Use a command group 'kitprog' with subcommands instead of individual
commands with 'kitprog_' prefix.
The old command is still available to ensure backwards compatibility,
but is marked as deprecated.
Change-Id: I7f0d447939819ffc488a3d7a8de672b58887127f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7967
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
SWD-only adapter that is designed to be used with Cypress's PSoC and PRoC device
families, but it is possible to use it with some other devices. If you are using
this adapter with a PSoC or a PRoC, you may need to add
SWD-only adapter that is designed to be used with Cypress's PSoC and PRoC device
families, but it is possible to use it with some other devices. If you are using
this adapter with a PSoC or a PRoC, you may need to add
-@command{kitprog_init_acquire_psoc} or @command{kitprog acquire_psoc} to your
+@command{kitprog init_acquire_psoc} or @command{kitprog acquire_psoc} to your
configuration script.
Note that this driver is for the proprietary KitProg protocol, not the CMSIS-DAP
configuration script.
Note that this driver is for the proprietary KitProg protocol, not the CMSIS-DAP
SWD sequence must be sent after every target reset in order to re-establish
communications with the target.
@item Due in part to the limitation above, KitProg devices with firmware below
SWD sequence must be sent after every target reset in order to re-establish
communications with the target.
@item Due in part to the limitation above, KitProg devices with firmware below
-version 2.14 will need to use @command{kitprog_init_acquire_psoc} in order to
+version 2.14 will need to use @command{kitprog init_acquire_psoc} in order to
communicate with PSoC 5LP devices. This is because, assuming debug is not
disabled on the PSoC, the PSoC 5LP needs its JTAG interface switched to SWD
mode before communication can begin, but prior to firmware 2.14, "JTAG to SWD"
could only be sent with an acquisition sequence.
@end itemize
communicate with PSoC 5LP devices. This is because, assuming debug is not
disabled on the PSoC, the PSoC 5LP needs its JTAG interface switched to SWD
mode before communication can begin, but prior to firmware 2.14, "JTAG to SWD"
could only be sent with an acquisition sequence.
@end itemize
-@deffn {Config Command} {kitprog_init_acquire_psoc}
+@deffn {Config Command} {kitprog init_acquire_psoc}
Indicate that a PSoC acquisition sequence needs to be run during adapter init.
Please be aware that the acquisition sequence hard-resets the target.
@end deffn
Indicate that a PSoC acquisition sequence needs to be run during adapter init.
Please be aware that the acquisition sequence hard-resets the target.
@end deffn
.usage = "",
.help = "try to acquire a PSoC",
},
.usage = "",
.help = "try to acquire a PSoC",
},
+ {
+ .name = "init_acquire_psoc",
+ .handler = &kitprog_handle_init_acquire_psoc_command,
+ .mode = COMMAND_CONFIG,
+ .help = "try to acquire a PSoC during init",
+ .usage = "",
+ },
COMMAND_REGISTRATION_DONE
};
COMMAND_REGISTRATION_DONE
};
.usage = "<cmd>",
.chain = kitprog_subcommand_handlers,
},
.usage = "<cmd>",
.chain = kitprog_subcommand_handlers,
},
- {
- .name = "kitprog_init_acquire_psoc",
- .handler = &kitprog_handle_init_acquire_psoc_command,
- .mode = COMMAND_CONFIG,
- .help = "try to acquire a PSoC during init",
- .usage = "",
- },
COMMAND_REGISTRATION_DONE
};
COMMAND_REGISTRATION_DONE
};
eval cmsis-dap usb $args
}
eval cmsis-dap usb $args
}
+lappend _telnet_autocomplete_skip "kitprog_init_acquire_psoc"
+proc "kitprog_init_acquire_psoc" {} {
+ echo "DEPRECATED! use 'kitprog init_acquire_psoc', not 'kitprog_init_acquire_psoc'"
+ eval kitprog init_acquire_psoc
+}
+
lappend _telnet_autocomplete_skip "pld device"
proc "pld device" {driver tap_name {opt 0}} {
echo "DEPRECATED! use 'pld create ...', not 'pld device ...'"
lappend _telnet_autocomplete_skip "pld device"
proc "pld device" {driver tap_name {opt 0}} {
echo "DEPRECATED! use 'pld create ...', not 'pld device ...'"
Linking to existing account procedure
If you already have an account and want to add another login method
you
MUST first sign in with your existing account and
then change URL to read
https://review.openocd.org/login/?link
to get to this page again but this time it'll work for linking. Thank you.
SSH host keys fingerprints
1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=.. |
|+o.. . |
|*.o . . |
|+B . . . |
|Bo. = o S |
|Oo.+ + = |
|oB=.* = . o |
| =+=.+ + E |
|. .=o . o |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)