_reset,
+ },
+ { .name = "signalyzer-h",
+ .init = signalyzer_h_init,
+ .reset = signalyzer_h_reset,
+ .blink = signalyzer_h_blink
+ },
+ { .name = "ktlink",
+ .init = ktlink_init,
+ .reset = ktlink_reset,
+ .blink = ktlink_blink
+ },
+ { .name = "redbee-econotag",
+ .init = redbee_init,
+ .reset = redbee_reset,
+ },
+ { .name = "redbee-usb",
+ .init = redbee_init,
+ .reset = redbee_reset,
+ .channel = INTERFACE_B,
+ },
+ { .name = "lisa-l",
+ .init = lisa_l_init,
+ .reset = ftx23_reset,
+ .blink = lisa_l_blink,
+ .channel = INTERFACE_B,
+ },
+ { .name = "flossjtag",
+ .init = flossjtag_init,
+ .reset = ftx23_reset,
+ .blink = flossjtag_blink,
+ },
+ { .name = "xds100v2",
+ .init = xds100v2_init,
+ .reset = xds100v2_reset,
+ },
+ { .name = NULL, /* END OF TABLE */ },
};
-static uint8_t nTRST, nTRSTnOE, nSRST, nSRSTnOE;
+/* bitmask used to drive nTRST; usually a GPIOLx signal */
+static uint8_t nTRST;
+static uint8_t nTRSTnOE;
+/* bitmask used to drive nSRST; usually a GPIOLx signal */
+static uint8_t nSRST;
+static uint8_t nSRSTnOE;
+/** the layout being used with this debug session */
static const struct ft2232_layout *layout;
+
+/** default bitmask values driven on DBUS: TCK/TDI/TDO/TMS and GPIOL(0..4) */
static uint8_t low_output = 0x0;
+
+/* note that direction bit == 1 means that signal is an output */
+
+/** default direction bitmask for DBUS: TCK/TDI/TDO/TMS and GPIOL(0..4) */
static uint8_t low_direction = 0x0;
+/** default value bitmask for CBUS GPIOH(0..4) */
static uint8_t high_output = 0x0;
+/** default direction bitmask for CBUS GPIOH(0..4) */
static uint8_t high_direction = 0x0;
#if BUILD_FT2232_FTD2XX == 1
a comment would have been nice.
*/
+#if BUILD_FT2232_FTD2XX == 1
+#define FT2232_BUFFER_READ_QUEUE_SIZE (64*64)
+#else
+#define FT2232_BUFFER_READ_QUEUE_SIZE (64*4)
+#endif
+
#define FT2232_BUFFER_SIZE 131072
static uint8_t* ft2232_buffer = NULL;
{
#if BUILD_FT2232_FTD2XX == 1
FT_STATUS status;
- DWORD dw_bytes_written;
+ DWORD dw_bytes_written = 0;
if ((status = FT_Write(ftdih, buf, size, &dw_bytes_written)) != FT_OK)
{
*bytes_written = dw_bytes_written;
- LOG_ERROR("FT_Write returned: %lu", status);
+ LOG_ERROR("FT_Write returned: %s", ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
else
{
*bytes_written = dw_bytes_written;
- return ERROR_OK;
}
#elif BUILD_FT2232_LIBFTDI == 1
int retval;
else
{
*bytes_written = retval;
- return ERROR_OK;
}
#endif
+
+ if (*bytes_written != (uint32_t)size)
+ {
+ return ERROR_JTAG_DEVICE_ERROR;
+ }
+
+ return ERROR_OK;
}
static int ft2232_read(uint8_t* buf, uint32_t size, uint32_t* bytes_read)
*bytes_read, &dw_bytes_read)) != FT_OK)
{
*bytes_read = 0;
- LOG_ERROR("FT_Read returned: %lu", status);
+ LOG_ERROR("FT_Read returned: %s", ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
*bytes_read += dw_bytes_read;
LOG_DEBUG("%2.2x", buf);
uint32_t bytes_written;
- int retval = ft2232_write(&buf, 1, &bytes_written);
- if ((ERROR_OK != retval) || (bytes_written != 1))
+ int retval;
+
+ if ((retval = ft2232_write(&buf, sizeof(buf), &bytes_written)) != ERROR_OK)
{
LOG_ERROR("couldn't write command to %s adaptive clocking"
, enable ? "enable" : "disable");
{
uint32_t bytes_written;
uint8_t buf = enable ? 0x8b : 0x8a;
- int retval = ft2232_write(&buf, 1, &bytes_written);
- if ((ERROR_OK != retval) || (bytes_written != 1))
+
+ if (ft2232_write(&buf, sizeof(buf), &bytes_written) != ERROR_OK)
{
LOG_ERROR("couldn't write command to %s clk divide by 5"
, enable ? "enable" : "disable");
buf[2] = (speed >> 8) & 0xff; /* valueH */
LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
- if (((retval = ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if ((retval = ft2232_write(buf, sizeof(buf), &bytes_written)) != ERROR_OK)
{
LOG_ERROR("couldn't set FT2232 TCK speed");
return retval;
for (i = 0; i < ft2232_buffer_size; i++)
{
- line_p += snprintf(line_p, 256 - (line_p - line), "%2.2x ", ft2232_buffer[i]);
+ line_p += snprintf(line_p, sizeof(line) - (line_p - line), "%2.2x ", ft2232_buffer[i]);
if (i % 16 == 15)
{
LOG_DEBUG("%s", line);
LOG_DEBUG("thisrun_read: %i, bytes_read: %i",
thisrun_read,
(int)bytes_read);
- receive_pointer += bytes_read;
}
return ERROR_OK;
return predicted_size;
}
-static void usbjtag_reset(int trst, int srst)
+/* semi-generic FT2232/FT4232 reset code */
+static void ftx23_reset(int trst, int srst)
{
enum reset_types jtag_reset_config = jtag_get_reset_config();
if (trst == 1)
LOG_DEBUG("trst: %i, srst: %i, low_output: 0x%2.2x, low_direction: 0x%2.2x", trst, srst, low_output, low_direction);
}
+static void minimodule_reset(int trst, int srst)
+{
+ if (srst == 1)
+ {
+ low_output &= ~nSRST;
+ }
+ else if (srst == 0)
+ {
+ low_output |= nSRST;
+ }
+
