connected to a PC's EPP mode parallel port.
This defines some driver-specific commands:
-@deffn {Config Command} {parport_port} number
+@deffn {Config Command} {parport port} number
Specifies either the address of the I/O port (default: 0x378 for LPT1) or
the number of the @file{/dev/parport} device.
@end deffn
Gateworks GW16012 JTAG programmer.
This has one driver-specific command:
-@deffn {Config Command} {parport_port} [port_number]
+@deffn {Config Command} {parport port} [port_number]
Display either the address of the I/O port
(default: 0x378 for LPT1) or the number of the @file{/dev/parport} device.
If a parameter is provided, first switch to use that port.
These interfaces have several commands, used to configure the driver
before initializing the JTAG scan chain:
-@deffn {Config Command} {parport_cable} name
+@deffn {Config Command} {parport cable} name
Set the layout of the parallel port cable used to connect to the target.
This is a write-once setting.
Currently valid cable @var{name} values include:
@end itemize
@end deffn
-@deffn {Config Command} {parport_port} [port_number]
+@deffn {Config Command} {parport port} [port_number]
Display either the address of the I/O port
(default: 0x378 for LPT1) or the number of the @file{/dev/parport} device.
If a parameter is provided, first switch to use that port.
This is a write-once setting.
When using PPDEV to access the parallel port, use the number of the parallel port:
-@option{parport_port 0} (the default). If @option{parport_port 0x378} is specified
+@option{parport port 0} (the default). If @option{parport port 0x378} is specified
you may encounter a problem.
@end deffn
-@deffn {Config Command} {parport_toggling_time} [nanoseconds]
+@deffn {Config Command} {parport toggling_time} [nanoseconds]
Displays how many nanoseconds the hardware needs to toggle TCK;
the parport driver uses this value to obey the
@command{adapter speed} configuration.
To measure the toggling time with a logic analyzer or a digital storage
oscilloscope, follow the procedure below:
@example
-> parport_toggling_time 1000
+> parport toggling_time 1000
> adapter speed 500
@end example
This sets the maximum JTAG clock speed of the hardware, but
large set of samples.
Update the setting to match your measurement:
@example
-> parport_toggling_time <measured nanoseconds>
+> parport toggling_time <measured nanoseconds>
@end example
Now the clock speed will be a better match for @command{adapter speed}
command given in OpenOCD scripts and event handlers.
@end quotation
@end deffn
-@deffn {Config Command} {parport_write_on_exit} (@option{on}|@option{off})
+@deffn {Config Command} {parport write_on_exit} (@option{on}|@option{off})
This will configure the parallel driver to write a known
cable-specific value to the parallel interface on exiting OpenOCD.
@end deffn
@example
adapter driver parport
-parport_port 0x278
-parport_cable wiggler
+parport port 0x278
+parport cable wiggler
@end example
@end deffn
See @file{interface/raspberrypi-native.cfg} for a sample config and
pinout.
+@deffn {Config Command} {bcm2835gpio_jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
+Set JTAG transport GPIO numbers for TCK, TMS, TDI, and TDO (in that order).
+Must be specified to enable JTAG transport. These pins can also be specified
+individually.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_tck_num} @var{tck}
+Set TCK GPIO number. Must be specified to enable JTAG transport. Can also be
+specified using the configuration command bcm2835gpio_jtag_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_tms_num} @var{tms}
+Set TMS GPIO number. Must be specified to enable JTAG transport. Can also be
+specified using the configuration command bcm2835gpio_jtag_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_tdo_num} @var{tdo}
+Set TDO GPIO number. Must be specified to enable JTAG transport. Can also be
+specified using the configuration command bcm2835gpio_jtag_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_tdi_num} @var{tdi}
+Set TDI GPIO number. Must be specified to enable JTAG transport. Can also be
+specified using the configuration command bcm2835gpio_jtag_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_swd_nums} @var{swclk} @var{swdio}
+Set SWD transport GPIO numbers for SWCLK and SWDIO (in that order). Must be
+specified to enable SWD transport. These pins can also be specified individually.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_swclk_num} @var{swclk}
+Set SWCLK GPIO number. Must be specified to enable SWD transport. Can also be
+specified using the configuration command bcm2835gpio_swd_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_swdio_num} @var{swdio}
+Set SWDIO GPIO number. Must be specified to enable SWD transport. Can also be
+specified using the configuration command bcm2835gpio_swd_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_swdio_dir_num} @var{swdio} @var{dir}
+Set SWDIO direction control pin GPIO number. If specified, this pin can be used
+to control the direction of an external buffer on the SWDIO pin (set=output
+mode, clear=input mode). If not specified, this feature is disabled.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_srst_num} @var{srst}
+Set SRST GPIO number. Must be specified to enable SRST.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_trst_num} @var{trst}
+Set TRST GPIO number. Must be specified to enable TRST.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_speed_coeffs} @var{speed_coeff} @var{speed_offset}
+Set SPEED_COEFF and SPEED_OFFSET for delay calculations. If unspecified,
+speed_coeff defaults to 113714, and speed_offset defaults to 28.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_peripheral_base} @var{base}
+Set the peripheral base register address to access GPIOs. For the RPi1, use
+0x20000000. For RPi2 and RPi3, use 0x3F000000. For RPi4, use 0xFE000000. A full
+list can be found in the
+@uref{https://www.raspberrypi.org/documentation/hardware/raspberrypi/peripheral_addresses.md, official guide}.
+@end deffn
+
@end deffn
@deffn {Interface Driver} {imx_gpio}
Code Review / openocd.git / blobdiff