doc/openocd: Fix buspirate example

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 5aab4ba1df0b6adde60c6b53ec3aa81a218209ae..3e5e4cba71fb75256d05147103e3a842fb1707a6 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -3339,21 +3339,21 @@ It uses a simple data protocol over a serial port connection.
 Most hardware development boards have a UART, a real serial port, or a virtual USB serial device, so this driver
 allows you to start building your own JTAG adapter without the complexity of a custom USB connection.
 
-@deffn {Config Command} {buspirate_port} serial_port
+@deffn {Config Command} {buspirate port} serial_port
 Specify the serial port's filename. For example:
 @example
-buspirate_port /dev/ttyUSB0
+buspirate port /dev/ttyUSB0
 @end example
 @end deffn
 
-@deffn {Config Command} {buspirate_speed} (normal|fast)
+@deffn {Config Command} {buspirate speed} (normal|fast)
 Set the communication speed to 115k (normal) or 1M (fast). For example:
 @example
-buspirate_mode normal
+buspirate speed normal
 @end example
 @end deffn
 
-@deffn {Config Command} {buspirate_mode} (normal|open-drain)
+@deffn {Config Command} {buspirate mode} (normal|open-drain)
 Set the Bus Pirate output mode.
 @itemize @minus
 @item In normal mode (push/pull), do not enable the pull-ups, and do not connect I/O header pin VPU to JTAG VREF.
@@ -3361,33 +3361,33 @@ Set the Bus Pirate output mode.
 @end itemize
 For example:
 @example
-buspirate_mode normal
+buspirate mode normal
 @end example
 @end deffn
 
-@deffn {Config Command} {buspirate_pullup} (0|1)
+@deffn {Config Command} {buspirate pullup} (0|1)
 Whether to connect (1) or not (0) the I/O header pin VPU (JTAG VREF)
 to the pull-up/pull-down resistors on MOSI (JTAG TDI), CLK (JTAG TCK), MISO (JTAG TDO) and CS (JTAG TMS).
 For example:
 @example
-buspirate_pullup 0
+buspirate pullup 0
 @end example
 @end deffn
 
-@deffn {Config Command} {buspirate_vreg} (0|1)
+@deffn {Config Command} {buspirate vreg} (0|1)
 Whether to enable (1) or disable (0) the built-in voltage regulator,
 which can be used to supply power to a test circuit through
 I/O header pins +3V3 and +5V. For example:
 @example
-buspirate_vreg 0
+buspirate vreg 0
 @end example
 @end deffn
 
-@deffn {Command} {buspirate_led} (0|1)
+@deffn {Command} {buspirate led} (0|1)
 Turns the Bus Pirate's LED on (1) or off (0). For example:
 @end deffn
 @example
-buspirate_led 1
+buspirate led 1
 @end example
 
 @end deffn