+ /* command "set data bits low byte" */
+ buffer_write(0x80);
+ buffer_write(low_output);
+ buffer_write(low_direction);
+ LOG_DEBUG("trst: %i, srst: %i, low_output: 0x%2.2x, low_direction: 0x%2.2x", trst, srst, low_output, low_direction);
+}
+
static void turtle_reset(int trst, int srst)
{
trst = trst;
LOG_DEBUG("trst: %i, srst: %i, high_output: 0x%2.2x, high_direction: 0x%2.2x", trst, srst, high_output, high_direction);
}
+static void redbee_reset(int trst, int srst)
+{
+ if (trst == 1)
+ {
+ tap_set_state(TAP_RESET);
+ high_output &= ~nTRST;
+ }
+ else if (trst == 0)
+ {
+ high_output |= nTRST;
+ }
+
+ if (srst == 1)
+ {
+ high_output &= ~nSRST;
+ }
+ else if (srst == 0)
+ {
+ high_output |= nSRST;
+ }
+
+ /* command "set data bits low byte" */
+ buffer_write(0x82);
+ buffer_write(high_output);
+ buffer_write(high_direction);
+ LOG_DEBUG("trst: %i, srst: %i, high_output: 0x%2.2x, "
+ "high_direction: 0x%2.2x", trst, srst, high_output,
+ high_direction);
+}
+
+static void xds100v2_reset(int trst, int srst)
+{
+ if (trst == 1)
+ {
+ tap_set_state(TAP_RESET);
+ high_output &= ~nTRST;
+ }
+ else if (trst == 0)
+ {
+ high_output |= nTRST;
+ }
+
+ if (srst == 1)
+ {
+ high_output |= nSRST;
+ }
+ else if (srst == 0)
+ {
+ high_output &= ~nSRST;
+ }
+
+ /* command "set data bits low byte" */
+ buffer_write(0x82);
+ buffer_write(high_output);
+ buffer_write(high_direction);
+ LOG_DEBUG("trst: %i, srst: %i, high_output: 0x%2.2x, "
+ "high_direction: 0x%2.2x", trst, srst, high_output,
+ high_direction);
+}
+
static int ft2232_execute_runtest(struct jtag_command *cmd)
{
int retval;
return retval;
}
+/**
+ * Clock a bunch of TMS (or SWDIO) transitions, to change the JTAG
+ * (or SWD) state machine.
+ */
+static int ft2232_execute_tms(struct jtag_command *cmd)
+{
+ int retval = ERROR_OK;
+ unsigned num_bits = cmd->cmd.tms->num_bits;
+ const uint8_t *bits = cmd->cmd.tms->bits;
+ unsigned count;
+
+ DEBUG_JTAG_IO("TMS: %d bits", num_bits);
+
+ /* only send the maximum buffer size that FT2232C can handle */
+ count = 3 * DIV_ROUND_UP(num_bits, 4);
+ if (ft2232_buffer_size + 3*count + 1 > FT2232_BUFFER_SIZE) {
+ if (ft2232_send_and_recv(first_unsent, cmd) != ERROR_OK)
+ retval = ERROR_JTAG_QUEUE_FAILED;
+
+ require_send = 0;
+ first_unsent = cmd;
+ }
+
+ /* Shift out in batches of at most 6 bits; there's a report of an
+ * FT2232 bug in this area, where shifting exactly 7 bits can make
+ * problems with TMS signaling for the last clock cycle:
+ *
+ * http://developer.intra2net.com/mailarchive/html/
+ * libftdi/2009/msg00292.html
+ *
+ * Command 0x4b is: "Clock Data to TMS/CS Pin (no Read)"
+ *
+ * Note that pathmoves in JTAG are not often seven bits, so that
+ * isn't a particularly likely situation outside of "special"
+ * signaling such as switching between JTAG and SWD modes.
+ */
+ while (num_bits) {
+ if (num_bits <= 6) {
+ buffer_write(0x4b);
+ buffer_write(num_bits - 1);
+ buffer_write(*bits & 0x3f);
+ break;
+ }
+
+ /* Yes, this is lazy ... we COULD shift out more data
+ * bits per operation, but doing it in nybbles is easy
+ */
+ buffer_write(0x4b);
+ buffer_write(3);
+ buffer_write(*bits & 0xf);
+ num_bits -= 4;
+
+ count = (num_bits > 4) ? 4 : num_bits;
+
+ buffer_write(0x4b);
+ buffer_write(count - 1);
+ buffer_write((*bits >> 4) & 0xf);
+ num_bits -= count;
+
+ bits++;
+ }
+
+ require_send = 1;
+ return retval;
+}
+
static int ft2232_execute_pathmove(struct jtag_command *cmd)
{
int predicted_size = 0;
static int ft2232_execute_command(struct jtag_command *cmd)
{
int retval;
- retval = ERROR_OK;
switch (cmd->type)
{
case JTAG_RESET: retval = ft2232_execute_reset(cmd); break;
case JTAG_RUNTEST: retval = ft2232_execute_runtest(cmd); break;
- case JTAG_STATEMOVE: retval = ft2232_execute_statemove(cmd); break;
+ case JTAG_TLR_RESET: retval = ft2232_execute_statemove(cmd); break;
case JTAG_PATHMOVE: retval = ft2232_execute_pathmove(cmd); break;
case JTAG_SCAN: retval = ft2232_execute_scan(cmd); break;
case JTAG_SLEEP: retval = ft2232_execute_sleep(cmd); break;
case JTAG_STABLECLOCKS: retval = ft2232_execute_stableclocks(cmd); break;
+ case JTAG_TMS:
+ retval = ft2232_execute_tms(cmd);
+ break;
default:
LOG_ERROR("BUG: unknown JTAG command type encountered");
- exit(-1);
+ retval = ERROR_JTAG_QUEUE_FAILED;
+ break;
}
return retval;
}
while (cmd)
{
+ /* fill the write buffer with the desired command */
if (ft2232_execute_command(cmd) != ERROR_OK)
retval = ERROR_JTAG_QUEUE_FAILED;
- /* Start reading input before FT2232 TX buffer fills up */
+ /* Start reading input before FT2232 TX buffer fills up.
+ * Sometimes this happens because we don't know the
+ * length of the last command before we execute it. So
+ * we simple inform the user.
