return retval;
if (target->dbg_msg_enabled) {
- /* restore DCB_DCRDR - this needs to be in a seperate
+ /* restore DCB_DCRDR - this needs to be in a separate
* transaction otherwise the emulated DCC channel breaks */
if (retval == ERROR_OK)
retval = mem_ap_write_atomic_u32(armv7m->debug_ap, DCB_DCRDR, dcrdr);
struct armv7m_common *armv7m = &cortex_m->armv7m;
/* mask off status bits */
- cortex_m->dcb_dhcsr &= ~((0xFFFF << 16) | mask_off);
+ cortex_m->dcb_dhcsr &= ~((0xFFFFul << 16) | mask_off);
/* create new register mask */
cortex_m->dcb_dhcsr |= DBGKEY | C_DEBUGEN | mask_on;
uint32_t dcb_dhcsr = 0;
int retval, timeout = 0;
- /* soft_reset_halt is deprecated on cortex_m as the same functionality
- * can be obtained by using 'reset halt' and 'cortex_m reset_config vectreset'
- * As this reset only used VC_CORERESET it would only ever reset the cortex_m
+ /* on single cortex_m MCU soft_reset_halt should be avoided as same functionality
+ * can be obtained by using 'reset halt' and 'cortex_m reset_config vectreset'.
+ * As this reset only uses VC_CORERESET it would only ever reset the cortex_m
* core, not the peripherals */
- LOG_WARNING("soft_reset_halt is deprecated, please use 'reset halt' instead.");
+ LOG_DEBUG("soft_reset_halt is discouraged, please use 'reset halt' instead.");
+
+ /* Set C_DEBUGEN */
+ retval = cortex_m_write_debug_halt_mask(target, 0, C_STEP | C_MASKINTS);
+ if (retval != ERROR_OK)
+ return retval;
/* Enter debug state on reset; restore DEMCR in endreset_event() */
retval = mem_ap_write_u32(armv7m->debug_ap, DCB_DEMCR,
* a normal step, otherwise we have to manually step over the bkpt
* instruction - as such simulate a step */
if (bkpt_inst_found == false) {
- if ((cortex_m->isrmasking_mode != CORTEX_M_ISRMASK_AUTO)) {
+ if (cortex_m->isrmasking_mode != CORTEX_M_ISRMASK_AUTO) {
/* Automatic ISR masking mode off: Just step over the next
* instruction, with interrupts on or off as appropriate. */
cortex_m_set_maskints_for_step(target);
* just step over the instruction with interrupts disabled.
*
* The documentation has no information about this, it was found by observation
- * on STM32F1 and STM32F2. Proper explanation welcome. STM32F0 dosen't seem to
+ * on STM32F1 and STM32F2. Proper explanation welcome. STM32F0 doesn't seem to
* suffer from this problem.
*
* To add some confusion: pc_value has bit 0 always set, while the breakpoint
/* Re-enable interrupts if appropriate */
cortex_m_write_debug_halt_mask(target, C_HALT, 0);
cortex_m_set_maskints_for_halt(target);
- }
- else {
+ } else {
/* Set a temporary break point */
if (breakpoint) {
{
struct dwt_reg_state *state;
- state = calloc(1, sizeof *state);
+ state = calloc(1, sizeof(*state));
if (!state)
return;
state->addr = d->addr;
return;
}
- cache = calloc(1, sizeof *cache);
+ cache = calloc(1, sizeof(*cache));
if (!cache) {
fail1:
free(cm->dwt_comparator_list);
}
cache->name = "Cortex-M DWT registers";
cache->num_regs = 2 + cm->dwt_num_comp * 3;
- cache->reg_list = calloc(cache->num_regs, sizeof *cache->reg_list);
+ cache->reg_list = calloc(cache->num_regs, sizeof(*cache->reg_list));
if (!cache->reg_list) {
free(cache);
goto fail1;
armv7m->debug_ap->tar_autoincr_block = (1 << 10);
}
+ /* Enable debug requests */
+ retval = target_read_u32(target, DCB_DHCSR, &cortex_m->dcb_dhcsr);
+ if (retval != ERROR_OK)
+ return retval;
+ if (!(cortex_m->dcb_dhcsr & C_DEBUGEN)) {
+ uint32_t dhcsr = (cortex_m->dcb_dhcsr | C_DEBUGEN) & ~(C_HALT | C_STEP | C_MASKINTS);
+
+ retval = target_write_u32(target, DCB_DHCSR, DBGKEY | (dhcsr & 0x0000FFFFUL));
+ if (retval != ERROR_OK)
+ return retval;
+ cortex_m->dcb_dhcsr = dhcsr;
+ }
+
/* Configure trace modules */
retval = target_write_u32(target, DCB_DEMCR, TRCENA | armv7m->demcr);
if (retval != ERROR_OK)