/***************************************************************************
* Copyright (C) 2007 by Dominic Rath *
* Dominic.Rath@gmx.de *
+ *
+ * Copyright (C) 2010 richard vegh <vegh.ricsi@gmail.com> *
+ * Copyright (C) 2010 Oyvind Harboe <oyvind.harboe@zylin.com> *
* *
* This program is free software; you can redistribute it and/or modify *
* it under the terms of the GNU General Public License as published by *
* Free Software Foundation, Inc., *
* 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. *
***************************************************************************/
+
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
#include "lpc3180.h"
#include <target/target.h>
-
static int lpc3180_reset(struct nand_device *nand);
static int lpc3180_controller_ready(struct nand_device *nand, int timeout);
+static int lpc3180_tc_ready(struct nand_device *nand, int timeout);
+
+#define ECC_OFFS 0x120
+#define SPARE_OFFS 0x140
+#define DATA_OFFS 0x200
/* nand device lpc3180 <target#> <oscillator_frequency>
*/
NAND_DEVICE_COMMAND_HANDLER(lpc3180_nand_device_command)
{
if (CMD_ARGC < 3)
- {
- LOG_WARNING("incomplete 'lpc3180' nand flash configuration");
- return ERROR_FLASH_BANK_INVALID;
- }
-
- struct target *target = get_target(CMD_ARGV[1]);
- if (NULL == target)
- {
- LOG_ERROR("target '%s' not defined", CMD_ARGV[1]);
- return ERROR_NAND_DEVICE_INVALID;
- }
+ return ERROR_COMMAND_SYNTAX_ERROR;
uint32_t osc_freq;
COMMAND_PARSE_NUMBER(u32, CMD_ARGV[2], osc_freq);
lpc3180_info = malloc(sizeof(struct lpc3180_nand_controller));
nand->controller_priv = lpc3180_info;
- lpc3180_info->target = target;
lpc3180_info->osc_freq = osc_freq;
if ((lpc3180_info->osc_freq < 1000) || (lpc3180_info->osc_freq > 20000))
- {
- LOG_WARNING("LPC3180 oscillator frequency should be between 1000 and 20000 kHz, was %i", lpc3180_info->osc_freq);
- }
+ LOG_WARNING(
+ "LPC3180 oscillator frequency should be between 1000 and 20000 kHz, was %i",
+ lpc3180_info->osc_freq);
lpc3180_info->selected_controller = LPC3180_NO_CONTROLLER;
lpc3180_info->sw_write_protection = 0;
lpc3180_info->sw_wp_lower_bound = 0x0;
return (m / (2 * p)) * (fclkin / n);
}
-static float lpc3180_cycle_time(struct lpc3180_nand_controller *lpc3180_info)
+static float lpc3180_cycle_time(struct nand_device *nand)
{
- struct target *target = lpc3180_info->target;
+ struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
+ struct target *target = nand->target;
uint32_t sysclk_ctrl, pwr_ctrl, hclkdiv_ctrl, hclkpll_ctrl;
int sysclk;
int hclk;
/* determine selected HCLK source */
target_read_u32(target, 0x40004044, &pwr_ctrl);
- if ((pwr_ctrl & (1 << 2)) == 0) /* DIRECT RUN mode */
- {
+ if ((pwr_ctrl & (1 << 2)) == 0) /* DIRECT RUN mode */
hclk = sysclk;
- }
- else
- {
+ else {
target_read_u32(target, 0x40004058, &hclkpll_ctrl);
hclk_pll = lpc3180_pll(sysclk, hclkpll_ctrl);
target_read_u32(target, 0x40004040, &hclkdiv_ctrl);
if (pwr_ctrl & (1 << 10)) /* ARM_CLK and HCLK use PERIPH_CLK */
- {
hclk = hclk_pll / (((hclkdiv_ctrl & 0x7c) >> 2) + 1);
- }
else /* HCLK uses HCLK_PLL */
- {
hclk = hclk_pll / (1 << (hclkdiv_ctrl & 0x3));
- }
}
LOG_DEBUG("LPC3180 HCLK currently clocked at %i kHz", hclk);
static int lpc3180_init(struct nand_device *nand)
{
struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
- struct target *target = lpc3180_info->target;
+ struct target *target = nand->target;
int bus_width = nand->bus_width ? : 8;
int address_cycles = nand->address_cycles ? : 3;
int page_size = nand->page_size ? : 512;
- if (target->state != TARGET_HALTED)
- {
+ if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
/* sanitize arguments */
- if ((bus_width != 8) && (bus_width != 16))
- {
+ if ((bus_width != 8) && (bus_width != 16)) {
LOG_ERROR("LPC3180 only supports 8 or 16 bit bus width, not %i", bus_width);
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
* would support 16 bit, too, so we just warn about this for now
*/
if (bus_width == 16)
- {
LOG_WARNING("LPC3180 only supports 8 bit bus width");
- }
/* inform calling code about selected bus width */
nand->bus_width = bus_width;
- if ((address_cycles != 3) && (address_cycles != 4))
- {
+ if ((address_cycles != 3) && (address_cycles != 4)) {
LOG_ERROR("LPC3180 only supports 3 or 4 address cycles, not %i", address_cycles);
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
- if ((page_size != 512) && (page_size != 2048))
- {
+ if ((page_size != 512) && (page_size != 2048)) {
LOG_ERROR("LPC3180 only supports 512 or 2048 byte pages, not %i", page_size);
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
/* select MLC controller if none is currently selected */
- if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER)
- {
+ if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER) {
LOG_DEBUG("no LPC3180 NAND flash controller selected, using default 'mlc'");
lpc3180_info->selected_controller = LPC3180_MLC_CONTROLLER;
}
- if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
- {
+ if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER) {
uint32_t mlc_icr_value = 0x0;
float cycle;
int twp, twh, trp, treh, trhz, trbwb, tcea;
target_write_u32(target, 0x200b8030, mlc_icr_value);
/* calculate NAND controller timings */
- cycle = lpc3180_cycle_time(lpc3180_info);
+ cycle = lpc3180_cycle_time(nand);
twp = ((40 / cycle) + 1);
twh = ((20 / cycle) + 1);
((trbwb & 0x1f) << 19) | ((tcea & 0x3) << 24));
lpc3180_reset(nand);
- }
- else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
float cycle;
int r_setup, r_hold, r_width, r_rdy;
int w_setup, w_hold, w_width, w_rdy;
/* FLASHCLK_CTRL = 0x05 (enable clock for SLC flash controller) */
target_write_u32(target, 0x400040c8, 0x05);
- /* SLC_CFG = 0x (Force nCE assert, ECC enabled, WIDTH = bus_width) */
- target_write_u32(target, 0x20020014, 0x28 | (bus_width == 16) ? 1 : 0);