+ */
cmd = cmd->next;
- if (ft2232_expect_read > 256)
+
+ if (ft2232_expect_read >= FT2232_BUFFER_READ_QUEUE_SIZE )
{
+ if (ft2232_expect_read > (FT2232_BUFFER_READ_QUEUE_SIZE+1) )
+ LOG_DEBUG("read buffer size looks too high %d/%d",ft2232_expect_read,(FT2232_BUFFER_READ_QUEUE_SIZE+1));
if (ft2232_send_and_recv(first_unsent, cmd) != ERROR_OK)
retval = ERROR_JTAG_QUEUE_FAILED;
first_unsent = cmd;
char* openex_string = NULL;
uint8_t latency_timer;
- LOG_DEBUG("'ft2232' interface using FTD2XX with '%s' layout (%4.4x:%4.4x)", ft2232_layout, vid, pid);
+ if (layout == NULL) {
+ LOG_WARNING("No ft2232 layout specified'");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+ LOG_DEBUG("'ft2232' interface using FTD2XX with '%s' layout (%4.4x:%4.4x)", layout->name, vid, pid);
#if IS_WIN32 == 0
/* Add non-standard Vid/Pid to the linux driver */
} else {
/* drat, give the user a meaningfull message.
* telling the use we tried *BOTH* methods. */
- LOG_WARNING("Unable to open FTDI Device tried: '%s' and '%s'\n",
+ LOG_WARNING("Unable to open FTDI Device tried: '%s' and '%s'",
ft2232_device_desc,
ft2232_device_desc_A);
}
if (more)
{
- LOG_WARNING("unable to open ftdi device (trying more): %lu", status);
+ LOG_WARNING("unable to open ftdi device (trying more): %s",
+ ftd2xx_status_string(status));
*try_more = 1;
return ERROR_JTAG_INIT_FAILED;
}
- LOG_ERROR("unable to open ftdi device: %lu", status);
+ LOG_ERROR("unable to open ftdi device: %s",
+ ftd2xx_status_string(status));
status = FT_ListDevices(&num_devices, NULL, FT_LIST_NUMBER_ONLY);
if (status == FT_OK)
{
if (status == FT_OK)
{
- LOG_ERROR("ListDevices: %lu\n", num_devices);
+ LOG_ERROR("ListDevices: %" PRIu32, (uint32_t)num_devices);
for (i = 0; i < num_devices; i++)
LOG_ERROR("%" PRIu32 ": \"%s\"", i, desc_array[i]);
}
}
else
{
- LOG_ERROR("ListDevices: NONE\n");
+ LOG_ERROR("ListDevices: NONE");
}
return ERROR_JTAG_INIT_FAILED;
}
if ((status = FT_SetLatencyTimer(ftdih, ft2232_latency)) != FT_OK)
{
- LOG_ERROR("unable to set latency timer: %lu", status);
+ LOG_ERROR("unable to set latency timer: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_INIT_FAILED;
}
if ((status = FT_GetLatencyTimer(ftdih, &latency_timer)) != FT_OK)
{
- LOG_ERROR("unable to get latency timer: %lu", status);
- return ERROR_JTAG_INIT_FAILED;
+ /* ftd2xx 1.04 (linux) has a bug when calling FT_GetLatencyTimer
+ * so ignore errors if using this driver version */
+ DWORD dw_version;
+
+ status = FT_GetDriverVersion(ftdih, &dw_version);
+ LOG_ERROR("unable to get latency timer: %s",
+ ftd2xx_status_string(status));
+
+ if ((status == FT_OK) && (dw_version == 0x10004)) {
+ LOG_ERROR("ftd2xx 1.04 detected - this has known issues " \
+ "with FT_GetLatencyTimer, upgrade to a newer version");
+ }
+ else {
+ return ERROR_JTAG_INIT_FAILED;
+ }
}
else
{
if ((status = FT_SetTimeouts(ftdih, 5000, 5000)) != FT_OK)
{
- LOG_ERROR("unable to set timeouts: %lu", status);
+ LOG_ERROR("unable to set timeouts: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_INIT_FAILED;
}
if ((status = FT_SetBitMode(ftdih, 0x0b, 2)) != FT_OK)
{
- LOG_ERROR("unable to enable bit i/o mode: %lu", status);
+ LOG_ERROR("unable to enable bit i/o mode: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_INIT_FAILED;
}
if ((status = FT_GetDeviceInfo(ftdih, &ftdi_device, &deviceID, SerialNumber, Description, NULL)) != FT_OK)
{
- LOG_ERROR("unable to get FT_GetDeviceInfo: %lu", status);
+ LOG_ERROR("unable to get FT_GetDeviceInfo: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_INIT_FAILED;
}
else
unsigned no_of_known_types = ARRAY_SIZE(type_str) - 1;
unsigned type_index = ((unsigned)ftdi_device <= no_of_known_types)
? ftdi_device : FT_DEVICE_UNKNOWN;
- LOG_INFO("device: %lu \"%s\"", ftdi_device, type_str[type_index]);
- LOG_INFO("deviceID: %lu", deviceID);
+ LOG_INFO("device: %" PRIu32 " \"%s\"", (uint32_t)ftdi_device, type_str[type_index]);
+ LOG_INFO("deviceID: %" PRIu32, (uint32_t)deviceID);
LOG_INFO("SerialNumber: %s", SerialNumber);
LOG_INFO("Description: %s", Description);
}
if ((status = FT_Purge(ftdih, FT_PURGE_RX | FT_PURGE_TX)) != FT_OK)
{
- LOG_ERROR("error purging ftd2xx device: %lu", status);
+ LOG_ERROR("error purging ftd2xx device: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_INIT_FAILED;
}
#endif /* BUILD_FT2232_FTD2XX == 1 */
#if BUILD_FT2232_LIBFTDI == 1
-static int ft2232_init_libftdi(uint16_t vid, uint16_t pid, int more, int* try_more)
+static int ft2232_init_libftdi(uint16_t vid, uint16_t pid, int more, int* try_more, int channel)
{
uint8_t latency_timer;
+ if (layout == NULL) {
+ LOG_WARNING("No ft2232 layout specified'");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
LOG_DEBUG("'ft2232' interface using libftdi with '%s' layout (%4.4x:%4.4x)",
- ft2232_layout, vid, pid);
+ layout->name, vid, pid);
if (ftdi_init(&ftdic) < 0)
return ERROR_JTAG_INIT_FAILED;
- if (ftdi_set_interface(&ftdic, INTERFACE_A) < 0)
+ /* default to INTERFACE_A */
+ if(channel == INTERFACE_ANY) { channel = INTERFACE_A; }
+
+ if (ftdi_set_interface(&ftdic, channel) < 0)
{
LOG_ERROR("unable to select FT2232 channel A: %s", ftdic.error_str);
return ERROR_JTAG_INIT_FAILED;
#endif /* BUILD_FT2232_LIBFTDI == 1 */
+static int ft2232_set_data_bits_low_byte( uint8_t value, uint8_t direction )
