+// SPDX-License-Identifier: GPL-2.0-or-later
+
/***************************************************************************
*
* Copyright (C) 2010 by David Brownell
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
***************************************************************************/
/**
* is a transport level interface, with "target/arm_adi_v5.[hc]" code
* understanding operation semantics, shared with the JTAG transport.
*
- * Single-DAP support only.
+ * Single DAP and multidrop-SWD support.
*
* for details, see "ARM IHI 0031A"
* ARM Debug Interface v5 Architecture Specification
* especially section 5.3 for SWD protocol
+ * and "ARM IHI 0074C" ARM Debug Interface Architecture Specification ADIv6.0
*
* On many chips (most current Cortex-M3 parts) SWD is a run-time alternative
* to JTAG. Boards may support one or both. There are also SWD-only chips,
/* for debug, set do_sync to true to force synchronous transfers */
static bool do_sync;
+static struct adiv5_dap *swd_multidrop_selected_dap;
+
+
+static int swd_queue_dp_write_inner(struct adiv5_dap *dap, unsigned int reg,
+ uint32_t data);
+
+
+static int swd_send_sequence(struct adiv5_dap *dap, enum swd_special_seq seq)
+{
+ const struct swd_driver *swd = adiv5_dap_swd_driver(dap);
+ assert(swd);
+
+ return swd->switch_seq(seq);
+}
+
static void swd_finish_read(struct adiv5_dap *dap)
{
const struct swd_driver *swd = adiv5_dap_swd_driver(dap);
}
}
-static int swd_queue_dp_write(struct adiv5_dap *dap, unsigned reg,
- uint32_t data);
-static int swd_queue_dp_read(struct adiv5_dap *dap, unsigned reg,
- uint32_t *data);
-
static void swd_clear_sticky_errors(struct adiv5_dap *dap)
{
const struct swd_driver *swd = adiv5_dap_swd_driver(dap);
return retval;
}
-static int swd_connect(struct adiv5_dap *dap)
+static inline int check_sync(struct adiv5_dap *dap)
+{
+ return do_sync ? swd_run_inner(dap) : ERROR_OK;
+}
+
+/** Select the DP register bank matching bits 7:4 of reg. */
+static int swd_queue_dp_bankselect(struct adiv5_dap *dap, unsigned int reg)
+{
+ /* Only register address 0 and 4 are banked. */
+ if ((reg & 0xf) > 4)
+ return ERROR_OK;
+
+ uint64_t sel = (reg & 0x000000F0) >> 4;
+ if (dap->select != DP_SELECT_INVALID)
+ sel |= dap->select & ~0xfULL;
+
+ if (sel == dap->select)
+ return ERROR_OK;
+
+ dap->select = sel;
+
+ int retval = swd_queue_dp_write_inner(dap, DP_SELECT, (uint32_t)sel);
+ if (retval != ERROR_OK)
+ dap->select = DP_SELECT_INVALID;
+
+ return retval;
+}
+
+static int swd_queue_dp_read_inner(struct adiv5_dap *dap, unsigned int reg,
+ uint32_t *data)
{
const struct swd_driver *swd = adiv5_dap_swd_driver(dap);
- uint32_t dpidr = 0xdeadbeef;
- int status;
+ assert(swd);
- /* FIXME validate transport config ... is the
- * configured DAP present (check IDCODE)?
- * Is *only* one DAP configured?
+ int retval = swd_queue_dp_bankselect(dap, reg);
+ if (retval != ERROR_OK)
+ return retval;
+
+ swd->read_reg(swd_cmd(true, false, reg), data, 0);
+
+ return check_sync(dap);
+}
+
+static int swd_queue_dp_write_inner(struct adiv5_dap *dap, unsigned int reg,
+ uint32_t data)
+{
+ int retval;
+ const struct swd_driver *swd = adiv5_dap_swd_driver(dap);
+ assert(swd);
+
+ swd_finish_read(dap);
+
+ if (reg == DP_SELECT) {
+ dap->select = data & (ADIV5_DP_SELECT_APSEL | ADIV5_DP_SELECT_APBANK | DP_SELECT_DPBANK);
+
+ swd->write_reg(swd_cmd(false, false, reg), data, 0);
+
+ retval = check_sync(dap);
+ if (retval != ERROR_OK)
+ dap->select = DP_SELECT_INVALID;
+
+ return retval;
+ }
+
+ retval = swd_queue_dp_bankselect(dap, reg);
+ if (retval != ERROR_OK)
+ return retval;
+
+ swd->write_reg(swd_cmd(false, false, reg), data, 0);
+
+ return check_sync(dap);
+}
+
+
+static int swd_multidrop_select_inner(struct adiv5_dap *dap, uint32_t *dpidr_ptr,
+ uint32_t *dlpidr_ptr, bool clear_sticky)
+{
+ int retval;
+ uint32_t dpidr, dlpidr;
+
+ assert(dap_is_multidrop(dap));
+
+ swd_send_sequence(dap, LINE_RESET);
+ /* From ARM IHI 0074C ADIv6.0, chapter B4.3.3 "Connection and line reset
+ * sequence":
+ * - line reset sets DP_SELECT_DPBANK to zero;
+ * - read of DP_DPIDR takes the connection out of reset;
+ * - write of DP_TARGETSEL keeps the connection in reset;
+ * - other accesses return protocol error (SWDIO not driven by target).
