When using "pipe", also use log_output to redirect the log
output to a file so as not to flood the stdin/out pipes.
-The -p/--pipe option is deprecated and a warning is printed
-as it is equivalent to passing in -c "gdb_port pipe; log_output openocd.log".
-
Any other string is interpreted as named pipe to listen to.
Output pipe is the same name as input pipe, but with 'o' appended,
e.g. /var/gdb, /var/gdbo.
@end quotation
@end deffn
-@section I/O Utilities
-
-These commands are available when
-OpenOCD is built with @option{--enable-ioutil}.
-They are mainly useful on embedded targets,
-notably the ZY1000.
-Hosts with operating systems have complementary tools.
-
-@emph{Note:} there are several more such commands.
-
-@deffn Command append_file filename [string]*
-Appends the @var{string} parameters to
-the text file @file{filename}.
-Each string except the last one is followed by one space.
-The last string is followed by a newline.
-@end deffn
-
-@deffn Command cat filename
-Reads and displays the text file @file{filename}.
-@end deffn
-
-@deffn Command cp src_filename dest_filename
-Copies contents from the file @file{src_filename}
-into @file{dest_filename}.
-@end deffn
-
-@deffn Command ip
-@emph{No description provided.}
-@end deffn
-
-@deffn Command ls
-@emph{No description provided.}
-@end deffn
-
-@deffn Command mac
-@emph{No description provided.}
-@end deffn
-
-@deffn Command meminfo
-Display available RAM memory on OpenOCD host.
-Used in OpenOCD regression testing scripts.
-@end deffn
-
-@deffn Command peek
-@emph{No description provided.}
-@end deffn
-
-@deffn Command poke
-@emph{No description provided.}
-@end deffn
-
-@deffn Command rm filename
-@c "rm" has both normal and Jim-level versions??
-Unlinks the file @file{filename}.
-@end deffn
-
-@deffn Command trunc filename
-Removes all data in the file @file{filename}.
-@end deffn
-
@anchor{memoryaccess}
@section Memory access commands
@cindex memory access
@end deffn
-@deffn {Trace Port Driver} oocd_trace
-This driver isn't available unless OpenOCD was explicitly configured
-with the @option{--enable-oocd_trace} option. You probably don't want
-to configure it unless you've built the appropriate prototype hardware;
-it's @emph{proof-of-concept} software.
-
-Use the @option{oocd_trace} driver if you are configuring an ETM that's
-connected to an off-chip trace connector.
-
-@deffn {Config Command} {oocd_trace config} target tty
-Associates the ETM for @var{target} with a trace driver which
-collects data through the serial port @var{tty}.
-@end deffn
-
-@deffn Command {oocd_trace resync}
-Re-synchronizes with the capture clock.
-@end deffn
-
-@deffn Command {oocd_trace status}
-Reports whether the capture clock is locked or not.
-@end deffn
-@end deffn
-
@anchor{armcrosstrigger}
@section ARM Cross-Trigger Interface
@cindex CTI
speeds, like the 32kHz startup clock of an AT91RM9200.
@end deffn
-@subsection ARM720T specific commands
-@cindex ARM720T
-
-These commands are available to ARM720T based CPUs,
-which are implementations of the ARMv4T architecture
-based on the ARM7TDMI-S integer core.
-They are available in addition to the ARM and ARM7/ARM9 commands.
-
-@deffn Command {arm720t cp15} opcode [value]
-@emph{DEPRECATED -- avoid using this.
-Use the @command{arm mrc} or @command{arm mcr} commands instead.}
-
-Display cp15 register returned by the ARM instruction @var{opcode};
-else if a @var{value} is provided, that value is written to that register.
-The @var{opcode} should be the value of either an MRC or MCR instruction.
-@end deffn
-
@subsection ARM9 specific commands
@cindex ARM9
(Not all registers can be written.)
@end deffn
-@deffn Command {arm920t cp15i} opcode [value [address]]
-@emph{DEPRECATED -- avoid using this.
-Use the @command{arm mrc} or @command{arm mcr} commands instead.}
-
-Interpreted access using ARM instruction @var{opcode}, which should
-be the value of either an MRC or MCR instruction
-(as shown tables 9-11, 9-12, and 9-13 in the ARM920T TRM).
-If no @var{value} is provided, the result is displayed.
-Else if that value is written using the specified @var{address},
-or using zero if no other address is provided.
-@end deffn
-
@deffn Command {arm920t read_cache} filename
Dump the content of ICache and DCache to a file named @file{filename}.
@end deffn
@end deffn
-TODO: remove the old tpiu commands
-
-@deffn Command {tpiu config} (@option{disable} | ((@option{external} | @option{internal (@var{filename} | @var{:port} | -)}) @
- (@option{sync @var{port_width}} | ((@option{manchester} | @option{uart}) @var{formatter_enable})) @
- @var{TRACECLKIN_freq} [@var{trace_freq}]))
-
-ARMv7-M architecture provides several modules to generate debugging
-information internally (ITM, DWT and ETM). Their output is directed
-through TPIU to be captured externally either on an SWO pin (this
-configuration is called SWV) or on a synchronous parallel trace port.
-
-This command configures the TPIU module of the target and, if internal
-capture mode is selected, starts to capture trace output by using the
-debugger adapter features.
-
-Some targets require additional actions to be performed in the
-@b{trace-config} handler for trace port to be activated.
-
-Command options:
-@itemize @minus
-@item @option{disable} disable TPIU handling;
-@item @option{external} configure TPIU to let user capture trace
-output externally (with an additional UART or logic analyzer hardware).
-@item @option{internal (@var{filename} | @var{:port} | -)} configure TPIU and debug adapter to
-gather trace data then:
-
-@itemize @minus
-@item append it to a regular file or a named pipe if @var{filename} is specified.
-@item listen to a TCP/IP port if @var{:port} is specified, then broadcast the trace data over this port.
-@item if '-' is specified, OpenOCD will forward trace data to @command{tcl_trace} command.
-@*@b{Note:} while broadcasting to file or TCP, the forwarding to @command{tcl_trace} will remain active.
-@end itemize
-
-@item @option{sync @var{port_width}} use synchronous parallel trace output
-mode, and set port width to @var{port_width}.
-@item @option{manchester} use asynchronous SWO mode with Manchester
-coding.
-@item @option{uart} use asynchronous SWO mode with NRZ (same as
-regular UART 8N1) coding.
-@item @var{formatter_enable} is @option{on} or @option{off} to enable
-or disable TPIU formatter which needs to be used when both ITM and ETM
-data is to be output via SWO.
-@item @var{TRACECLKIN_freq} this should be specified to match target's
-current TRACECLKIN frequency (usually the same as HCLK).
-@item @var{trace_freq} trace port frequency. Can be omitted in
-internal mode to let the adapter driver select the maximum supported
-rate automatically.
-@end itemize
Example usage:
@enumerate
-c "stm32l1.tpiu enable"
@end example
@end enumerate
-@end deffn
@subsection ARMv7-M specific commands
@cindex tracing
Code Review / openocd.git / blobdiff