+{
+ uint8_t buf[3];
+ uint32_t bytes_written;
+
+ buf[0] = 0x80; /* command "set data bits low byte" */
+ buf[1] = value; /* value */
+ buf[2] = direction; /* direction */
+
+ LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
+
+ if (ft2232_write(buf, sizeof(buf), &bytes_written) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't initialize data bits low byte");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+ return ERROR_OK;
+}
+
+static int ft2232_set_data_bits_high_byte( uint8_t value, uint8_t direction )
+{
+ uint8_t buf[3];
+ uint32_t bytes_written;
+
+ buf[0] = 0x82; /* command "set data bits high byte" */
+ buf[1] = value; /* value */
+ buf[2] = direction; /* direction */
+
+ LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
+
+ if (ft2232_write(buf, sizeof(buf), &bytes_written) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't initialize data bits high byte");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+ return ERROR_OK;
+}
+
static int ft2232_init(void)
{
uint8_t buf[1];
int retval;
uint32_t bytes_written;
- const struct ft2232_layout* cur_layout = ft2232_layouts;
- int i;
if (tap_get_tms_path_len(TAP_IRPAUSE,TAP_IRPAUSE) == 7)
{
LOG_DEBUG("ft2232 interface using shortest path jtag state transitions");
}
- if ((ft2232_layout == NULL) || (ft2232_layout[0] == 0))
- {
- ft2232_layout = "usbjtag";
- LOG_WARNING("No ft2232 layout specified, using default 'usbjtag'");
- }
-
- while (cur_layout->name)
- {
- if (strcmp(cur_layout->name, ft2232_layout) == 0)
- {
- layout = cur_layout;
- break;
- }
- cur_layout++;
- }
-
- if (!layout)
- {
- LOG_ERROR("No matching layout found for %s", ft2232_layout);
+ if (layout == NULL) {
+ LOG_WARNING("No ft2232 layout specified'");
return ERROR_JTAG_INIT_FAILED;
}
- for (i = 0; 1; i++)
+ for (int i = 0; 1; i++)
{
/*
* "more indicates that there are more IDs to try, so we should
more, &try_more);
#elif BUILD_FT2232_LIBFTDI == 1
retval = ft2232_init_libftdi(ft2232_vid[i], ft2232_pid[i],
- more, &try_more);
+ more, &try_more, layout->channel);
#endif
if (retval >= 0)
break;
return ERROR_JTAG_INIT_FAILED;
}
- ft2232_speed(jtag_get_speed());
-
buf[0] = 0x85; /* Disconnect TDI/DO to TDO/DI for Loopback */
- if (((retval = ft2232_write(buf, 1, &bytes_written)) != ERROR_OK) || (bytes_written != 1))
+ if ((retval = ft2232_write(buf, 1, &bytes_written)) != ERROR_OK)
{
LOG_ERROR("couldn't write to FT2232 to disable loopback");
return ERROR_JTAG_INIT_FAILED;
return ERROR_OK;
}
-static int usbjtag_init(void)
+/** Updates defaults for DBUS signals: the four JTAG signals
+ * (TCK, TDI, TDO, TMS) and * the four GPIOL signals.
+ */
+static inline void ftx232_dbus_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
-
low_output = 0x08;
low_direction = 0x0b;
+}
- if (strcmp(ft2232_layout, "usbjtag") == 0)
- {
- nTRST = 0x10;
- nTRSTnOE = 0x10;
- nSRST = 0x40;
- nSRSTnOE = 0x40;
- }
- else if (strcmp(ft2232_layout, "signalyzer") == 0)
- {
- nTRST = 0x10;
- nTRSTnOE = 0x10;
- nSRST = 0x20;
- nSRSTnOE = 0x20;
- }
- else if (strcmp(ft2232_layout, "evb_lm3s811") == 0)
- {
- nTRST = 0x0;
- nTRSTnOE = 0x00;
- nSRST = 0x20;
- nSRSTnOE = 0x20;
- low_output = 0x88;
- low_direction = 0x8b;
- }
- else if (strcmp(ft2232_layout, "luminary_icdi") == 0)
- {
- nTRST = 0x0;
- nTRSTnOE = 0x00;
- nSRST = 0x20;
- nSRSTnOE = 0x20;
- low_output = 0x88;
- low_direction = 0xcb;
- }
- else
- {
- LOG_ERROR("BUG: usbjtag_init called for unknown layout '%s'", ft2232_layout);
- return ERROR_JTAG_INIT_FAILED;
- }
-
+/** Initializes DBUS signals: the four JTAG signals (TCK, TDI, TDO, TMS),
+ * the four GPIOL signals. Initialization covers value and direction,
+ * as customized for each layout.
+ */
+static int ftx232_dbus_write(void)
+{
enum reset_types jtag_reset_config = jtag_get_reset_config();
if (jtag_reset_config & RESET_TRST_OPEN_DRAIN)
{
}
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output; /* value (TMS = 1,TCK = 0, TDI = 0, xRST high) */
- buf[2] = low_direction; /* dir (output = 1), TCK/TDI/TMS = out, TDO = in */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
- LOG_ERROR("couldn't initialize FT2232 with 'USBJTAG' layout");
+ LOG_ERROR("couldn't initialize FT2232 DBUS");
return ERROR_JTAG_INIT_FAILED;
}
return ERROR_OK;
}
-static int axm0432_jtag_init(void)
+static int usbjtag_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
+ /*
+ * NOTE: This is now _specific_ to the "usbjtag" layout.
+ * Don't try cram any more layouts into this.
+ */
+ ftx232_dbus_init();
- low_output = 0x08;
+ nTRST = 0x10;
+ nTRSTnOE = 0x10;
+ nSRST = 0x40;
+ nSRSTnOE = 0x40;
+
+ return ftx232_dbus_write();
+}
+
+static int lm3s811_jtag_init(void)
+{
+ ftx232_dbus_init();
+
+ /* There are multiple revisions of LM3S811 eval boards:
+ * - Rev B (and older?) boards have no SWO trace support.
+ * - Rev C boards add ADBUS_6 DBG_ENn and BDBUS_4 SWO_EN;
+ * they should use the "luminary_icdi" layout instead.
+ */
+ nTRST = 0x0;
+ nTRSTnOE = 0x00;
+ nSRST = 0x20;
+ nSRSTnOE = 0x20;
+ low_output = 0x88;
+ low_direction = 0x8b;
+
+ return ftx232_dbus_write();
+}
+
+static int icdi_jtag_init(void)
+{
+ ftx232_dbus_init();
+
+ /* Most Luminary eval boards support SWO trace output,
+ * and should use this "luminary_icdi" layout.