*
- * MUST READ DPIDR
+ * Read DP_DPIDR to get out of reset. Initialize dap->select to zero to
+ * skip the write to DP_SELECT, avoiding the protocol error. Set again
+ * dap->select to DP_SELECT_INVALID because the rest of the register is
+ * unknown after line reset.
*/
+ dap->select = 0;
- /* Check if we should reset srst already when connecting, but not if reconnecting. */
- if (!dap->do_reconnect) {
- enum reset_types jtag_reset_config = jtag_get_reset_config();
+ retval = swd_queue_dp_write_inner(dap, DP_TARGETSEL, dap->multidrop_targetsel);
+ if (retval != ERROR_OK)
+ return retval;
- if (jtag_reset_config & RESET_CNCT_UNDER_SRST) {
- if (jtag_reset_config & RESET_SRST_NO_GATING)
- adapter_assert_reset();
- else
- LOG_WARNING("\'srst_nogate\' reset_config option is required");
+ retval = swd_queue_dp_read_inner(dap, DP_DPIDR, &dpidr);
+ if (retval != ERROR_OK)
+ return retval;
+
+ if (clear_sticky) {
+ /* Clear all sticky errors (including ORUN) */
+ swd_clear_sticky_errors(dap);
+ } else {
+ /* Ideally just clear ORUN flag which is set by reset */
+ retval = swd_queue_dp_write_inner(dap, DP_ABORT, ORUNERRCLR);
+ if (retval != ERROR_OK)
+ return retval;
+ }
+
+ dap->select = DP_SELECT_INVALID;
+
+ retval = swd_queue_dp_read_inner(dap, DP_DLPIDR, &dlpidr);
+ if (retval != ERROR_OK)
+ return retval;
+
+ retval = swd_run_inner(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
+ if ((dpidr & DP_DPIDR_VERSION_MASK) < (2UL << DP_DPIDR_VERSION_SHIFT)) {
+ LOG_INFO("Read DPIDR 0x%08" PRIx32
+ " has version < 2. A non multidrop capable device connected?",
+ dpidr);
+ return ERROR_FAIL;
+ }
+
+ /* TODO: check TARGETID if DLIPDR is same for more than one DP */
+ uint32_t expected_dlpidr = DP_DLPIDR_PROTVSN |
+ (dap->multidrop_targetsel & DP_TARGETSEL_INSTANCEID_MASK);
+ if (dlpidr != expected_dlpidr) {
+ LOG_INFO("Read incorrect DLPIDR 0x%08" PRIx32
+ " (possibly CTRL/STAT value)",
+ dlpidr);
+ return ERROR_FAIL;
+ }
+
+ LOG_DEBUG_IO("Selected DP_TARGETSEL 0x%08" PRIx32, dap->multidrop_targetsel);
+ swd_multidrop_selected_dap = dap;
+
+ if (dpidr_ptr)
+ *dpidr_ptr = dpidr;
+
+ if (dlpidr_ptr)
+ *dlpidr_ptr = dlpidr;
+
+ return retval;
+}
+
+static int swd_multidrop_select(struct adiv5_dap *dap)
+{
+ if (!dap_is_multidrop(dap))
+ return ERROR_OK;
+
+ if (swd_multidrop_selected_dap == dap)
+ return ERROR_OK;
+
+ int retval = ERROR_OK;
+ for (unsigned int retry = 0; ; retry++) {
+ bool clear_sticky = retry > 0;
+
+ retval = swd_multidrop_select_inner(dap, NULL, NULL, clear_sticky);
+ if (retval == ERROR_OK)
+ break;
+
+ swd_multidrop_selected_dap = NULL;
+ if (retry > 3) {
+ LOG_ERROR("Failed to select multidrop %s", adiv5_dap_name(dap));
+ return retval;
}
+
+ LOG_DEBUG("Failed to select multidrop %s, retrying...",
+ adiv5_dap_name(dap));
+ /* we going to retry localy, do not ask for full reconnect */
+ dap->do_reconnect = false;
+ }
+
+ return retval;
+}
+
+static int swd_connect_multidrop(struct adiv5_dap *dap)
+{
+ int retval;
+ uint32_t dpidr = 0xdeadbeef;
+ uint32_t dlpidr = 0xdeadbeef;
