The @code{init_boards} procedure is a similar concept concerning board config files
(@xref{theinitboardprocedure,,The init_board procedure}.)
+@anchor{theinittargeteventsprocedure}
+@subsection The init_target_events procedure
+@cindex init_target_events procedure
+
+A special procedure called @code{init_target_events} is run just after
+@code{init_targets} (@xref{theinittargetsprocedure,,The init_targets
+procedure}.) and before @code{init_board}
+(@xref{theinitboardprocedure,,The init_board procedure}.) It is used
+to set up default target events for the targets that do not have those
+events already assigned.
+
@subsection ARM Core Specific Hacks
If the chip has a DCC, enable it. If the chip is an ARM9 with some
and initially asserted reset signals.
@end deffn
-@deffn {Config Command} {ftdi_layout_signal} name [@option{-data}|@option{-ndata} data_mask] [@option{-oe}|@option{-noe} oe_mask]
+@deffn {Config Command} {ftdi_layout_signal} name [@option{-data}|@option{-ndata} data_mask] [@option{-oe}|@option{-noe} oe_mask] [@option{-alias}|@option{-nalias} name]
Creates a signal with the specified @var{name}, controlled by one or more FTDI
GPIO pins via a range of possible buffer connections. The masks are FTDI GPIO
register bitmasks to tell the driver the connection and type of the output
input as necessary to provide the full set of low, high and Hi-Z
characteristics. In all other cases, the pins specified in a signal definition
are always driven by the FTDI.
+
+If @option{-alias} or @option{-nalias} is used, the signal is created
+identical (or with data inverted) to an already specified signal
+@var{name}.
@end deffn
@deffn {Command} {ftdi_set_signal} name @option{0}|@option{1}|@option{z}
@item @b{gdb-end}
@* When the target has halted and GDB is not doing anything (see early halt)
@item @b{gdb-flash-erase-start}
-@* Before the GDB flash process tries to erase the flash
+@* Before the GDB flash process tries to erase the flash (default is
+@code{reset init})
@item @b{gdb-flash-erase-end}
@* After the GDB flash process has finished erasing the flash
@item @b{gdb-flash-write-start}
@* Before GDB writes to the flash
@item @b{gdb-flash-write-end}
-@* After GDB writes to the flash
+@* After GDB writes to the flash (default is @code{reset halt})
@item @b{gdb-start}
@* Before the target steps, gdb is trying to start/resume the target
@item @b{halted}
@end deffn
@deffn {Flash Driver} lpc2000
-Most members of the LPC1700, LPC1800, LPC2000 and LPC4300 microcontroller
-families from NXP include internal flash and use Cortex-M3 (LPC1700, LPC1800),
-Cortex-M4 (LPC4300) or ARM7TDMI (LPC2000) cores.
+All members of the LPC11(x)00 and LPC1300 microcontroller families and most members
+of the LPC1700, LPC1800, LPC2000 and LPC4300 microcontroller families from NXP
+include internal flash and use Cortex-M0 (LPC11(x)00), Cortex-M3 (LPC1300, LPC1700,
+LPC1800), Cortex-M4 (LPC4300) or ARM7TDMI (LPC2000) cores.
@quotation Note
There are LPC2000 devices which are not supported by the @var{lpc2000}
@option{lpc2000_v1} (older LPC21xx and LPC22xx)
@option{lpc2000_v2} (LPC213x, LPC214x, LPC210[123], LPC23xx and LPC24xx)
@option{lpc1700} (LPC175x and LPC176x)
-or @option{lpc4300} - available also as @option{lpc1800} alias (LPC18x[2357] and
+@option{lpc4300} - available also as @option{lpc1800} alias (LPC18x[2357] and
LPC43x[2357])
+@option{lpc1100} (LPC11(x)xx and LPC13xx)
+or @option{auto} - automatically detects flash variant and size for LPC11(x)00,
+LPC1300 and LPC1700
@item @var{clock_kHz} ... the frequency, in kiloHertz,
at which the core is running
@item @option{calc_checksum} ... optional (but you probably want to provide this!),
@section Misc Commands
@cindex profiling
-@deffn Command {profile} seconds filename
+@deffn Command {profile} seconds filename [start end]
Profiling samples the CPU's program counter as quickly as possible,
which is useful for non-intrusive stochastic profiling.
-Saves up to 10000 sampines in @file{filename} using ``gmon.out'' format.
+Saves up to 10000 samples in @file{filename} using ``gmon.out''
+format. Optional @option{start} and @option{end} parameters allow to
+limit the address range.
@end deffn
@deffn Command {version}