+ *
+ * ADBUS 0..3 are used for JTAG as usual. GPIOs are used
+ * to switch between JTAG and SWD, or switch the ft2232 UART
+ * on the second MPSSE channel/interface (BDBUS)
+ * between (i) the stellaris UART (on Luminary boards)
+ * or (ii) SWO trace data (generic).
+ *
+ * We come up in JTAG mode and may switch to SWD later (with
+ * SWO/trace option if SWD is active).
+ *
+ * DBUS == GPIO-Lx
+ * CBUS == GPIO-Hx
+ */
+
+
+#define ICDI_JTAG_EN (1 << 7) /* ADBUS 7 (a.k.a. DBGMOD) */
+#define ICDI_DBG_ENn (1 << 6) /* ADBUS 6 */
+#define ICDI_SRST (1 << 5) /* ADBUS 5 */
+
+
+ /* GPIOs on second channel/interface (UART) ... */
+#define ICDI_SWO_EN (1 << 4) /* BDBUS 4 */
+#define ICDI_TX_SWO (1 << 1) /* BDBUS 1 */
+#define ICDI_VCP_RX (1 << 0) /* BDBUS 0 (to stellaris UART) */
+
+ nTRST = 0x0;
+ nTRSTnOE = 0x00;
+ nSRST = ICDI_SRST;
+ nSRSTnOE = ICDI_SRST;
+
+ low_direction |= ICDI_JTAG_EN | ICDI_DBG_ENn;
+ low_output |= ICDI_JTAG_EN;
+ low_output &= ~ICDI_DBG_ENn;
+
+ return ftx232_dbus_write();
+}
+
+static int signalyzer_init(void)
+{
+ ftx232_dbus_init();
+
+ nTRST = 0x10;
+ nTRSTnOE = 0x10;
+ nSRST = 0x20;
+ nSRSTnOE = 0x20;
+ return ftx232_dbus_write();
+}
+
+static int axm0432_jtag_init(void)
+{
+ low_output = 0x08;
low_direction = 0x2b;
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output; /* value (TMS = 1,TCK = 0, TDI = 0, nOE = 0) */
- buf[2] = low_direction; /* dir (output = 1), TCK/TDI/TMS = out, TDO = in, nOE = out */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'JTAGkey' layout");
return ERROR_JTAG_INIT_FAILED;
high_output |= nSRST;
}
- /* initialize high port */
- buf[0] = 0x82; /* command "set data bits high byte" */
- buf[1] = high_output; /* value */
- buf[2] = high_direction; /* all outputs (xRST and xRSTnOE) */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'Dicarlo' layout");
return ERROR_JTAG_INIT_FAILED;
return ERROR_OK;
}
-static int jtagkey_init(void)
+static int redbee_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
+ low_output = 0x08;
+ low_direction = 0x2b;
+ /* initialize low byte for jtag */
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't initialize FT2232 with 'redbee' layout");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+ nTRST = 0x08;
+ nTRSTnOE = 0x0; /* No output enable for TRST*/
+ nSRST = 0x04;
+ nSRSTnOE = 0x0; /* No output enable for SRST*/
+
+ high_output = 0x0;
+ high_direction = 0x0c;
+
+ enum reset_types jtag_reset_config = jtag_get_reset_config();
+ if (jtag_reset_config & RESET_TRST_OPEN_DRAIN)
+ {
+ LOG_ERROR("can't set nTRSTOE to push-pull on redbee");
+ }
+ else
+ {
+ high_output |= nTRST;
+ }
+
+ if (jtag_reset_config & RESET_SRST_PUSH_PULL)
+ {
+ LOG_ERROR("can't set nSRST to push-pull on redbee");
+ }
+ else
+ {
+ high_output |= nSRST;
+ }
+
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't initialize FT2232 with 'redbee' layout");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+ return ERROR_OK;
+}
+
+static int jtagkey_init(void)
+{
low_output = 0x08;
low_direction = 0x1b;
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output; /* value (TMS = 1,TCK = 0, TDI = 0, nOE = 0) */
- buf[2] = low_direction; /* dir (output = 1), TCK/TDI/TMS = out, TDO = in, nOE = out */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'JTAGkey' layout");
return ERROR_JTAG_INIT_FAILED;
high_output &= ~nSRST;
}
- /* initialize high port */
- buf[0] = 0x82; /* command "set data bits high byte" */
- buf[1] = high_output; /* value */
- buf[2] = high_direction; /* all outputs (xRST and xRSTnOE) */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'JTAGkey' layout");
return ERROR_JTAG_INIT_FAILED;
static int olimex_jtag_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
-
low_output = 0x08;
low_direction = 0x1b;
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output; /* value (TMS = 1,TCK = 0, TDI = 0, nOE = 0) */
- buf[2] = low_direction; /* dir (output = 1), TCK/TDI/TMS = out, TDO = in, nOE = out */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'Olimex' layout");
return ERROR_JTAG_INIT_FAILED;
/* turn red LED on */
high_output |= 0x08;
- /* initialize high port */
- buf[0] = 0x82; /* command "set data bits high byte" */
- buf[1] = high_output; /* value */
- buf[2] = high_direction; /* all outputs (xRST and xRSTnOE) */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if ((ft2232_write(buf, 3, &bytes_written) != ERROR_OK) || (bytes_written != 3))
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'Olimex' layout");
return ERROR_JTAG_INIT_FAILED;
static int flyswatter_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
-
low_output = 0x18;
low_direction = 0xfb;
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output; /* value (TMS = 1,TCK = 0, TDI = 0, nOE = 0) */
- buf[2] = low_direction; /* dir (output = 1), TCK/TDI/TMS = out, TDO = in, nOE[12]=out, n[ST]srst = out */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'flyswatter' layout");
return ERROR_JTAG_INIT_FAILED;
/* turn red LED3 on, LED2 off */
high_output |= 0x08;
- /* initialize high port */
- buf[0] = 0x82; /* command "set data bits high byte" */
- buf[1] = high_output; /* value */
- buf[2] = high_direction; /* all outputs (xRST and xRSTnOE) */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'flyswatter' layout");
return ERROR_JTAG_INIT_FAILED;
return ERROR_OK;
}
-static int turtle_init(void)
+static int minimodule_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
+ low_output = 0x18;//check if srst should be 1 or 0 initially. (0x08) (flyswatter was 0x18)
+ low_direction = 0xfb;//0xfb;
+ /* initialize low byte for jtag */
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't initialize FT2232 with 'minimodule' layout");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+
+ nSRST = 0x20;
+
+ high_output = 0x00;
+ high_direction = 0x05;
+
+ /* turn red LED3 on, LED2 off */
+ //high_output |= 0x08;
+
