# script for str9
-# jtag speed. We need to stick to 16kHz until we've finished reset.
-
-jtag_khz 16
-proc target_0_pre_reset {} {
- jtag_khz 16
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME str912
}
-proc target_0_post_reset {} {
- # We can increase speed now that we know the target is halted.
- jtag_khz 3000
-
- # -- Enable 96K RAM
- # PFQBC enabled / DTCM & AHB wait-states disabled
- mww 0x5C002034 0x0191
-
- str9x flash_config 0 4 2 0 0x80000
- flash protect 0 0 7 off
-
-
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
+ set _ENDIAN little
}
+# jtag speed. We need to stick to 16kHz until we've finished reset.
+jtag_rclk 16
jtag_nsrst_delay 100
jtag_ntrst_delay 100
#use combined on interfaces or targets that can't set TRST/SRST separately
reset_config trst_and_srst
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 8 0x1 0x1 0xfe
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
+if { [info exists FLASHTAPID ] } {
+ set _FLASHTAPID $FLASHTAPID
+} else {
+ set _FLASHTAPID 0x04570041
+}
+jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
+
+if { [info exists CPUTAPID ] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ set _CPUTAPID 0x25966041
+}
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
-#target <type> <startup mode>
-#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm966e little 1 arm966e
+if { [info exists BSTAPID ] } {
+ set _BSTAPID $BSTAPID
+} else {
+ set _BSTAPID 0x1457f041
+}
+jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
+
+$_TARGETNAME configure -event reset-start { jtag_rclk 16 }
+
+$_TARGETNAME configure -event reset-init {
+ # We can increase speed now that we know the target is halted.
+ #jtag_rclk 3000
+
+ # -- Enable 96K RAM
+ # PFQBC enabled / DTCM & AHB wait-states disabled
+ mww 0x5C002034 0x0191
+ str9x flash_config 0 4 2 0 0x80000
+ flash protect 0 0 7 off
+}
-working_area 0 0x50000000 16384 nobackup
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
#flash bank str9x <base> <size> 0 0 <target#> <variant>
flash bank str9x 0x00000000 0x00080000 0 0 0