+ int64_t timeout = timeval_ms() + 500;
+
+ do {
+ swd_send_sequence(dap, JTAG_TO_DORMANT);
+ swd_send_sequence(dap, DORMANT_TO_SWD);
+
+ /* Clear link state, including the SELECT cache. */
+ dap->do_reconnect = false;
+ dap_invalidate_cache(dap);
+ swd_multidrop_selected_dap = NULL;
+
+ retval = swd_multidrop_select_inner(dap, &dpidr, &dlpidr, true);
+ if (retval == ERROR_OK)
+ break;
+
+ alive_sleep(1);
+
+ } while (timeval_ms() < timeout);
+
+ if (retval != ERROR_OK) {
+ swd_multidrop_selected_dap = NULL;
+ LOG_ERROR("Failed to connect multidrop %s", adiv5_dap_name(dap));
+ return retval;
}
+ LOG_INFO("SWD DPIDR 0x%08" PRIx32 ", DLPIDR 0x%08" PRIx32,
+ dpidr, dlpidr);
+ return retval;
+}
+
+static int swd_connect_single(struct adiv5_dap *dap)
+{
+ int retval;
+ uint32_t dpidr = 0xdeadbeef;
int64_t timeout = timeval_ms() + 500;
do {
- /* Note, debugport_init() does setup too */
- swd->switch_seq(JTAG_TO_SWD);
+ if (dap->switch_through_dormant) {
+ swd_send_sequence(dap, JTAG_TO_DORMANT);
+ swd_send_sequence(dap, DORMANT_TO_SWD);
+ } else {
+ swd_send_sequence(dap, JTAG_TO_SWD);
+ }
/* Clear link state, including the SELECT cache. */
dap->do_reconnect = false;
dap_invalidate_cache(dap);
- status = swd_queue_dp_read(dap, DP_DPIDR, &dpidr);
- if (status == ERROR_OK) {
- status = swd_run_inner(dap);
- if (status == ERROR_OK)
+ /* The sequences to enter in SWD (JTAG_TO_SWD and DORMANT_TO_SWD) end
+ * with a SWD line reset sequence (50 clk with SWDIO high).
+ * From ARM IHI 0074C ADIv6.0, chapter B4.3.3 "Connection and line reset
+ * sequence":
+ * - line reset sets DP_SELECT_DPBANK to zero;
+ * - read of DP_DPIDR takes the connection out of reset;
+ * - write of DP_TARGETSEL keeps the connection in reset;
+ * - other accesses return protocol error (SWDIO not driven by target).
+ *
+ * Read DP_DPIDR to get out of reset. Initialize dap->select to zero to
+ * skip the write to DP_SELECT, avoiding the protocol error. Set again
+ * dap->select to DP_SELECT_INVALID because the rest of the register is
+ * unknown after line reset.
+ */
+ dap->select = 0;
+ retval = swd_queue_dp_read_inner(dap, DP_DPIDR, &dpidr);
+ if (retval == ERROR_OK) {
+ retval = swd_run_inner(dap);
+ if (retval == ERROR_OK)
break;
}
alive_sleep(1);
+ dap->switch_through_dormant = !dap->switch_through_dormant;
} while (timeval_ms() < timeout);
- if (status != ERROR_OK) {
+ dap->select = DP_SELECT_INVALID;
+
+ if (retval != ERROR_OK) {
LOG_ERROR("Error connecting DP: cannot read IDR");
- return status;
+ return retval;
}
- LOG_INFO("SWD DPIDR %#8.8" PRIx32, dpidr);
+ LOG_INFO("SWD DPIDR 0x%08" PRIx32, dpidr);
do {
dap->do_reconnect = false;
/* force clear all sticky faults */
swd_clear_sticky_errors(dap);
- status = swd_run_inner(dap);
- if (status != ERROR_WAIT)
+ retval = swd_run_inner(dap);
+ if (retval != ERROR_WAIT)
break;
alive_sleep(10);
} while (timeval_ms() < timeout);
+ return retval;
+}
+
+static int swd_connect(struct adiv5_dap *dap)
+{
+ int status;
+
+ /* FIXME validate transport config ... is the
+ * configured DAP present (check IDCODE)?