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't initialize FT2232 with 'minimodule' layout");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+ return ERROR_OK;
+}
+
+static int turtle_init(void)
+{
low_output = 0x08;
low_direction = 0x5b;
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output; /* value (TMS = 1,TCK = 0, TDI = 0, nOE = 0) */
- buf[2] = low_direction; /* dir (output = 1), TCK/TDI/TMS = out, TDO = in, nOE = out */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'turtelizer2' layout");
return ERROR_JTAG_INIT_FAILED;
high_output = 0x00;
high_direction = 0x0C;
- /* initialize high port */
- buf[0] = 0x82; /* command "set data bits high byte" */
- buf[1] = high_output;
- buf[2] = high_direction;
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'turtelizer2' layout");
return ERROR_JTAG_INIT_FAILED;
static int comstick_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
-
low_output = 0x08;
low_direction = 0x0b;
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output; /* value (TMS = 1,TCK = 0, TDI = 0, nOE = 0) */
- buf[2] = low_direction; /* dir (output = 1), TCK/TDI/TMS = out, TDO = in, nOE = out */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'comstick' layout");
return ERROR_JTAG_INIT_FAILED;
high_output = 0x03;
high_direction = 0x03;
- /* initialize high port */
- buf[0] = 0x82; /* command "set data bits high byte" */
- buf[1] = high_output;
- buf[2] = high_direction;
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'comstick' layout");
return ERROR_JTAG_INIT_FAILED;
static int stm32stick_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
-
low_output = 0x88;
low_direction = 0x8b;
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output; /* value (TMS = 1,TCK = 0, TDI = 0, nOE = 0) */
- buf[2] = low_direction; /* dir (output = 1), TCK/TDI/TMS = out, TDO = in, nOE = out */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'stm32stick' layout");
return ERROR_JTAG_INIT_FAILED;
high_output = 0x01;
high_direction = 0x03;
- /* initialize high port */
- buf[0] = 0x82; /* command "set data bits high byte" */
- buf[1] = high_output;
- buf[2] = high_direction;
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'stm32stick' layout");
return ERROR_JTAG_INIT_FAILED;
static int sheevaplug_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
-
low_output = 0x08;
low_direction = 0x1b;
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output; /* value (TMS = 1,TCK = 0, TDI = 0, nOE = 0) */
- buf[2] = low_direction; /* dir (output = 1), TCK/TDI/TMS = out, TDO = in */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'sheevaplug' layout");
return ERROR_JTAG_INIT_FAILED;
high_output |= nSRSTnOE;
high_output &= ~nSRST;
- /* initialize high port */
- buf[0] = 0x82; /* command "set data bits high byte" */
- buf[1] = high_output; /* value */
- buf[2] = high_direction; /* all outputs - xRST */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'sheevaplug' layout");
return ERROR_JTAG_INIT_FAILED;
static int cortino_jtag_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
-
low_output = 0x08;
low_direction = 0x1b;
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output; /* value (TMS = 1,TCK = 0, TDI = 0, nOE = 0) */
- buf[2] = low_direction; /* dir (output = 1), TCK/TDI/TMS = out, TDO = in, nOE = out */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'cortino' layout");
return ERROR_JTAG_INIT_FAILED;
high_output = 0x03;
high_direction = 0x03;
- /* initialize high port */
- buf[0] = 0x82; /* command "set data bits high byte" */
- buf[1] = high_output;
- buf[2] = high_direction;
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't initialize FT2232 with 'cortino' layout");
+ return ERROR_JTAG_INIT_FAILED;
+ }
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ return ERROR_OK;
+}
+
+static int lisa_l_init(void)
+{
+ ftx232_dbus_init();
+
+ nTRST = 0x10;
+ nTRSTnOE = 0x10;
+ nSRST = 0x40;
+ nSRSTnOE = 0x40;
+
+ high_output = 0x00;
+ high_direction = 0x18;
+
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
- LOG_ERROR("couldn't initialize FT2232 with 'stm32stick' layout");
+ LOG_ERROR("couldn't initialize FT2232 with 'lisa_l' layout");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+ return ftx232_dbus_write();
+}
+
+static int flossjtag_init(void)
+{
+ ftx232_dbus_init();
+
+ nTRST = 0x10;
+ nTRSTnOE = 0x10;
+ nSRST = 0x40;
+ nSRSTnOE = 0x40;
+
+ high_output = 0x00;
+ high_direction = 0x18;
+
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't initialize FT2232 with 'Floss-JTAG' layout");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+ return ftx232_dbus_write();
+}
+
+/*
+ * The reference schematic from TI for the XDS100v2 has a CPLD on which opens
+ * the door for a number of different configurations
+ *
+ * Known Implementations:
+ * http://processors.wiki.ti.com/images/9/93/TMS570LS20216_USB_STICK_Schematic.pdf
+ *
+ * http://processors.wiki.ti.com/index.php/XDS100 (rev2)
+ * * CLPD logic: Rising edge to enable outputs (XDS100_PWR_RST)
+ * * ACBUS3 to transition 0->1 (OE rising edge)
+ * * CPLD logic: Put the EMU0/1 pins in Hi-Z:
+ * * ADBUS5/GPIOL1 = EMU_EN = 1
+ * * ADBUS6/GPIOL2 = EMU0 = 0
+ * * ACBUS4/SPARE0 = EMU1 = 0
+ * * CPLD logic: Disable loopback
+ * * ACBUS6/SPARE2 = LOOPBACK = 0
+ */
+#define XDS100_nEMU_EN (1<<5)
+#define XDS100_nEMU0 (1<<6)
+
+#define XDS100_PWR_RST (1<<3)
+#define XDS100_nEMU1 (1<<4)
+#define XDS100_LOOPBACK (1<<6)
+static int xds100v2_init(void)
+{
+ /* These are in the lower byte */
+ nTRST = 0x10;
+ nTRSTnOE = 0x10;
+
+ /* These aren't actually used on 14 pin connectors */
+ /* These are in the upper byte */
+ nSRST = 0x01;
+ nSRSTnOE = 0x01;
+
+ low_output = 0x08 | nTRST | XDS100_nEMU_EN;
+ low_direction = 0x0b | nTRSTnOE | XDS100_nEMU_EN | XDS100_nEMU0;
+
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't initialize FT2232 with 'xds100v2' layout");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+ high_output = 0;