+ /* after reset set other registers of SLC so reset calling is here at the begining*/
+ lpc3180_reset(nand);
+
+ /* SLC_CFG = 0x (Force nCE assert, DMA ECC enabled, ECC enabled, DMA burst enabled,
+ *DMA read from SLC, WIDTH = bus_width) */
+ target_write_u32(target, 0x20020014, 0x3e | (bus_width == 16) ? 1 : 0);
+
+ /* SLC_IEN = 3 (INT_RDY_EN = 1) ,(INT_TC_STAT = 1) */
+ target_write_u32(target, 0x20020020, 0x03);
+
+ /* DMA configuration
+ * DMACLK_CTRL = 0x01 (enable clock for DMA controller) */
+ target_write_u32(target, 0x400040e8, 0x01);
+ /* DMACConfig = DMA enabled*/
+ target_write_u32(target, 0x31000030, 0x01);
+
/* calculate NAND controller timings */
- cycle = lpc3180_cycle_time(lpc3180_info);
+ cycle = lpc3180_cycle_time(nand);
r_setup = w_setup = 0;
r_hold = w_hold = 10 / cycle;
((r_width & 0xf) << 8) | ((r_rdy & 0xf) << 12) | ((w_setup & 0xf) << 16) |
((w_hold & 0xf) << 20) | ((w_width & 0xf) << 24) | ((w_rdy & 0xf) << 28));
- lpc3180_reset(nand);
}
return ERROR_OK;
static int lpc3180_reset(struct nand_device *nand)
{
struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
- struct target *target = lpc3180_info->target;
+ struct target *target = nand->target;
- if (target->state != TARGET_HALTED)
- {
+ if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
- if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER)
- {
+ if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER) {
LOG_ERROR("BUG: no LPC3180 NAND flash controller selected");
return ERROR_NAND_OPERATION_FAILED;
- }
- else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER) {
/* MLC_CMD = 0xff (reset controller and NAND device) */
target_write_u32(target, 0x200b8000, 0xff);
- if (!lpc3180_controller_ready(nand, 100))
- {
+ if (!lpc3180_controller_ready(nand, 100)) {
LOG_ERROR("LPC3180 NAND controller timed out after reset");
return ERROR_NAND_OPERATION_TIMEOUT;
}
- }
- else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
/* SLC_CTRL = 0x6 (ECC_CLEAR, SW_RESET) */
target_write_u32(target, 0x20020010, 0x6);
- if (!lpc3180_controller_ready(nand, 100))
- {
+ if (!lpc3180_controller_ready(nand, 100)) {
LOG_ERROR("LPC3180 NAND controller timed out after reset");
return ERROR_NAND_OPERATION_TIMEOUT;
}
static int lpc3180_command(struct nand_device *nand, uint8_t command)
{
struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
- struct target *target = lpc3180_info->target;
+ struct target *target = nand->target;
- if (target->state != TARGET_HALTED)
- {
+ if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
- if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER)
- {
+ if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER) {
LOG_ERROR("BUG: no LPC3180 NAND flash controller selected");
return ERROR_NAND_OPERATION_FAILED;
- }
- else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER) {
/* MLC_CMD = command */
target_write_u32(target, 0x200b8000, command);
- }
- else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
/* SLC_CMD = command */
target_write_u32(target, 0x20020008, command);
}
static int lpc3180_address(struct nand_device *nand, uint8_t address)
{
struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
- struct target *target = lpc3180_info->target;
+ struct target *target = nand->target;
- if (target->state != TARGET_HALTED)
- {
+ if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
- if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER)
- {
+ if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER) {
LOG_ERROR("BUG: no LPC3180 NAND flash controller selected");
return ERROR_NAND_OPERATION_FAILED;
- }
- else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER) {
/* MLC_ADDR = address */
target_write_u32(target, 0x200b8004, address);
- }
- else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
/* SLC_ADDR = address */
target_write_u32(target, 0x20020004, address);
}
static int lpc3180_write_data(struct nand_device *nand, uint16_t data)
{
struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
- struct target *target = lpc3180_info->target;
+ struct target *target = nand->target;
- if (target->state != TARGET_HALTED)
- {
+ if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
- if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER)
- {
+ if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER) {
LOG_ERROR("BUG: no LPC3180 NAND flash controller selected");
return ERROR_NAND_OPERATION_FAILED;
- }
- else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER) {
/* MLC_DATA = data */
target_write_u32(target, 0x200b0000, data);
- }
- else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
/* SLC_DATA = data */
target_write_u32(target, 0x20020000, data);
}
static int lpc3180_read_data(struct nand_device *nand, void *data)
{
struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
- struct target *target = lpc3180_info->target;
+ struct target *target = nand->target;
- if (target->state != TARGET_HALTED)
- {
+ if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
- if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER)
- {
+ if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER) {
LOG_ERROR("BUG: no LPC3180 NAND flash controller selected");
return ERROR_NAND_OPERATION_FAILED;
- }
- else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER) {
/* data = MLC_DATA, use sized access */
- if (nand->bus_width == 8)
- {
+ if (nand->bus_width == 8) {
uint8_t *data8 = data;
target_read_u8(target, 0x200b0000, data8);
- }
- else if (nand->bus_width == 16)
- {
+ } else if (nand->bus_width == 16) {
uint16_t *data16 = data;
target_read_u16(target, 0x200b0000, data16);
- }
- else
- {
+ } else {
LOG_ERROR("BUG: bus_width neither 8 nor 16 bit");
return ERROR_NAND_OPERATION_FAILED;
}
- }
- else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER)
