(int (*)(const char *, int))open,
close,
(int (*)(int, const void *, int))write,
- ( int (*)(int, void *, int))read
+ (int (*)(int, void *, int))read
};
#endif
}
#endif
-extern int eth0_up;
static FILE *log;
static char reboot_stack[2048];
void copydir(char *name, char *destdir);
#if 0
-MTAB_ENTRY( romfs_mte1,
+MTAB_ENTRY(romfs_mte1,
"/rom",
"romfs",
"",
- (CYG_ADDRWORD) &filedata[0] );
+ (CYG_ADDRWORD) &filedata[0]);
#endif
void openocd_sleep_prelude(void)
}
cyg_io_flash_getconfig_erase_t e;
- void *err_addr;
len = sizeof(e);
e.offset = 0;
e.len = ds.dev_size;
- e.err_address = &err_addr;
diag_printf("Formatting 0x%08x bytes\n", (int)ds.dev_size);
err = cyg_io_get_config(handle, CYG_IO_GET_CONFIG_FLASH_ERASE, &e, &len);
if (err != ENOERR)
{
- diag_printf("Flash erase error %d offset 0x%p\n", err, err_addr);
+ diag_printf("Flash erase error %d offset 0x%08x\n", err, e.err_address);
reboot();
}
#ifdef CYGPKG_PROFILE_GPROF
start_profile();
#endif
- int actual = 0;
- int actual2 = 0;
- int pos, pos2;
+ size_t actual = 0;
+ size_t actual2 = 0;
+ size_t pos, pos2;
pos = 0;
pos2 = 0;
cur = 0;
if (actual2 <= 0)
{
memset(backwardBuffer, 's', sizeof(backwardBuffer));
- actual2 = read(serHandle, backwardBuffer,
+ int t;
+ t = read(serHandle, backwardBuffer,
sizeof(backwardBuffer));
- if (actual2 < 0)
+ actual2 = t;
+ if (t < 0)
{
if (errno != EAGAIN)
{
pos2 = 0;
}
- int x = actual2;
- int y = 0;
+ size_t x = actual2;
+ size_t y = 0;
if (actual2 > 0)
{
int written = write(session, backwardBuffer + pos2, actual2);
}
mkdir(zylin_config_dir, 0777);
- char *dirname=alloc_printf("%s/target", zylin_config_dir);
+ char *dirname = alloc_printf("%s/target", zylin_config_dir);
mkdir(dirname, 0777);
free(dirname);
- dirname=alloc_printf("%s/board", zylin_config_dir);
+ dirname = alloc_printf("%s/board", zylin_config_dir);
mkdir(dirname, 0777);
free(dirname);
- dirname=alloc_printf("%s/event", zylin_config_dir);
+ dirname = alloc_printf("%s/event", zylin_config_dir);
mkdir(dirname, 0777);
free(dirname);
if (logAllToSerial)
{
diag_printf(
- "%s/logserial=1 => sending log output to serial port using \"debug_level 3\" as default.\n", zylin_config_dir);
+ "%s/logserial = 1 => sending log output to serial port using \"debug_level 3\" as default.\n", zylin_config_dir);
command_run_line(cmd_ctx, "debug_level 3");
}
// For simplicity we use _FILESYSTEM synchronization for all accesses since
// we should never block in any filesystem operations.
#if 1
-FSTAB_ENTRY( tftpfs_fste, "tftpfs", 0,
+FSTAB_ENTRY(tftpfs_fste, "tftpfs", 0,
CYG_SYNCMODE_NONE,
tftpfs_mount,
tftpfs_umount,
// mtab entry.
// This defines a single ROMFS loaded into ROM at the configured address
//
-// MTAB_ENTRY( rom_mte, // structure name
+// MTAB_ENTRY(rom_mte, // structure name
// "/rom", // mount point
// "romfs", // FIlesystem type
// "", // hardware device
// (CYG_ADDRWORD) CYGNUM_FS_ROM_BASE_ADDRESS // Address in ROM
-// );
+//);
// -------------------------------------------------------------------------
// This defines the entry in the filesystem table.
// For simplicity we use _FILESYSTEM synchronization for all accesses since
// we should never block in any filesystem operations.
-FSTAB_ENTRY( logfs_fste, "logfs", 0,
- CYG_SYNCMODE_FILE_FILESYSTEM|CYG_SYNCMODE_IO_FILESYSTEM,
+FSTAB_ENTRY(logfs_fste, "logfs", 0,
+ CYG_SYNCMODE_FILE_FILESYSTEM | CYG_SYNCMODE_IO_FILESYSTEM,
logfs_mount,
logfs_umount,
logfs_open,