Dick Hollenbeck <dick@softplc.com> moved stuff into openocd.c - should never have...

[openocd.git] / src / target / target / imx31.cfg

diff --git a/src/target/target/imx31.cfg b/src/target/target/imx31.cfg
index 34b35d8ba62ab35da05e9beb2e0fa8198839e7ac..3fed2f820316cc2215d7a975a057a92238708670 100644 (file)
--- a/src/target/target/imx31.cfg
+++ b/src/target/target/imx31.cfg
@@ -1,19 +1,62 @@
 # imx31 config
 #
-# NB! Does not work yet. Work in progress
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-# 4 devices otherwise openocd complains, the last one returns 0x0 for all bytes
-jtag_device 4 0x1 0x0 0xe
-jtag_device 5 0x1 0x1f 0x1e
-#jtag_device 4 0x0 0x0 0xe
-# The device below does not have an IDCODE, so lsb is 1
-jtag_device 4 0x0 0x0 0xf
-jtag_device 5 0x1 0x0 0x1e
-
-jtag_nsrst_delay 500
-jtag_ntrst_delay 500
-
-target create target0 arm11 -endian little -chain-position 1
- 
+
+reset_config trst_and_srst
+
+if { [info exists CHIPNAME] } {        
+   set  _CHIPNAME $CHIPNAME    
+} else {        
+   set  _CHIPNAME imx31
+}
+
+if { [info exists ENDIAN] } {  
+   set  _ENDIAN $ENDIAN    
+} else {        
+   set  _ENDIAN little
+}
+
+if { [info exists CPUTAPID ] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   set _CPUTAPID 0x07b3601d
+}
+
+if { [info exists SDMATAPID ] } {
+   set _SDMATAPID $SDMATAPID
+} else {
+   set _SDMATAPID 0x2190101d
+}
+
+#========================================
+# The "system jtag controller" 
+# IMX31 reference manual, page 6-28 - figure 6-14
+if { [info exists SJCTAPID ] } {
+   set _SJCTAPID $SJCTAPID
+} else {
+   set _SJCTAPID 0x2b900f0f
+}
+jtag newtap $_CHIPNAME sjc -irlen 4 -ircapture 0x0 -irmask 0x0 -expected-id $_SJCTAPID
+
+# The "SDMA" - <S>mart <DMA> controller debug tap
+# Based on some IO pins - this can be disabled & removed
+# See diagram: 6-14
+#   SIGNAL NAME:
+#    SJC_MOD - controls multiplexer - disables ARM1136
+#    SDMA_BYPASS - disables SDMA    - 
+#  
+# Per ARM: DDI0211J_arm1136_r1p5_trm.pdf - the ARM 1136 as a 5 bit IR register
+jtag newtap $_CHIPNAME cpu -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_CPUTAPID
+
+# No IDCODE for this TAP
+jtag newtap $_CHIPNAME whatchacallit -irlen 4 -ircapture 0 -irmask 0xf -expected-id 0x0
+
+# Per section 40.17.1, table 40-85 the IR register is 4 bits
+# But this conflicts with Diagram 6-13, "3bits ir and drs"
+jtag newtap $_CHIPNAME smda -irlen 5 -ircapture 0x1 -irmask 0x1f -expected-id $_SDMATAPID
+
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME arm11 -endian $_ENDIAN -chain-position $_TARGETNAME
+
+
+proc power_restore {} { puts "Sensed power restore. No action." } 
+proc srst_deasserted {} { puts "Sensed nSRST deasserted. No action." }