@item the current directory,
@item any search dir specified on the command line using the @option{-s} option,
@item any search dir specified using the @command{add_script_search_dir} command,
-@item @file{$HOME/.openocd} (not on Windows),
@item a directory in the @env{OPENOCD_SCRIPTS} environment variable (if set),
+@item @file{%APPDATA%/OpenOCD} (only on Windows),
+@item @file{$HOME/Library/Preferences/org.openocd} (only on Darwin),
+@item @file{$XDG_CONFIG_HOME/openocd} (@env{$XDG_CONFIG_HOME} defaults to @file{$HOME/.config}),
+@item @file{$HOME/.openocd},
@item the site wide script library @file{$pkgdatadir/site} and
@item the OpenOCD-supplied script library @file{$pkgdatadir/scripts}.
@end enumerate
Use this option to override, for this target only, the global parameter set with
command @command{gdb_port}.
@xref{gdb_port,,command gdb_port}.
+
+@item @code{-gdb-max-connections} @var{number} -- EXPERIMENTAL: set the maximum
+number of GDB connections that are allowed for the target. Default is 1.
+A negative value for @var{number} means unlimited connections.
+See @xref{gdbmeminspect,,Using GDB as a non-intrusive memory inspector}.
@end itemize
@end deffn
CTI instance attached to it. OpenOCD has limited support for CTI using
the @emph{cti} group of commands.
-@deffn Command {cti create} cti_name @option{-dap} dap_name @option{-ap-num} apn @option{-ctibase} base_address
+@deffn Command {cti create} cti_name @option{-dap} dap_name @option{-ap-num} apn @option{-baseaddr} base_address
Creates a CTI instance @var{cti_name} on the DAP instance @var{dap_name} on MEM-AP
@var{apn}. The @var{base_address} must match the base address of the CTI
on the respective MEM-AP. All arguments are mandatory. This creates a
@cindex ITM
@cindex ETM
-@deffn Command {tpiu config} (@option{disable} | ((@option{external} | @option{internal (@var{filename} | -)}) @
+@deffn Command {tpiu config} (@option{disable} | ((@option{external} | @option{internal (@var{filename} | @var{:port} | -)}) @
(@option{sync @var{port_width}} | ((@option{manchester} | @option{uart}) @var{formatter_enable})) @
@var{TRACECLKIN_freq} [@var{trace_freq}]))
@itemize @minus
@item @option{disable} disable TPIU handling;
@item @option{external} configure TPIU to let user capture trace
-output externally (with an additional UART or logic analyzer hardware);
-@item @option{internal @var{filename}} configure TPIU and debug adapter to
-gather trace data and append it to @var{filename} (which can be
-either a regular file or a named pipe);
-@item @option{internal -} configure TPIU and debug adapter to
-gather trace data, but not write to any file. Useful in conjunction with the @command{tcl_trace} command;
+output externally (with an additional UART or logic analyzer hardware).
+@item @option{internal (@var{filename} | @var{:port} | -)} configure TPIU and debug adapter to
+gather trace data then:
+
+@itemize @minus
+@item append it to a regular file or a named pipe if @var{filename} is specified.
+@item listen to a TCP/IP port if @var{:port} is specified, then broadcast the trace data over this port.
+@item if '-' is specified, OpenOCD will forward trace data to @command{tcl_trace} command.
+@*@b{Note:} while broadcasting to file or TCP, the forwarding to @command{tcl_trace} will remain active.
+@end itemize
+
@item @option{sync @var{port_width}} use synchronous parallel trace output
-mode, and set port width to @var{port_width};
+mode, and set port width to @var{port_width}.
@item @option{manchester} use asynchronous SWO mode with Manchester
-coding;
+coding.
@item @option{uart} use asynchronous SWO mode with NRZ (same as
-regular UART 8N1) coding;
+regular UART 8N1) coding.
@item @var{formatter_enable} is @option{on} or @option{off} to enable
or disable TPIU formatter which needs to be used when both ITM and ETM
-data is to be output via SWO;
+data is to be output via SWO.
@item @var{TRACECLKIN_freq} this should be specified to match target's
-current TRACECLKIN frequency (usually the same as HCLK);
+current TRACECLKIN frequency (usually the same as HCLK).
@item @var{trace_freq} trace port frequency. Can be omitted in
internal mode to let the adapter driver select the maximum supported
rate automatically.
@end deffn
@deffn Command {riscv set_prefer_sba} on|off
-When on, prefer to use System Bus Access to access memory. When off, prefer to
-use the Program Buffer to access memory.
+When on, prefer to use System Bus Access to access memory. When off (default),
+prefer to use the Program Buffer to access memory.
+@end deffn
+
+@deffn Command {riscv set_enable_virtual} on|off
+When on, memory accesses are performed on physical or virtual memory depending
+on the current system configuration. When off (default), all memory accessses are performed
+on physical memory.
+@end deffn
+
+@deffn Command {riscv set_enable_virt2phys} on|off
+When on (default), memory accesses are performed on physical or virtual memory
+depending on the current satp configuration. When off, all memory accessses are
+performed on physical memory.
+@end deffn
+
+@deffn Command {riscv resume_order} normal|reversed
+Some software assumes all harts are executing nearly continuously. Such
+software may be sensitive to the order that harts are resumed in. On harts
+that don't support hasel, this option allows the user to choose the order the
+harts are resumed in. If you are using this option, it's probably masking a
+race condition problem in your code.
+
+Normal order is from lowest hart index to highest. This is the default
+behavior. Reversed order is from highest hart index to lowest.
@end deffn
@deffn Command {riscv set_ir} (@option{idcode}|@option{dtmcs}|@option{dmi}) [value]
and DBUS registers, respectively.
@end deffn
+@deffn Command {riscv use_bscan_tunnel} value
+Enable or disable use of a BSCAN tunnel to reach DM. Supply the width of
+the DM transport TAP's instruction register to enable. Supply a value of 0 to disable.
+@end deffn
+
+@deffn Command {riscv set_ebreakm} on|off
+Control dcsr.ebreakm. When on (default), M-mode ebreak instructions trap to
+OpenOCD. When off, they generate a breakpoint exception handled internally.
+@end deffn
+
+@deffn Command {riscv set_ebreaks} on|off
+Control dcsr.ebreaks. When on (default), S-mode ebreak instructions trap to
+OpenOCD. When off, they generate a breakpoint exception handled internally.
+@end deffn
+
+@deffn Command {riscv set_ebreaku} on|off
+Control dcsr.ebreaku. When on (default), U-mode ebreak instructions trap to
+OpenOCD. When off, they generate a breakpoint exception handled internally.
+@end deffn
+
@subsection RISC-V Authentication Commands
The following commands can be used to authenticate to a RISC-V system. Eg. a
The following commands allow direct access to the Debug Module Interface, which
can be used to interact with custom debug features.
-@deffn Command {riscv dmi_read}
+@deffn Command {riscv dmi_read} address
Perform a 32-bit DMI read at address, returning the value.
@end deffn
and GDB would require stopping the target to get the prompt back.
Do not use this mode under an IDE like Eclipse as it caches values of
-previously shown varibles.
+previously shown variables.
+
+It's also possible to connect more than one GDB to the same target by the
+target's configuration option @code{-gdb-max-connections}. This allows, for
+example, one GDB to run a script that continuously polls a set of variables
+while other GDB can be used interactively. Be extremely careful in this case,
+because the two GDB can easily get out-of-sync.
@section RTOS Support
@cindex RTOS Support
Code Review / openocd.git / blobdiff