- {
+ } else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
uint32_t data32;
/* data = SLC_DATA, must use 32-bit access */
target_read_u32(target, 0x20020000, &data32);
- if (nand->bus_width == 8)
- {
+ if (nand->bus_width == 8) {
uint8_t *data8 = data;
*data8 = data32 & 0xff;
- }
- else if (nand->bus_width == 16)
- {
+ } else if (nand->bus_width == 16) {
uint16_t *data16 = data;
*data16 = data32 & 0xffff;
- }
- else
- {
+ } else {
LOG_ERROR("BUG: bus_width neither 8 nor 16 bit");
return ERROR_NAND_OPERATION_FAILED;
}
return ERROR_OK;
}
-static int lpc3180_write_page(struct nand_device *nand, uint32_t page, uint8_t *data, uint32_t data_size, uint8_t *oob, uint32_t oob_size)
+static int lpc3180_write_page(struct nand_device *nand,
+ uint32_t page,
+ uint8_t *data,
+ uint32_t data_size,
+ uint8_t *oob,
+ uint32_t oob_size)
{
struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
- struct target *target = lpc3180_info->target;
+ struct target *target = nand->target;
int retval;
uint8_t status;
+ uint8_t *page_buffer;
- if (target->state != TARGET_HALTED)
- {
+ if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
- if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER)
- {
+ if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER) {
LOG_ERROR("BUG: no LPC3180 NAND flash controller selected");
return ERROR_NAND_OPERATION_FAILED;
- }
- else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
- {
- uint8_t *page_buffer;
+ } else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER) {
uint8_t *oob_buffer;
int quarter, num_quarters;
- if (!data && oob)
- {
+ if (!data && oob) {
LOG_ERROR("LPC3180 MLC controller can't write OOB data only");
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
- if (oob && (oob_size > 6))
- {
- LOG_ERROR("LPC3180 MLC controller can't write more than 6 bytes of OOB data");
+ if (oob && (oob_size > 24)) {
+ LOG_ERROR("LPC3180 MLC controller can't write more "
+ "than 6 bytes for each quarter's OOB data");
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
- if (data_size > (uint32_t)nand->page_size)
- {
+ if (data_size > (uint32_t)nand->page_size) {
LOG_ERROR("data size exceeds page size");
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
page_buffer = malloc(512);
oob_buffer = malloc(6);
- if (nand->page_size == 512)
- {
+ if (nand->page_size == 512) {
/* MLC_ADDR = 0x0 (one column cycle) */
target_write_u32(target, 0x200b8004, 0x0);
if (nand->address_cycles == 4)
target_write_u32(target, 0x200b8004, (page >> 16) & 0xff);
- }
- else
- {
+ } else {
/* MLC_ADDR = 0x0 (two column cycles) */
target_write_u32(target, 0x200b8004, 0x0);
target_write_u32(target, 0x200b8004, 0x0);
*/
num_quarters = (nand->page_size == 2048) ? 4 : 1;
- for (quarter = 0; quarter < num_quarters; quarter++)
- {
+ for (quarter = 0; quarter < num_quarters; quarter++) {
int thisrun_data_size = (data_size > 512) ? 512 : data_size;
int thisrun_oob_size = (oob_size > 6) ? 6 : oob_size;
memset(page_buffer, 0xff, 512);
- if (data)
- {
+ if (data) {
memcpy(page_buffer, data, thisrun_data_size);
data_size -= thisrun_data_size;
data += thisrun_data_size;
}
- memset(oob_buffer, 0xff, (nand->page_size == 512) ? 6 : 24);
- if (oob)
- {
- memcpy(page_buffer, oob, thisrun_oob_size);
+ memset(oob_buffer, 0xff, 6);
+ if (oob) {
+ memcpy(oob_buffer, oob, thisrun_oob_size);
oob_size -= thisrun_oob_size;
oob += thisrun_oob_size;
}
/* write MLC_ECC_ENC_REG to start encode cycle */
target_write_u32(target, 0x200b8008, 0x0);
- target_write_memory(target, 0x200a8000, 4, 128, page_buffer + (quarter * 512));
- target_write_memory(target, 0x200a8000, 1, 6, oob_buffer + (quarter * 6));
+ target_write_memory(target, 0x200a8000,
+ 4, 128, page_buffer);
+ target_write_memory(target, 0x200a8000,
+ 1, 6, oob_buffer);
/* write MLC_ECC_AUTO_ENC_REG to start auto encode */
target_write_u32(target, 0x200b8010, 0x0);
- if (!lpc3180_controller_ready(nand, 1000))
- {
+ if (!lpc3180_controller_ready(nand, 1000)) {
LOG_ERROR("timeout while waiting for completion of auto encode cycle");
+ free(page_buffer);
+ free(oob_buffer);
return ERROR_NAND_OPERATION_FAILED;
}
}
/* MLC_CMD = auto program command */
target_write_u32(target, 0x200b8000, NAND_CMD_PAGEPROG);
- if ((retval = nand_read_status(nand, &status)) != ERROR_OK)
- {
+ retval = nand_read_status(nand, &status);
+ if (retval != ERROR_OK) {
LOG_ERROR("couldn't read status");
+ free(page_buffer);
+ free(oob_buffer);
return ERROR_NAND_OPERATION_FAILED;
}
- if (status & NAND_STATUS_FAIL)
- {
+ if (status & NAND_STATUS_FAIL) {
LOG_ERROR("write operation didn't pass, status: 0x%2.2x", status);
+ free(page_buffer);
+ free(oob_buffer);
return ERROR_NAND_OPERATION_FAILED;
}
free(page_buffer);
free(oob_buffer);
- }
- else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER)
- {
- return nand_write_page_raw(nand, page, data, data_size, oob, oob_size);
+ } else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
+
+ /**********************************************************************
+ * Write both SLC NAND flash page main area and spare area.
+ * Small page -
+ * ------------------------------------------
+ * | 512 bytes main | 16 bytes spare |
+ * ------------------------------------------
+ * Large page -
+ * ------------------------------------------
+ * | 2048 bytes main | 64 bytes spare |
+ * ------------------------------------------
+ * If DMA & ECC enabled, then the ECC generated for the 1st 256-byte
+ * data is written to the 3rd word of the spare area. The ECC
+ * generated for the 2nd 256-byte data is written to the 4th word
+ * of the spare area. The ECC generated for the 3rd 256-byte data is
+ * written to the 7th word of the spare area. The ECC generated
+ * for the 4th 256-byte data is written to the 8th word of the
+ * spare area and so on.