+ */
+
+ /* Check if we should reset srst already when connecting, but not if reconnecting. */
+ if (!dap->do_reconnect) {
+ enum reset_types jtag_reset_config = jtag_get_reset_config();
+
+ if (jtag_reset_config & RESET_CNCT_UNDER_SRST) {
+ if (jtag_reset_config & RESET_SRST_NO_GATING)
+ adapter_assert_reset();
+ else
+ LOG_WARNING("\'srst_nogate\' reset_config option is required");
+ }
+ }
+
+ if (dap_is_multidrop(dap))
+ status = swd_connect_multidrop(dap);
+ else
+ status = swd_connect_single(dap);
+
/* IHI 0031E B4.3.2:
* "A WAIT response must not be issued to the ...
* ... writes to the ABORT register"
dap->do_reconnect = false;
- swd->write_reg(swd_cmd(false, false, DP_ABORT),
- DAPABORT | STKCMPCLR | STKERRCLR | WDERRCLR | ORUNERRCLR, 0);
- status = swd_run_inner(dap);
+ status = swd_queue_dp_write_inner(dap, DP_ABORT,
+ DAPABORT | STKCMPCLR | STKERRCLR | WDERRCLR | ORUNERRCLR);
+
+ if (status == ERROR_OK)
+ status = swd_run_inner(dap);
}
if (status == ERROR_OK)
return status;
}
-static int swd_send_sequence(struct adiv5_dap *dap, enum swd_special_seq seq)
-{
- const struct swd_driver *swd = adiv5_dap_swd_driver(dap);
- assert(swd);
-
- return swd->switch_seq(seq);
-}
-
-static inline int check_sync(struct adiv5_dap *dap)
-{
- return do_sync ? swd_run_inner(dap) : ERROR_OK;
-}
-
static int swd_check_reconnect(struct adiv5_dap *dap)
{
if (dap->do_reconnect)
const struct swd_driver *swd = adiv5_dap_swd_driver(dap);
assert(swd);
- swd->write_reg(swd_cmd(false, false, DP_ABORT),
- DAPABORT | STKCMPCLR | STKERRCLR | WDERRCLR | ORUNERRCLR, 0);
- return check_sync(dap);
-}
-
-/** Select the DP register bank matching bits 7:4 of reg. */
-static int swd_queue_dp_bankselect(struct adiv5_dap *dap, unsigned reg)
-{
- /* Only register address 4 is banked. */
- if ((reg & 0xf) != 4)
- return ERROR_OK;
-
- uint32_t select_dp_bank = (reg & 0x000000F0) >> 4;
- uint32_t sel = select_dp_bank
- | (dap->select & (DP_SELECT_APSEL | DP_SELECT_APBANK));
-
- if (sel == dap->select)
- return ERROR_OK;
-
- dap->select = sel;
-
- int retval = swd_queue_dp_write(dap, DP_SELECT, sel);
+ /* TODO: Send DAPABORT in swd_multidrop_select_inner()
+ * in the case the multidrop dap is not selected?
+ * swd_queue_ap_abort() is not currently used anyway...
+ */
+ int retval = swd_multidrop_select(dap);
if (retval != ERROR_OK)
- dap->select = DP_SELECT_INVALID;
+ return retval;
- return retval;
+ swd->write_reg(swd_cmd(false, false, DP_ABORT),
+ DAPABORT | STKCMPCLR | STKERRCLR | WDERRCLR | ORUNERRCLR, 0);
+ return check_sync(dap);
}
static int swd_queue_dp_read(struct adiv5_dap *dap, unsigned reg,
uint32_t *data)
{
- const struct swd_driver *swd = adiv5_dap_swd_driver(dap);
- assert(swd);
-
int retval = swd_check_reconnect(dap);
if (retval != ERROR_OK)
return retval;
- retval = swd_queue_dp_bankselect(dap, reg);
+ retval = swd_multidrop_select(dap);
if (retval != ERROR_OK)
return retval;
- swd->read_reg(swd_cmd(true, false, reg), data, 0);
-
- return check_sync(dap);
+ return swd_queue_dp_read_inner(dap, reg, data);
}
static int swd_queue_dp_write(struct adiv5_dap *dap, unsigned reg,
if (retval != ERROR_OK)
return retval;
- swd_finish_read(dap);
- if (reg == DP_SELECT) {
- dap->select = data & (DP_SELECT_APSEL | DP_SELECT_APBANK | DP_SELECT_DPBANK);
-
- swd->write_reg(swd_cmd(false, false, reg), data, 0);
-
- retval = check_sync(dap);
- if (retval != ERROR_OK)
- dap->select = DP_SELECT_INVALID;
-
- return retval;
- }
-
- retval = swd_queue_dp_bankselect(dap, reg);