+ high_direction = nSRSTnOE | XDS100_LOOPBACK | XDS100_PWR_RST | XDS100_nEMU1;
+
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't put CPLD in to reset with 'xds100v2' layout");
+ return ERROR_JTAG_INIT_FAILED;
+ }
+
+ high_output |= XDS100_PWR_RST;
+
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
+ {
+ LOG_ERROR("couldn't bring CPLD out of reset with 'xds100v2' layout");
return ERROR_JTAG_INIT_FAILED;
}
/* Olimex ARM-USB-OCD has a LED connected to ACBUS3
* ACBUS3 is bit 3 of the GPIOH port
*/
- if (high_output & 0x08)
- {
- /* set port pin high */
- high_output &= 0x07;
- }
- else
- {
- /* set port pin low */
- high_output |= 0x08;
- }
+ high_output ^= 0x08;
buffer_write(0x82);
buffer_write(high_output);
buffer_write(high_direction);
}
+static void lisa_l_blink(void)
+{
+ /*
+ * Lisa/L has two LEDs connected to BCBUS3 and BCBUS4
+ */
+ if (high_output & 0x10)
+ {
+ high_output = 0x08;
+ }
+ else
+ {
+ high_output = 0x10;
+ }
+
+ buffer_write(0x82);
+ buffer_write(high_output);
+ buffer_write(high_direction);
+}
+
+static void flossjtag_blink(void)
+{
+ /*
+ * Floss-JTAG has two LEDs connected to ACBUS3 and ACBUS4
+ */
+ if (high_output & 0x10)
+ {
+ high_output = 0x08;
+ }
+ else
+ {
+ high_output = 0x10;
+ }
+
+ buffer_write(0x82);
+ buffer_write(high_output);
+ buffer_write(high_direction);
+}
+
static int ft2232_quit(void)
{
#if BUILD_FT2232_FTD2XX == 1
COMMAND_HANDLER(ft2232_handle_layout_command)
{
- if (CMD_ARGC == 0)
- return ERROR_OK;
+ if (CMD_ARGC != 1) {
+ LOG_ERROR("Need exactly one argument to ft2232_layout");
+ return ERROR_FAIL;
+ }
- ft2232_layout = malloc(strlen(CMD_ARGV[0]) + 1);
- strcpy(ft2232_layout, CMD_ARGV[0]);
+ if (layout) {
+ LOG_ERROR("already specified ft2232_layout %s",
+ layout->name);
+ return (strcmp(layout->name, CMD_ARGV[0]) != 0)
+ ? ERROR_FAIL
+ : ERROR_OK;
+ }
- return ERROR_OK;
+ for (const struct ft2232_layout *l = ft2232_layouts; l->name; l++) {
+ if (strcmp(l->name, CMD_ARGV[0]) == 0) {
+ layout = l;
+ return ERROR_OK;
+ }
+ }
+
+ LOG_ERROR("No FT2232 layout '%s' found", CMD_ARGV[0]);
+ return ERROR_FAIL;
}
COMMAND_HANDLER(ft2232_handle_vid_pid_command)
* ADBUS7 - GND
*/
static int icebear_jtag_init(void) {
- uint8_t buf[3];
- uint32_t bytes_written;
-
low_direction = 0x0b; /* output: TCK TDI TMS; input: TDO */
low_output = 0x08; /* high: TMS; low: TCK TDI */
nTRST = 0x10;
low_output |= nSRST;
/* initialize low byte for jtag */
- buf[0] = 0x80; /* command "set data bits low byte" */
- buf[1] = low_output;
- buf[2] = low_direction;
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3)) {
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK) {
LOG_ERROR("couldn't initialize FT2232 with 'IceBear' layout (low)");
return ERROR_JTAG_INIT_FAILED;
}
high_output = 0x0;
high_direction = 0x00;
-
- /* initialize high port */
- buf[0] = 0x82; /* command "set data bits high byte" */
- buf[1] = high_output; /* value */
- buf[2] = high_direction; /* all outputs (xRST and xRSTnOE) */
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3)) {
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK) {
LOG_ERROR("couldn't initialize FT2232 with 'IceBear' layout (high)");
return ERROR_JTAG_INIT_FAILED;
}
if ((status = signalyzer_h_ctrl_write(SIGNALYZER_DATA_BUFFER_ADDR,
((uint32_t)(channel << 8) | led))) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
(SIGNALYZER_DATA_BUFFER_ADDR + 1),
((uint32_t)(on_time << 8) | off_time))) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
(SIGNALYZER_DATA_BUFFER_ADDR + 2),
((uint32_t)cycles))) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
if ((status = signalyzer_h_ctrl_write(SIGNALYZER_COMMAND_ADDR,
SIGNALYZER_COMMAND_LED_SET)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
char *end_of_desc;
uint16_t read_buf[12] = { 0 };
- uint8_t buf[3];
- uint32_t bytes_written;
/* turn on center green led */
signalyzer_h_led_set(SIGNALYZER_CHAN_C, SIGNALYZER_LED_GREEN,
if ((status = signalyzer_h_ctrl_write(SIGNALYZER_COMMAND_ADDR,
SIGNALYZER_COMMAND_VERSION)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
(SIGNALYZER_DATA_BUFFER_ADDR + i),
&read_buf[i])) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_read returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_read returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
}
if ((status = signalyzer_h_ctrl_write(SIGNALYZER_DATA_BUFFER_ADDR,
(uint32_t)(signalyzer_h_side << 8))) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
if ((status = signalyzer_h_ctrl_write(SIGNALYZER_DATA_BUFFER_ADDR + 1,
0x0404)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
if ((status = signalyzer_h_ctrl_write(SIGNALYZER_COMMAND_ADDR,
SIGNALYZER_COMMAND_GPIO_STATE)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
if ((status = signalyzer_h_ctrl_write(SIGNALYZER_DATA_BUFFER_ADDR,
((uint32_t)(signalyzer_h_side << 8) | 0x01))) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
if ((status = signalyzer_h_ctrl_write(
(SIGNALYZER_DATA_BUFFER_ADDR + 1), 0xA000)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
if ((status = signalyzer_h_ctrl_write(
(SIGNALYZER_DATA_BUFFER_ADDR + 2), 0x0008)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
if ((status = signalyzer_h_ctrl_write(SIGNALYZER_COMMAND_ADDR,
SIGNALYZER_COMMAND_I2C)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
if ((status = signalyzer_h_ctrl_read(SIGNALYZER_COMMAND_ADDR,
&read_buf[0])) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_read returned: %lu", status);
+ LOG_ERROR("signalyzer_h_ctrl_read returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
(SIGNALYZER_DATA_BUFFER_ADDR + i),
&read_buf[i])) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_read returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_read returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
}
((uint32_t)(signalyzer_h_side << 8) | 0x01)))
!= FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