+ *
+ **********************************************************************/
+
+ int i = 0, target_mem_base;
+ uint8_t *ecc_flash_buffer;
+ struct working_area *pworking_area;
+
+ if (lpc3180_info->is_bulk) {
+
+ if (!data && oob) {
+ /*if oob only mode is active original method is used as SLC
+ *controller hangs during DMA interworking. Anyway the code supports
+ *the oob only mode below. */
+ return nand_write_page_raw(nand,
+ page,
+ data,
+ data_size,
+ oob,
+ oob_size);
+ }
+ retval = nand_page_command(nand, page, NAND_CMD_SEQIN, !data);
+ if (ERROR_OK != retval)
+ return retval;
+
+ /* allocate a working area */
+ if (target->working_area_size < (uint32_t) nand->page_size + 0x200) {
+ LOG_ERROR("Reserve at least 0x%x physical target working area",
+ nand->page_size + 0x200);
+ return ERROR_FLASH_OPERATION_FAILED;
+ }
+ if (target->working_area_phys%4) {
+ LOG_ERROR(
+ "Reserve the physical target working area at word boundary");
+ return ERROR_FLASH_OPERATION_FAILED;
+ }
+ if (target_alloc_working_area(target, target->working_area_size,
+ &pworking_area) != ERROR_OK) {
+ LOG_ERROR("no working area specified, can't read LPC internal flash");
+ return ERROR_FLASH_OPERATION_FAILED;
+ }
+ target_mem_base = target->working_area_phys;
+
+ if (nand->page_size == 2048)
+ page_buffer = malloc(2048);
+ else
+ page_buffer = malloc(512);
+
+ ecc_flash_buffer = malloc(64);
+
+ /* SLC_CFG = 0x (Force nCE assert, DMA ECC enabled, ECC enabled, DMA burst
+ *enabled, DMA write to SLC, WIDTH = bus_width) */
+ target_write_u32(target, 0x20020014, 0x3c);
+
+ if (data && !oob) {
+ /* set DMA LLI-s in target memory and in DMA*/
+ for (i = 0; i < nand->page_size/0x100; i++) {
+
+ int tmp;
+ /* -------LLI for 256 byte block---------
+ * DMACC0SrcAddr = SRAM */
+ target_write_u32(target,
+ target_mem_base+0+i*32,
+ target_mem_base+DATA_OFFS+i*256);
+ if (i == 0)
+ target_write_u32(target,
+ 0x31000100,
+ target_mem_base+DATA_OFFS);
+ /* DMACCxDestAddr = SLC_DMA_DATA */
+ target_write_u32(target, target_mem_base+4+i*32, 0x20020038);
+ if (i == 0)
+ target_write_u32(target, 0x31000104, 0x20020038);
+ /* DMACCxLLI = next element */
+ tmp = (target_mem_base+(1+i*2)*16)&0xfffffffc;
+ target_write_u32(target, target_mem_base+8+i*32, tmp);
+ if (i == 0)
+ target_write_u32(target, 0x31000108, tmp);
+ /* DMACCxControl = TransferSize =64, Source burst size =16,
+ * Destination burst size = 16, Source transfer width = 32 bit,
+ * Destination transfer width = 32 bit, Source AHB master select = M0,
+ * Destination AHB master select = M0, Source increment = 1,
+ * Destination increment = 0, Terminal count interrupt enable bit = 0*/
+ target_write_u32(target,
+ target_mem_base+12+i*32,
+ 0x40 | 3<<12 | 3<<15 | 2<<18 | 2<<21 | 0<<24 | 0<<25 | 1<<26 |
+ 0<<27 | 0<<31);
+ if (i == 0)
+ target_write_u32(target,
+ 0x3100010c,
+ 0x40 | 3<<12 | 3<<15 | 2<<18 | 2<<21 | 0<<24 | 0<<25 | 1<<26 |
+ 0<<27 | 0<<31);
+
+ /* -------LLI for 3 byte ECC---------
+ * DMACC0SrcAddr = SLC_ECC*/
+ target_write_u32(target, target_mem_base+16+i*32, 0x20020034);
+ /* DMACCxDestAddr = SRAM */
+ target_write_u32(target,
+ target_mem_base+20+i*32,
+ target_mem_base+SPARE_OFFS+8+16*(i>>1)+(i%2)*4);
+ /* DMACCxLLI = next element */
+ tmp = (target_mem_base+(2+i*2)*16)&0xfffffffc;
+ target_write_u32(target, target_mem_base+24+i*32, tmp);
+ /* DMACCxControl = TransferSize =1, Source burst size =4,
+ * Destination burst size = 4, Source transfer width = 32 bit,
+ * Destination transfer width = 32 bit, Source AHB master select = M0,
+ * Destination AHB master select = M0, Source increment = 0,
+ * Destination increment = 1, Terminal count interrupt enable bit = 0*/
+ target_write_u32(target,
+ target_mem_base+28+i*32,
+ 0x01 | 1<<12 | 1<<15 | 2<<18 | 2<<21 | 0<<24 | 0<<25 | 0<<26 | 1<<27 | 0<<
+ 31);
+ }
+ } else if (data && oob) {
+ /* -------LLI for 512 or 2048 bytes page---------
+ * DMACC0SrcAddr = SRAM */
+ target_write_u32(target, target_mem_base, target_mem_base+DATA_OFFS);
+ target_write_u32(target, 0x31000100, target_mem_base+DATA_OFFS);
+ /* DMACCxDestAddr = SLC_DMA_DATA */
+ target_write_u32(target, target_mem_base+4, 0x20020038);
+ target_write_u32(target, 0x31000104, 0x20020038);
+ /* DMACCxLLI = next element */
+ target_write_u32(target,
+ target_mem_base+8,
+ (target_mem_base+32)&0xfffffffc);
+ target_write_u32(target, 0x31000108,
+ (target_mem_base+32)&0xfffffffc);
+ /* DMACCxControl = TransferSize =512 or 128, Source burst size =16,
+ * Destination burst size = 16, Source transfer width = 32 bit,
+ * Destination transfer width = 32 bit, Source AHB master select = M0,
+ * Destination AHB master select = M0, Source increment = 1,
+ * Destination increment = 0, Terminal count interrupt enable bit = 0*/
+ target_write_u32(target,
+ target_mem_base+12,
+ (nand->page_size ==
+ 2048 ? 512 : 128) | 3<<12 | 3<<15 | 2<<18 | 2<<21 | 0<<24 | 0<<25 |
+ 1<<26 | 0<<27 | 0<<31);
+ target_write_u32(target,
+ 0x3100010c,
+ (nand->page_size ==
+ 2048 ? 512 : 128) | 3<<12 | 3<<15 | 2<<18 | 2<<21 | 0<<24 | 0<<25 |
+ 1<<26 | 0<<27 | 0<<31);
+ i = 1;
+ } else if (!data && oob)
+ i = 0;
+
+ /* -------LLI for spare area---------
+ * DMACC0SrcAddr = SRAM*/
+ target_write_u32(target, target_mem_base+0+i*32, target_mem_base+SPARE_OFFS);
+ if (i == 0)
+ target_write_u32(target, 0x31000100, target_mem_base+SPARE_OFFS);
+ /* DMACCxDestAddr = SLC_DMA_DATA */
+ target_write_u32(target, target_mem_base+4+i*32, 0x20020038);
+ if (i == 0)
+ target_write_u32(target, 0x31000104, 0x20020038);
+ /* DMACCxLLI = next element = NULL */
+ target_write_u32(target, target_mem_base+8+i*32, 0);
+ if (i == 0)
+ target_write_u32(target, 0x31000108, 0);
+ /* DMACCxControl = TransferSize =16 for large page or 4 for small page,
+ * Source burst size =16, Destination burst size = 16, Source transfer width = 32 bit,
+ * Destination transfer width = 32 bit, Source AHB master select = M0,
+ * Destination AHB master select = M0, Source increment = 1,
+ * Destination increment = 0, Terminal count interrupt enable bit = 0*/
+ target_write_u32(target,
+ target_mem_base+12+i*32,
+ (nand->page_size ==
+ 2048 ? 0x10 : 0x04) | 3<<12 | 3<<15 | 2<<18 | 2<<21 | 0<<24 | 0<<25 | 1<<26 |
+ 0<<27 | 0<<31);
+ if (i == 0)
+ target_write_u32(target, 0x3100010c,
+ (nand->page_size == 2048 ?