+ retval = swd_multidrop_select(dap);
if (retval != ERROR_OK)
return retval;
- swd->write_reg(swd_cmd(false, false, reg), data, 0);
-
- return check_sync(dap);
+ return swd_queue_dp_write_inner(dap, reg, data);
}
/** Select the AP register bank matching bits 7:4 of reg. */
static int swd_queue_ap_bankselect(struct adiv5_ap *ap, unsigned reg)
{
+ int retval;
struct adiv5_dap *dap = ap->dap;
- uint32_t sel = ((uint32_t)ap->ap_num << 24)
- | (reg & 0x000000F0)
- | (dap->select & DP_SELECT_DPBANK);
+ uint64_t sel;
+
+ if (is_adiv6(dap)) {
+ sel = ap->ap_num | (reg & 0x00000FF0);
+ if (sel == (dap->select & ~0xfULL))
+ return ERROR_OK;
+
+ if (dap->select != DP_SELECT_INVALID)
+ sel |= dap->select & 0xf;
+ dap->select = sel;
+ LOG_DEBUG("AP BANKSEL: %" PRIx64, sel);
+
+ retval = swd_queue_dp_write(dap, DP_SELECT, (uint32_t)sel);
+
+ if (retval == ERROR_OK && dap->asize > 32)
+ retval = swd_queue_dp_write(dap, DP_SELECT1, (uint32_t)(sel >> 32));
+
+ if (retval != ERROR_OK)
+ dap->select = DP_SELECT_INVALID;
+
+ return retval;
+ }
+
+ /* ADIv5 */
+ sel = (ap->ap_num << 24) | (reg & ADIV5_DP_SELECT_APBANK);
+ if (dap->select != DP_SELECT_INVALID)
+ sel |= dap->select & DP_SELECT_DPBANK;
if (sel == dap->select)
return ERROR_OK;
dap->select = sel;
- int retval = swd_queue_dp_write(dap, DP_SELECT, sel);
+ retval = swd_queue_dp_write_inner(dap, DP_SELECT, sel);
if (retval != ERROR_OK)
dap->select = DP_SELECT_INVALID;
if (retval != ERROR_OK)
return retval;
+ retval = swd_multidrop_select(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
retval = swd_queue_ap_bankselect(ap, reg);
if (retval != ERROR_OK)
return retval;
if (retval != ERROR_OK)
return retval;
+ retval = swd_multidrop_select(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
swd_finish_read(dap);
+
retval = swd_queue_ap_bankselect(ap, reg);
if (retval != ERROR_OK)
return retval;
/** Executes all queued DAP operations. */
static int swd_run(struct adiv5_dap *dap)
{
+ int retval = swd_multidrop_select(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
swd_finish_read(dap);
+
return swd_run_inner(dap);
}
static void swd_quit(struct adiv5_dap *dap)
{
const struct swd_driver *swd = adiv5_dap_swd_driver(dap);
+ static bool done;
+
+ /* There is no difference if the sequence is sent at the last
+ * or the first swd_quit() call, send it just once */
+ if (done)
+ return;
+
+ done = true;
+ if (dap_is_multidrop(dap)) {
+ swd->switch_seq(SWD_TO_DORMANT);
+ /* Revisit!
+ * Leaving DPs in dormant state was tested and offers some safety
+ * against DPs mismatch in case of unintentional use of non-multidrop SWD.
+ * To put SWJ-DPs to power-on state issue
+ * swd->switch_seq(DORMANT_TO_JTAG);
+ */
+ } else {
+ if (dap->switch_through_dormant) {
+ swd->switch_seq(SWD_TO_DORMANT);
+ swd->switch_seq(DORMANT_TO_JTAG);
+ } else {
+ swd->switch_seq(SWD_TO_JTAG);
+ }
+ }
- swd->switch_seq(SWD_TO_JTAG);
- /* flush the queue before exit */
+ /* flush the queue to shift out the sequence before exit */
swd->run();
}
* REVISIT can we verify "just one SWD DAP" here/early?
*/
.name = "newdap",
- .jim_handler = jim_jtag_newtap,
+ .handler = handle_jtag_newtap,
.mode = COMMAND_CONFIG,
- .help = "declare a new SWD DAP"
+ .help = "declare a new SWD DAP",
+ .usage = "basename dap_type ['-irlen' count] "
+ "['-enable'|'-disable'] "
+ "['-expected_id' number] "
+ "['-ignore-version'] "
+ "['-ignore-bypass'] "
+ "['-ircapture' number] "
+ "['-mask' number]",
},
COMMAND_REGISTRATION_DONE
};