Returns the name of the debug adapter driver being used.
@end deffn
+@anchor{adapter_usb_location}
@deffn Command {adapter usb location} <bus>-<port>[.<port>]...
Specifies the physical USB port of the adapter to use. The path
roots at @var{bus} and walks down the physical ports, with each
and are not restricted to containing only decimal digits.)
@end deffn
-@deffn {Config Command} {ftdi_location} <bus>:<port>[,<port>]...
+@deffn {Config Command} {ftdi_location} <bus>-<port>[.<port>]...
+@emph{DEPRECATED -- avoid using this.
+Use the @xref{adapter_usb_location, adapter usb location} command instead.}
+
Specifies the physical USB port of the adapter to use. The path
roots at @var{bus} and walks down the physical ports, with each
@var{port} option specifying a deeper level in the bus topology, the last
flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
@end example
+If you use OTP (One-Time Programmable) memory define it as a second bank
+as per the following example.
+@example
+flash bank $_FLASHNAME stm32f2x 0x1FFF7800 0 0 0 $_TARGETNAME
+@end example
+
+@deffn Command {stm32f2x otp } num (@option{enable}|@option{disable}|@option{show})
+Enables or disables OTP write commands for bank @var{num}.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
Note that some devices have been found that have a flash size register that contains
an invalid value, to workaround this issue you can override the probed value used by
the flash driver.
@option{size} options using DMA.
@end deffn
+@deffn Command {$target_name catch_exc} [@option{off}|@option{sec_el1}|@option{sec_el3}|@option{nsec_el1}|@option{nsec_el2}]+
+Cause @command{$target_name} to halt when an exception is taken. Any combination of
+Secure (sec) EL1/EL3 or Non-Secure (nsec) EL1/EL2 is valid. The target
+@command{$target_name} will halt before taking the exception. In order to resume
+the target, the exception catch must be disabled again with @command{$target_name catch_exc off}.
+Issuing the command without options prints the current configuration.
+@end deffn
+
@section Intel Architecture
Intel Quark X10xx is the first product in the Quark family of SoCs. It is an IA-32
Do not use this mode under an IDE like Eclipse as it caches values of
previously shown varibles.
-@anchor{usingopenocdsmpwithgdb}
-@section Using OpenOCD SMP with GDB
-@cindex SMP
-For SMP support following GDB serial protocol packet have been defined :
-@itemize @bullet
-@item j - smp status request
-@item J - smp set request
-@end itemize
-
-OpenOCD implements :
-@itemize @bullet
-@item @option{jc} packet for reading core id displayed by
-GDB connection. Reply is @option{XXXXXXXX} (8 hex digits giving core id) or
- @option{E01} for target not smp.
-@item @option{JcXXXXXXXX} (8 hex digits) packet for setting core id displayed at next GDB continue
-(core id -1 is reserved for returning to normal resume mode). Reply @option{E01}
-for target not smp or @option{OK} on success.
-@end itemize
-
-Handling of this packet within GDB can be done :
-@itemize @bullet
-@item by the creation of an internal variable (i.e @option{_core}) by mean
-of function allocate_computed_value allowing following GDB command.
-@example
-set $_core 1
-#Jc01 packet is sent
-print $_core
-#jc packet is sent and result is affected in $
-@end example
-
-@item by the usage of GDB maintenance command as described in following example (2 cpus in SMP with
-core id 0 and 1 @pxref{definecputargetsworkinginsmp,,Define CPU targets working in SMP}).
-
-@example
-# toggle0 : force display of coreid 0
-define toggle0
-maint packet Jc0
-continue
-main packet Jc-1
-end
-# toggle1 : force display of coreid 1
-define toggle1
-maint packet Jc1
-continue
-main packet Jc-1
-end
-@end example
-@end itemize
-
@section RTOS Support
@cindex RTOS Support
@anchor{gdbrtossupport}
@item @option{mqx}
@item @option{uCOS-III}
@item @option{nuttx}
+@item @option{hwthread} (This is not an actual RTOS. @xref{usingopenocdsmpwithgdb,,Using OpenOCD SMP with GDB}.)
@end itemize
-@quotation Note
Before an RTOS can be detected, it must export certain symbols; otherwise, it cannot
be used by OpenOCD. Below is a list of the required symbols for each supported RTOS.
-@end quotation
@table @code
@item eCos symbols
contrib/rtos-helpers/uCOS-III-openocd.c
@end table
+@anchor{usingopenocdsmpwithgdb}
+@section Using OpenOCD SMP with GDB
+@cindex SMP
+@cindex RTOS
+@cindex hwthread
+OpenOCD includes a pseudo RTOS called @emph{hwthread} that presents CPU cores
+("hardware threads") in an SMP system as threads to GDB. With this extension,
+GDB can be used to inspect the state of an SMP system in a natural way.
+After halting the system, using the GDB command @command{info threads} will
+list the context of each active CPU core in the system. GDB's @command{thread}
+command can be used to switch the view to a different CPU core.
+The @command{step} and @command{stepi} commands can be used to step a specific core
+while other cores are free-running or remain halted, depending on the
+scheduler-locking mode configured in GDB.
+
+@section Legacy SMP core switching support
+@quotation Note
+This method is deprecated in favor of the @emph{hwthread} pseudo RTOS.
+@end quotation
+
+For SMP support following GDB serial protocol packet have been defined :
+@itemize @bullet
+@item j - smp status request
+@item J - smp set request
+@end itemize
+
+OpenOCD implements :
+@itemize @bullet
+@item @option{jc} packet for reading core id displayed by
+GDB connection. Reply is @option{XXXXXXXX} (8 hex digits giving core id) or
+ @option{E01} for target not smp.
+@item @option{JcXXXXXXXX} (8 hex digits) packet for setting core id displayed at next GDB continue
+(core id -1 is reserved for returning to normal resume mode). Reply @option{E01}
+for target not smp or @option{OK} on success.
+@end itemize
+
+Handling of this packet within GDB can be done :
+@itemize @bullet
+@item by the creation of an internal variable (i.e @option{_core}) by mean
+of function allocate_computed_value allowing following GDB command.
+@example
+set $_core 1
+#Jc01 packet is sent
+print $_core
+#jc packet is sent and result is affected in $
+@end example
+
+@item by the usage of GDB maintenance command as described in following example (2 cpus in SMP with
+core id 0 and 1 @pxref{definecputargetsworkinginsmp,,Define CPU targets working in SMP}).
+
+@example
+# toggle0 : force display of coreid 0
+define toggle0
+maint packet Jc0
+continue
+main packet Jc-1
+end
+# toggle1 : force display of coreid 1
+define toggle1
+maint packet Jc1
+continue
+main packet Jc-1
+end
+@end example
+@end itemize
+
@node Tcl Scripting API
@chapter Tcl Scripting API
@cindex Tcl Scripting API