+ 0x10 : 0x04) | 3<<12 | 3<<15 | 2<<18 | 2<<21 | 0<<24 |
+ 0<<25 | 1<<26 | 0<<27 | 0<<31);
+
+ memset(ecc_flash_buffer, 0xff, 64);
+ if (oob)
+ memcpy(ecc_flash_buffer, oob, oob_size);
+ target_write_memory(target,
+ target_mem_base+SPARE_OFFS,
+ 4,
+ 16,
+ ecc_flash_buffer);
+
+ if (data) {
+ memset(page_buffer, 0xff, nand->page_size == 2048 ? 2048 : 512);
+ memcpy(page_buffer, data, data_size);
+ target_write_memory(target,
+ target_mem_base+DATA_OFFS,
+ 4,
+ nand->page_size == 2048 ? 512 : 128,
+ page_buffer);
+ }
+
+ free(page_buffer);
+ free(ecc_flash_buffer);
+
+ /* Enable DMA after channel set up !
+ LLI only works when DMA is the flow controller!
+ */
+ /* DMACCxConfig= E=1, SrcPeripheral = 1 (SLC), DestPeripheral = 1 (SLC),
+ *FlowCntrl = 2 (Pher -> Mem, DMA), IE = 0, ITC = 0, L= 0, H=0*/
+ target_write_u32(target,
+ 0x31000110,
+ 1 | 1<<1 | 1<<6 | 2<<11 | 0<<14 | 0<<15 | 0<<16 | 0<<18);
+
+ /* SLC_CTRL = 3 (START DMA), ECC_CLEAR */
+ target_write_u32(target, 0x20020010, 0x3);
+
+ /* SLC_ICR = 2, INT_TC_CLR, clear pending TC*/
+ target_write_u32(target, 0x20020028, 2);
+
+ /* SLC_TC */
+ if (!data && oob)
+ target_write_u32(target, 0x20020030,
+ (nand->page_size == 2048 ? 0x10 : 0x04));
+ else
+ target_write_u32(target, 0x20020030,
+ (nand->page_size == 2048 ? 0x840 : 0x210));
+
+ nand_write_finish(nand);
+
+ if (!lpc3180_tc_ready(nand, 1000)) {
+ LOG_ERROR("timeout while waiting for completion of DMA");
+ return ERROR_NAND_OPERATION_FAILED;
+ }
+
+ target_free_working_area(target, pworking_area);
+
+ LOG_INFO("Page = 0x%" PRIx32 " was written.", page);
+
+ } else
+ return nand_write_page_raw(nand, page, data, data_size, oob, oob_size);
}
return ERROR_OK;
}
-static int lpc3180_read_page(struct nand_device *nand, uint32_t page, uint8_t *data, uint32_t data_size, uint8_t *oob, uint32_t oob_size)
+static int lpc3180_read_page(struct nand_device *nand,
+ uint32_t page,
+ uint8_t *data,
+ uint32_t data_size,
+ uint8_t *oob,
+ uint32_t oob_size)
{
struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
- struct target *target = lpc3180_info->target;
+ struct target *target = nand->target;
+ uint8_t *page_buffer;
- if (target->state != TARGET_HALTED)
- {
+ if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
- if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER)
- {
+ if (lpc3180_info->selected_controller == LPC3180_NO_CONTROLLER) {
LOG_ERROR("BUG: no LPC3180 NAND flash controller selected");
return ERROR_NAND_OPERATION_FAILED;
- }
- else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
- {
- uint8_t *page_buffer;
+ } else if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER) {
uint8_t *oob_buffer;
uint32_t page_bytes_done = 0;
uint32_t oob_bytes_done = 0;
uint32_t mlc_isr;
#if 0
- if (oob && (oob_size > 6))
- {
+ if (oob && (oob_size > 6)) {
LOG_ERROR("LPC3180 MLC controller can't read more than 6 bytes of OOB data");
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
#endif
- if (data_size > (uint32_t)nand->page_size)
- {
+ if (data_size > (uint32_t)nand->page_size) {
LOG_ERROR("data size exceeds page size");
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
- if (nand->page_size == 2048)
- {
+ if (nand->page_size == 2048) {
page_buffer = malloc(2048);
oob_buffer = malloc(64);
- }
- else
- {
+ } else {
page_buffer = malloc(512);
oob_buffer = malloc(16);
}
- if (!data && oob)
- {
+ if (!data && oob) {
/* MLC_CMD = Read OOB
* we can use the READOOB command on both small and large page devices,
* as the controller translates the 0x50 command to a 0x0 with appropriate
* positioning of the serial buffer read pointer
*/
target_write_u32(target, 0x200b8000, NAND_CMD_READOOB);
- }
- else
- {
+ } else {
/* MLC_CMD = Read0 */
target_write_u32(target, 0x200b8000, NAND_CMD_READ0);
}
- if (nand->page_size == 512)
- {
- /* small page device */
- /* MLC_ADDR = 0x0 (one column cycle) */
+ if (nand->page_size == 512) {
+ /* small page device
+ * MLC_ADDR = 0x0 (one column cycle) */
target_write_u32(target, 0x200b8004, 0x0);
/* MLC_ADDR = row */
if (nand->address_cycles == 4)
target_write_u32(target, 0x200b8004, (page >> 16) & 0xff);
- }
- else
- {
- /* large page device */
- /* MLC_ADDR = 0x0 (two column cycles) */
+ } else {
+ /* large page device
+ * MLC_ADDR = 0x0 (two column cycles) */
target_write_u32(target, 0x200b8004, 0x0);
target_write_u32(target, 0x200b8004, 0x0);
target_write_u32(target, 0x200b8000, NAND_CMD_READSTART);
}
- while (page_bytes_done < (uint32_t)nand->page_size)
- {
+ while (page_bytes_done < (uint32_t)nand->page_size) {
/* MLC_ECC_AUTO_DEC_REG = dummy */
target_write_u32(target, 0x200b8014, 0xaa55aa55);
- if (!lpc3180_controller_ready(nand, 1000))
- {
+ if (!lpc3180_controller_ready(nand, 1000)) {
LOG_ERROR("timeout while waiting for completion of auto decode cycle");
+ free(page_buffer);
+ free(oob_buffer);
return ERROR_NAND_OPERATION_FAILED;
}
target_read_u32(target, 0x200b8048, &mlc_isr);
- if (mlc_isr & 0x8)
- {
- if (mlc_isr & 0x40)
- {
