MIPS: update arch_info access to match other targets

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 285603a9588e1c88d6b97d2720c111a6e97dde0e..47951c6d777393d1dd396bbb007a393d48765c2e 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -223,7 +223,7 @@ communication between developers:
 @uref{https://lists.berlios.de/mailman/listinfo/openocd-development}
 
 Discuss and submit patches to this list.
-The @file{PATCHES} file contains basic information about how
+The @file{PATCHES.txt} file contains basic information about how
 to prepare patches.
 
 
@@ -1721,17 +1721,17 @@ In such cases, just specify the relevant port number as zero.
 If you disable all access through TCP/IP, you will need to
 use the command line @option{-pipe} option.
 
-@deffn {Command} gdb_port (number)
+@deffn {Command} gdb_port [number]
 @cindex GDB server
 Specify or query the first port used for incoming GDB connections.
 The GDB port for the
 first target will be gdb_port, the second target will listen on gdb_port + 1, and so on.
 When not specified during the configuration stage,
 the port @var{number} defaults to 3333.
-When specified as zero, this port is not activated.
+When specified as zero, GDB remote access ports are not activated.
 @end deffn
 
-@deffn {Command} tcl_port (number)
+@deffn {Command} tcl_port [number]
 Specify or query the port used for a simplified RPC
 connection that can be used by clients to issue TCL commands and get the
 output from the Tcl engine.
@@ -1741,7 +1741,7 @@ the port @var{number} defaults to 6666.
 When specified as zero, this port is not activated.
 @end deffn
 
-@deffn {Command} telnet_port (number)
+@deffn {Command} telnet_port [number]
 Specify or query the
 port on which to listen for incoming telnet connections.
 This port is intended for interaction with one human through TCL commands.
@@ -4673,7 +4673,7 @@ NAND chips must be declared in configuration scripts,
 plus some additional configuration that's done after
 OpenOCD has initialized.
 
-@deffn {Config Command} {nand device} name controller target [configparams...]
+@deffn {Config Command} {nand device} name driver target [configparams...]
 Declares a NAND device, which can be read and written to
 after it has been configured through @command{nand probe}.
 In OpenOCD, devices are single chips; this is unlike some
@@ -4688,8 +4688,8 @@ configuration files, not interactively.
 
 @itemize @bullet
 @item @var{name} ... may be used to reference the NAND bank
-in other commands.
-@item @var{controller} ... identifies the controller driver
+in most other NAND commands.  A number is also available.
+@item @var{driver} ... identifies the NAND controller driver
 associated with the NAND device being declared.
 @xref{NAND Driver List}.
 @item @var{target} ... names the target used when issuing
@@ -6030,6 +6030,10 @@ and ARM9 commands.
 @deffn Command {arm966e cp15} regnum [value]
 Display cp15 register @var{regnum};
 else if a @var{value} is provided, that value is written to that register.
+The six bit @var{regnum} values are bits 37..32 from table 7-2 of the
+ARM966E-S TRM.
+There is no current control over bits 31..30 from that table,
+as required for BIST support.
 @end deffn
 
 @subsection XScale specific commands