if ((status = signalyzer_h_ctrl_write(SIGNALYZER_COMMAND_ADDR,
SIGNALYZER_COMMAND_POWERCONTROL_SET)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_DATA_BUFFER_ADDR,
(uint32_t)(signalyzer_h_side << 8))) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_DATA_BUFFER_ADDR + 1, 0x0000))
!= FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
if ((status = signalyzer_h_ctrl_write(SIGNALYZER_COMMAND_ADDR,
SIGNALYZER_COMMAND_GPIO_MODE)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_DATA_BUFFER_ADDR,
(uint32_t)(signalyzer_h_side << 8))) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_DATA_BUFFER_ADDR + 1, 0x4040))
!= FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_COMMAND_ADDR,
SIGNALYZER_COMMAND_GPIO_STATE)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
#endif
((uint32_t)(signalyzer_h_side << 8) | 0x01)))
!= FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_COMMAND_ADDR,
SIGNALYZER_COMMAND_POWERCONTROL_SET)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_DATA_BUFFER_ADDR,
(uint32_t)(signalyzer_h_side << 8))) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_DATA_BUFFER_ADDR + 1, 0x0060))
!= FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_COMMAND_ADDR,
SIGNALYZER_COMMAND_GPIO_MODE)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_DATA_BUFFER_ADDR,
(uint32_t)(signalyzer_h_side << 8))) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_DATA_BUFFER_ADDR + 1, 0x0000))
!= FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
SIGNALYZER_COMMAND_ADDR,
SIGNALYZER_COMMAND_GPIO_STATE)) != FT_OK)
{
- LOG_ERROR("signalyzer_h_ctrl_write returned: %lu",
- status);
+ LOG_ERROR("signalyzer_h_ctrl_write returned: %s",
+ ftd2xx_status_string(status));
return ERROR_JTAG_DEVICE_ERROR;
}
#endif
}
/* initialize low byte of controller for jtag operation */
- buf[0] = 0x80;
- buf[1] = low_output;
- buf[2] = low_direction;
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK)
- || (bytes_written != 3))
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize Signalyzer-H layout");
return ERROR_JTAG_INIT_FAILED;
if (ftdi_device == FT_DEVICE_2232H)
{
/* initialize high byte of controller for jtag operation */
- buf[0] = 0x82;
- buf[1] = high_output;
- buf[2] = high_direction;
-
- if ((ft2232_write(buf, 3, &bytes_written) != ERROR_OK)
- || (bytes_written != 3))
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize Signalyzer-H layout");
return ERROR_JTAG_INIT_FAILED;
if (ftdi_device == TYPE_2232H)
{
/* initialize high byte of controller for jtag operation */
- buf[0] = 0x82;
- buf[1] = high_output;
- buf[2] = high_direction;
-
- if ((ft2232_write(buf, 3, &bytes_written) != ERROR_OK)
- || (bytes_written != 3))
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize Signalyzer-H layout");
return ERROR_JTAG_INIT_FAILED;
*******************************************************************/
static int ktlink_init(void)
{
- uint8_t buf[3];
- uint32_t bytes_written;
uint8_t swd_en = 0x20; //0x20 SWD disable, 0x00 SWD enable (ADBUS5)
low_output = 0x08 | swd_en; // value; TMS=1,TCK=0,TDI=0,SWD=swd_en
low_direction = 0x3B; // out=1; TCK/TDI/TMS=out,TDO=in,SWD=out,RTCK=in,SRSTIN=in
- // initialize low port
- buf[0] = 0x80; // command "set data bits low byte"
- buf[1] = low_output;
- buf[2] = low_direction;
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ /* initialize low byte for jtag */
+ if (ft2232_set_data_bits_low_byte(low_output,low_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'ktlink' layout");
return ERROR_JTAG_INIT_FAILED;
high_output &= ~nSRST;
}
- // initialize high port
- buf[0] = 0x82; // command "set data bits high byte"
- buf[1] = high_output; // value
- buf[2] = high_direction;
- LOG_DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
-
- if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+ /* initialize high byte for jtag */
+ if (ft2232_set_data_bits_high_byte(high_output,high_direction) != ERROR_OK)
{
LOG_ERROR("couldn't initialize FT2232 with 'ktlink' layout");
return ERROR_JTAG_INIT_FAILED;
static void ktlink_blink(void)
{
/* LED connected to ACBUS7 */
- if (high_output & 0x80)
- high_output &= 0x7F;
- else
- high_output |= 0x80;
+ high_output ^= 0x80;
buffer_write(0x82); // command "set data bits high byte"
buffer_write(high_output);
.handler = &ft2232_handle_device_desc_command,
.mode = COMMAND_CONFIG,
.help = "set the USB device description of the FTDI FT2232 device",
- .usage = "<description>",
+ .usage = "description_string",
},
{
.name = "ft2232_serial",
.handler = &ft2232_handle_serial_command,
.mode = COMMAND_CONFIG,
.help = "set the serial number of the FTDI FT2232 device",
- .usage = "<serial#>",
+ .usage = "serial_string",
},
{
.name = "ft2232_layout",
.mode = COMMAND_CONFIG,
.help = "set the layout of the FT2232 GPIO signals used "
"to control output-enables and reset signals",
- .usage = "<layout>",
+ .usage = "layout_name",
},
{
.name = "ft2232_vid_pid",
.handler = &ft2232_handle_vid_pid_command,
.mode = COMMAND_CONFIG,
.help = "the vendor ID and product ID of the FTDI FT2232 device",
- .usage = "<vid> <pid> [...]",
+ .usage = "(vid pid)* ",
},
{
.name = "ft2232_latency",
.handler = &ft2232_handle_latency_command,
.mode = COMMAND_CONFIG,
.help = "set the FT2232 latency timer to a new value",
- .usage = "<vid> <pid> [...]",
+ .usage = "value",
},
COMMAND_REGISTRATION_DONE
};
struct jtag_interface ft2232_interface = {
- .name = "ft2232",
- .commands = ft2232_command_handlers,
- .init = &ft2232_init,
- .quit = &ft2232_quit,
- .speed = &ft2232_speed,
- .speed_div = &ft2232_speed_div,
- .khz = &ft2232_khz,
- .execute_queue = &ft2232_execute_queue,
- };
+ .name = "ft2232",
+ .supported = DEBUG_CAP_TMS_SEQ,
+ .commands = ft2232_command_handlers,
+ .transports = jtag_only,
+
+ .init = ft2232_init,
+ .quit = ft2232_quit,
+ .speed = ft2232_speed,
+ .speed_div = ft2232_speed_div,
+ .khz = ft2232_khz,
+ .execute_queue = ft2232_execute_queue,
+};