- LOG_ERROR("uncorrectable error detected: 0x%2.2x", (unsigned)mlc_isr);
+ if (mlc_isr & 0x8) {
+ if (mlc_isr & 0x40) {
+ LOG_ERROR("uncorrectable error detected: 0x%2.2x",
+ (unsigned)mlc_isr);
+ free(page_buffer);
+ free(oob_buffer);
return ERROR_NAND_OPERATION_FAILED;
}
- LOG_WARNING("%i symbol error detected and corrected", ((int)(((mlc_isr & 0x30) >> 4) + 1)));
+ LOG_WARNING("%i symbol error detected and corrected",
+ ((int)(((mlc_isr & 0x30) >> 4) + 1)));
}
if (data)
- {
- target_read_memory(target, 0x200a8000, 4, 128, page_buffer + page_bytes_done);
- }
+ target_read_memory(target,
+ 0x200a8000,
+ 4,
+ 128,
+ page_buffer + page_bytes_done);
if (oob)
- {
- target_read_memory(target, 0x200a8000, 4, 4, oob_buffer + oob_bytes_done);
- }
+ target_read_memory(target,
+ 0x200a8000,
+ 4,
+ 4,
+ oob_buffer + oob_bytes_done);
page_bytes_done += 512;
oob_bytes_done += 16;
free(page_buffer);
free(oob_buffer);
- }
- else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER)
- {
- return nand_read_page_raw(nand, page, data, data_size, oob, oob_size);
+ } else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
+
+ /**********************************************************************
+ * Read both SLC NAND flash page main area and spare area.
+ * Small page -
+ * ------------------------------------------
+ * | 512 bytes main | 16 bytes spare |
+ * ------------------------------------------
+ * Large page -
+ * ------------------------------------------
+ * | 2048 bytes main | 64 bytes spare |
+ * ------------------------------------------
+ * If DMA & ECC enabled, then the ECC generated for the 1st 256-byte
+ * data is compared with the 3rd word of the spare area. The ECC
+ * generated for the 2nd 256-byte data is compared with the 4th word
+ * of the spare area. The ECC generated for the 3rd 256-byte data is
+ * compared with the 7th word of the spare area. The ECC generated
+ * for the 4th 256-byte data is compared with the 8th word of the
+ * spare area and so on.
+ *
+ **********************************************************************/
+
+ int retval, i, target_mem_base;
+ uint8_t *ecc_hw_buffer;
+ uint8_t *ecc_flash_buffer;
+ struct working_area *pworking_area;
+
+ if (lpc3180_info->is_bulk) {
+
+ /* read always the data and also oob areas*/
+
+ retval = nand_page_command(nand, page, NAND_CMD_READ0, 0);
+ if (ERROR_OK != retval)
+ return retval;
+
+ /* allocate a working area */
+ if (target->working_area_size < (uint32_t) nand->page_size + 0x200) {
+ LOG_ERROR("Reserve at least 0x%x physical target working area",
+ nand->page_size + 0x200);
+ return ERROR_FLASH_OPERATION_FAILED;
+ }
+ if (target->working_area_phys%4) {
+ LOG_ERROR(
+ "Reserve the physical target working area at word boundary");
+ return ERROR_FLASH_OPERATION_FAILED;
+ }
+ if (target_alloc_working_area(target, target->working_area_size,
+ &pworking_area) != ERROR_OK) {
+ LOG_ERROR("no working area specified, can't read LPC internal flash");
+ return ERROR_FLASH_OPERATION_FAILED;
+ }
+ target_mem_base = target->working_area_phys;
+
+ if (nand->page_size == 2048)
+ page_buffer = malloc(2048);
+ else
+ page_buffer = malloc(512);
+
+ ecc_hw_buffer = malloc(32);
+ ecc_flash_buffer = malloc(64);
+
+ /* SLC_CFG = 0x (Force nCE assert, DMA ECC enabled, ECC enabled, DMA burst
+ *enabled, DMA read from SLC, WIDTH = bus_width) */
+ target_write_u32(target, 0x20020014, 0x3e);
+
+ /* set DMA LLI-s in target memory and in DMA*/
+ for (i = 0; i < nand->page_size/0x100; i++) {
+ int tmp;
+ /* -------LLI for 256 byte block---------
+ * DMACC0SrcAddr = SLC_DMA_DATA*/
+ target_write_u32(target, target_mem_base+0+i*32, 0x20020038);
+ if (i == 0)
+ target_write_u32(target, 0x31000100, 0x20020038);
+ /* DMACCxDestAddr = SRAM */
+ target_write_u32(target,
+ target_mem_base+4+i*32,
+ target_mem_base+DATA_OFFS+i*256);
+ if (i == 0)
+ target_write_u32(target,
+ 0x31000104,
+ target_mem_base+DATA_OFFS);
+ /* DMACCxLLI = next element */
+ tmp = (target_mem_base+(1+i*2)*16)&0xfffffffc;
+ target_write_u32(target, target_mem_base+8+i*32, tmp);
+ if (i == 0)
+ target_write_u32(target, 0x31000108, tmp);
+ /* DMACCxControl = TransferSize =64, Source burst size =16,
+ * Destination burst size = 16, Source transfer width = 32 bit,
+ * Destination transfer width = 32 bit, Source AHB master select = M0,
+ * Destination AHB master select = M0, Source increment = 0,
+ * Destination increment = 1, Terminal count interrupt enable bit = 0*/
+ target_write_u32(target,
+ target_mem_base+12+i*32,
+ 0x40 | 3<<12 | 3<<15 | 2<<18 | 2<<21 | 0<<24 | 0<<25 | 0<<26 | 1<<27 | 0<<
+ 31);
+ if (i == 0)
+ target_write_u32(target,
+ 0x3100010c,
+ 0x40 | 3<<12 | 3<<15 | 2<<18 | 2<<21 | 0<<24 | 0<<25 | 0<<26 | 1<<27 | 0<<
+ 31);
+
+ /* -------LLI for 3 byte ECC---------
+ * DMACC0SrcAddr = SLC_ECC*/
+ target_write_u32(target, target_mem_base+16+i*32, 0x20020034);
+ /* DMACCxDestAddr = SRAM */
+ target_write_u32(target,
+ target_mem_base+20+i*32,
+ target_mem_base+ECC_OFFS+i*4);
+ /* DMACCxLLI = next element */
