target: Remove "-variant" argument

[openocd.git] / tcl / target / stm32l.cfg

diff --git a/tcl/target/stm32l.cfg b/tcl/target/stm32l.cfg
index 5c3d3686f4ad6a7ac60160263ed6219dfd06b7bc..27ebf828d50f9553f8f65c411eab7ae8ba21218c 100644 (file)
--- a/tcl/target/stm32l.cfg
+++ b/tcl/target/stm32l.cfg
@@ -1,43 +1,55 @@
 # script for stm32l
 
+#
+# stm32 devices support both JTAG and SWD transports.
+#
+source [find target/swj-dp.tcl]
+
 if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
+   set _CHIPNAME $CHIPNAME
 } else {
-   set  _CHIPNAME stm32l
+   set _CHIPNAME stm32l
 }
 
 if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
+   set _ENDIAN $ENDIAN
 } else {
-   set  _ENDIAN little
+   set _ENDIAN little
 }
 
 # Work-area is a space in RAM used for flash programming
-# By default use 14kB
+# By default use 10kB
 if { [info exists WORKAREASIZE] } {
-   set  _WORKAREASIZE $WORKAREASIZE
+   set _WORKAREASIZE $WORKAREASIZE
 } else {
-   set  _WORKAREASIZE 0x3800
+   set _WORKAREASIZE 0x2800
 }
 
 # JTAG speed should be <= F_CPU/6.
 # F_CPU after reset is 2MHz, so use F_JTAG max = 333kHz
-adapter_khz 100
+adapter_khz 300
 
 adapter_nsrst_delay 100
-jtag_ntrst_delay 100
+if {[using_jtag]} {
+ jtag_ntrst_delay 100
+}
 
 #jtag scan chain
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
-  # See STM Document RM0038
-  # Section 24.6.3
-   set _CPUTAPID 0x4ba00477
+   if { [using_jtag] } {
+      # See STM Document RM0038
+      # Section 24.6.3
+      set _CPUTAPID 0x4ba00477
+   } {
+      set _CPUTAPID 0x2ba01477
+   }
 }
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
-if { [info exists BSTAPID ] } {
+swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+if { [info exists BSTAPID] } {
    # FIXME this never gets used to override defaults...
    set _BSTAPID $BSTAPID
 } else {
@@ -45,21 +57,25 @@ if { [info exists BSTAPID ] } {
   # Section 24.6.2
   set _BSTAPID 0x06416041
 }
-jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
+
+if {[using_jtag]} {
+ swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
+}
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
-
 # flash size will be probed
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32lx 0x08000000 0 0 0 $_TARGETNAME
 
-# if srst is not fitted use SYSRESETREQ to
-# perform a soft reset
-cortex_m3 reset_config sysresetreq
+if {![using_hla]} {
+   # if srst is not fitted use SYSRESETREQ to
+   # perform a soft reset
+   cortex_m reset_config sysresetreq
+}
 
 proc stm32l_enable_HSI {} {
        # Enable HSI as clock source
@@ -79,3 +95,6 @@ $_TARGETNAME configure -event reset-init {
        stm32l_enable_HSI
 }
 
+$_TARGETNAME configure -event reset-start {
+       adapter_khz 300
+}