+ tmp = (target_mem_base+(2+i*2)*16)&0xfffffffc;
+ target_write_u32(target, target_mem_base+24+i*32, tmp);
+ /* DMACCxControl = TransferSize =1, Source burst size =4,
+ * Destination burst size = 4, Source transfer width = 32 bit,
+ * Destination transfer width = 32 bit, Source AHB master select = M0,
+ * Destination AHB master select = M0, Source increment = 0,
+ * Destination increment = 1, Terminal count interrupt enable bit = 0*/
+ target_write_u32(target,
+ target_mem_base+28+i*32,
+ 0x01 | 1<<12 | 1<<15 | 2<<18 | 2<<21 | 0<<24 | 0<<25 | 0<<26 | 1<<27 | 0<<
+ 31);
+ }
+
+ /* -------LLI for spare area---------
+ * DMACC0SrcAddr = SLC_DMA_DATA*/
+ target_write_u32(target, target_mem_base+0+i*32, 0x20020038);
+ /* DMACCxDestAddr = SRAM */
+ target_write_u32(target, target_mem_base+4+i*32, target_mem_base+SPARE_OFFS);
+ /* DMACCxLLI = next element = NULL */
+ target_write_u32(target, target_mem_base+8+i*32, 0);
+ /* DMACCxControl = TransferSize =16 for large page or 4 for small page,
+ * Source burst size =16, Destination burst size = 16, Source transfer width = 32 bit,
+ * Destination transfer width = 32 bit, Source AHB master select = M0,
+ * Destination AHB master select = M0, Source increment = 0,
+ * Destination increment = 1, Terminal count interrupt enable bit = 0*/
+ target_write_u32(target,
+ target_mem_base + 12 + i * 32,
+ (nand->page_size == 2048 ? 0x10 : 0x04) | 3<<12 | 3<<15 | 2<<18 | 2<<21 |
+ 0<<24 | 0<<25 | 0<<26 | 1<<27 | 0<<31);
+
+ /* Enable DMA after channel set up !
+ LLI only works when DMA is the flow controller!
+ */
+ /* DMACCxConfig= E=1, SrcPeripheral = 1 (SLC), DestPeripheral = 1 (SLC),
+ *FlowCntrl = 2 (Pher-> Mem, DMA), IE = 0, ITC = 0, L= 0, H=0*/
+ target_write_u32(target,
+ 0x31000110,
+ 1 | 1<<1 | 1<<6 | 2<<11 | 0<<14 | 0<<15 | 0<<16 | 0<<18);
+
+ /* SLC_CTRL = 3 (START DMA), ECC_CLEAR */
+ target_write_u32(target, 0x20020010, 0x3);
+
+ /* SLC_ICR = 2, INT_TC_CLR, clear pending TC*/
+ target_write_u32(target, 0x20020028, 2);
+
+ /* SLC_TC */
+ target_write_u32(target, 0x20020030,
+ (nand->page_size == 2048 ? 0x840 : 0x210));
+
+ if (!lpc3180_tc_ready(nand, 1000)) {
+ LOG_ERROR("timeout while waiting for completion of DMA");
+ free(page_buffer);
+ free(ecc_hw_buffer);
+ free(ecc_flash_buffer);
+ target_free_working_area(target, pworking_area);
+ return ERROR_NAND_OPERATION_FAILED;
+ }
+
+ if (data) {
+ target_read_memory(target,
+ target_mem_base+DATA_OFFS,
+ 4,
+ nand->page_size == 2048 ? 512 : 128,
+ page_buffer);
+ memcpy(data, page_buffer, data_size);
+
+ LOG_INFO("Page = 0x%" PRIx32 " was read.", page);
+
+ /* check hw generated ECC for each 256 bytes block with the saved
+ *ECC in flash spare area*/
+ int idx = nand->page_size/0x200;
+ target_read_memory(target,
+ target_mem_base+SPARE_OFFS,
+ 4,
+ 16,
+ ecc_flash_buffer);
+ target_read_memory(target,
+ target_mem_base+ECC_OFFS,
+ 4,
+ 8,
+ ecc_hw_buffer);
+ for (i = 0; i < idx; i++) {
+ if ((0x00ffffff & *(uint32_t *)(void *)(ecc_hw_buffer+i*8)) !=
+ (0x00ffffff & *(uint32_t *)(void *)(ecc_flash_buffer+8+i*16)))
+ LOG_WARNING(
+ "ECC mismatch at 256 bytes size block= %d at page= 0x%" PRIx32,
+ i * 2 + 1, page);
+ if ((0x00ffffff & *(uint32_t *)(void *)(ecc_hw_buffer+4+i*8)) !=
+ (0x00ffffff & *(uint32_t *)(void *)(ecc_flash_buffer+12+i*16)))
+ LOG_WARNING(
+ "ECC mismatch at 256 bytes size block= %d at page= 0x%" PRIx32,
+ i * 2 + 2, page);
+ }
+ }
+
+ if (oob)
+ memcpy(oob, ecc_flash_buffer, oob_size);
+
+ free(page_buffer);
+ free(ecc_hw_buffer);
+ free(ecc_flash_buffer);
+
+ target_free_working_area(target, pworking_area);
+
+ } else
+ return nand_read_page_raw(nand, page, data, data_size, oob, oob_size);
}
return ERROR_OK;
static int lpc3180_controller_ready(struct nand_device *nand, int timeout)
{
struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
- struct target *target = lpc3180_info->target;
- uint8_t status = 0x0;
+ struct target *target = nand->target;
- if (target->state != TARGET_HALTED)
- {
+ if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
- do
- {
- if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
- {
+ LOG_DEBUG("lpc3180_controller_ready count start=%d", timeout);
+
+ do {
+ if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER) {
+ uint8_t status;
+
/* Read MLC_ISR, wait for controller to become ready */
target_read_u8(target, 0x200b8048, &status);
- if (status & 2)
+ if (status & 2) {
+ LOG_DEBUG("lpc3180_controller_ready count=%d",
+ timeout);
return 1;
- }
- else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER)
- {
- /* we pretend that the SLC controller is always ready */
- return 1;
+ }
+ } else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
+ uint32_t status;
+
+ /* Read SLC_STAT and check READY bit */
+ target_read_u32(target, 0x20020018, &status);
+
+ if (status & 1) {
+ LOG_DEBUG("lpc3180_controller_ready count=%d",
+ timeout);
+ return 1;
+ }
}
alive_sleep(1);
static int lpc3180_nand_ready(struct nand_device *nand, int timeout)
{
struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
- struct target *target = lpc3180_info->target;
+ struct target *target = nand->target;
- if (target->state != TARGET_HALTED)
- {
+ if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
- do
- {
- if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
- {
+ LOG_DEBUG("lpc3180_nand_ready count start=%d", timeout);
+
+ do {
+ if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER) {
uint8_t status = 0x0;
/* Read MLC_ISR, wait for NAND flash device to become ready */
target_read_u8(target, 0x200b8048, &status);
- if (status & 1)
+ if (status & 1) {
+ LOG_DEBUG("lpc3180_nand_ready count end=%d",
+ timeout);
return 1;
- }
- else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER)
- {
+ }
+ } else if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
uint32_t status = 0x0;
/* Read SLC_STAT and check READY bit */
target_read_u32(target, 0x20020018, &status);
- if (status & 1)
+ if (status & 1) {
+ LOG_DEBUG("lpc3180_nand_ready count end=%d",
+ timeout);
+ return 1;
+ }
+ }
+
+ alive_sleep(1);
+ } while (timeout-- > 0);
+
+ return 0;
+}
+
+static int lpc3180_tc_ready(struct nand_device *nand, int timeout)
+{
+ struct lpc3180_nand_controller *lpc3180_info = nand->controller_priv;
+ struct target *target = nand->target;
+
+ if (target->state != TARGET_HALTED) {
+ LOG_ERROR("target must be halted to use LPC3180 NAND flash controller");
+ return ERROR_NAND_OPERATION_FAILED;
+ }
+
+ LOG_DEBUG("lpc3180_tc_ready count start=%d",
+ timeout);
+
+ do {
+ if (lpc3180_info->selected_controller == LPC3180_SLC_CONTROLLER) {
+ uint32_t status = 0x0;
+ /* Read SLC_INT_STAT and check INT_TC_STAT bit */
+ target_read_u32(target, 0x2002001c, &status);
+
+ if (status & 2) {
+ LOG_DEBUG("lpc3180_tc_ready count=%d",
+ timeout);
return 1;
+ }
}
alive_sleep(1);
COMMAND_HANDLER(handle_lpc3180_select_command)
{
struct lpc3180_nand_controller *lpc3180_info = NULL;
- char *selected[] =
- {
+ char *selected[] = {
"no", "mlc", "slc"
};
- if ((CMD_ARGC < 1) || (CMD_ARGC > 2))
- {
+ if ((CMD_ARGC < 1) || (CMD_ARGC > 3))
return ERROR_COMMAND_SYNTAX_ERROR;
- }
unsigned num;
- COMMAND_PARSE_NUMBER(uint, CMD_ARGV[1], num);
+ COMMAND_PARSE_NUMBER(uint, CMD_ARGV[0], num);
struct nand_device *nand = get_nand_device_by_num(num);
- if (!nand)
- {
+ if (!nand) {
command_print(CMD_CTX, "nand device '#%s' is out of bounds", CMD_ARGV[0]);
return ERROR_OK;
}
lpc3180_info = nand->controller_priv;
- if (CMD_ARGC == 2)
- {
+ if (CMD_ARGC >= 2) {
if (strcmp(CMD_ARGV[1], "mlc") == 0)
- {
lpc3180_info->selected_controller = LPC3180_MLC_CONTROLLER;
- }
- else if (strcmp(CMD_ARGV[1], "slc") == 0)
- {
+ else if (strcmp(CMD_ARGV[1], "slc") == 0) {
lpc3180_info->selected_controller = LPC3180_SLC_CONTROLLER;
- }
- else
- {
+ if (CMD_ARGC == 3 && strcmp(CMD_ARGV[2], "bulk") == 0)
+ lpc3180_info->is_bulk = 1;
+ else
+ lpc3180_info->is_bulk = 0;
+ } else
return ERROR_COMMAND_SYNTAX_ERROR;
- }
}
- command_print(CMD_CTX, "%s controller selected", selected[lpc3180_info->selected_controller]);
+ if (lpc3180_info->selected_controller == LPC3180_MLC_CONTROLLER)
+ command_print(CMD_CTX, "%s controller selected",
+ selected[lpc3180_info->selected_controller]);
+ else
+ command_print(CMD_CTX,
+ lpc3180_info->is_bulk ? "%s controller selected bulk mode is available" :
+ "%s controller selected bulk mode is not available",
+ selected[lpc3180_info->selected_controller]);
return ERROR_OK;
}
static const struct command_registration lpc3180_exec_command_handlers[] = {
{
.name = "select",
- .handler = &handle_lpc3180_select_command,
+ .handler = handle_lpc3180_select_command,
.mode = COMMAND_EXEC,
- .help = "select <'mlc'|'slc'> controller (default is mlc)",
- .usage = "<device_id> (mlc|slc)",
+ .help =
+ "select MLC or SLC controller (default is MLC), SLC can be set to bulk mode",
+ .usage = "bank_id ['mlc'|'slc' ['bulk'] ]",
},
COMMAND_REGISTRATION_DONE
};
.name = "lpc3180",
.mode = COMMAND_ANY,
.help = "LPC3180 NAND flash controller commands",
+ .usage = "",
.chain = lpc3180_exec_command_handlers,
},
COMMAND_REGISTRATION_DONE
};
struct nand_flash_controller lpc3180_nand_controller = {
- .name = "lpc3180",
- .commands = lpc3180_command_handler,
- .nand_device_command = lpc3180_nand_device_command,
- .init = lpc3180_init,
- .reset = lpc3180_reset,
- .command = lpc3180_command,
- .address = lpc3180_address,
- .write_data = lpc3180_write_data,
- .read_data = lpc3180_read_data,
- .write_page = lpc3180_write_page,
- .read_page = lpc3180_read_page,
- .controller_ready = lpc3180_controller_ready,
- .nand_ready = lpc3180_nand_ready,
- };
+ .name = "lpc3180",
+ .commands = lpc3180_command_handler,
+ .nand_device_command = lpc3180_nand_device_command,
+ .init = lpc3180_init,
+ .reset = lpc3180_reset,
+ .command = lpc3180_command,
+ .address = lpc3180_address,
+ .write_data = lpc3180_write_data,
+ .read_data = lpc3180_read_data,
+ .write_page = lpc3180_write_page,
+ .read_page = lpc3180_read_page,
+ .nand_ready = lpc3180_nand_ready,
+};
Code Review / openocd.git / blobdiff