+@deffn {Flash Driver} mdr
+This drivers handles the integrated NOR flash on Milandr Cortex-M
+based controllers. A known limitation is that the Info memory can't be
+read or verified as it's not memory mapped.
+
+@example
+flash bank <name> mdr <base> <size> \
+ 0 0 <target#> @var{type} @var{page_count} @var{sec_count}
+@end example
+
+@itemize @bullet
+@item @var{type} - 0 for main memory, 1 for info memory
+@item @var{page_count} - total number of pages
+@item @var{sec_count} - number of sector per page count
+@end itemize
+
+Example usage:
+@example
+if @{ [info exists IMEMORY] && [string equal $IMEMORY true] @} @{
+ flash bank $@{_CHIPNAME@}_info.flash mdr 0x00000000 0x01000 \
+ 0 0 $_TARGETNAME 1 1 4
+@} else @{
+ flash bank $_CHIPNAME.flash mdr 0x00000000 0x20000 \
+ 0 0 $_TARGETNAME 0 32 4
+@}
+@end example
+@end deffn
+
+@deffn {Flash Driver} niietcm4
+This drivers handles the integrated NOR flash on NIIET Cortex-M4
+based controllers. Flash size and sector layout are auto-configured by the driver.
+Main flash memory is called "Bootflash" and has main region and info region.
+Info region is NOT memory mapped by default,
+but it can replace first part of main region if needed.
+Full erase, single and block writes are supported for both main and info regions.
+There is additional not memory mapped flash called "Userflash", which
+also have division into regions: main and info.
+Purpose of userflash - to store system and user settings.
+Driver has special commands to perform operations with this memmory.
+
+@example
+flash bank $_FLASHNAME niietcm4 0 0 0 0 $_TARGETNAME
+@end example
+
+Some niietcm4-specific commands are defined:
+
+@deffn Command {niietcm4 uflash_read_byte} bank ('main'|'info') address
+Read byte from main or info userflash region.
+@end deffn
+
+@deffn Command {niietcm4 uflash_write_byte} bank ('main'|'info') address value
+Write byte to main or info userflash region.
+@end deffn
+
+@deffn Command {niietcm4 uflash_full_erase} bank
+Erase all userflash including info region.
+@end deffn
+
+@deffn Command {niietcm4 uflash_erase} bank ('main'|'info') first_sector last_sector
+Erase sectors of main or info userflash region, starting at sector first up to and including last.
+@end deffn
+
+@deffn Command {niietcm4 uflash_protect_check} bank ('main'|'info')
+Check sectors protect.
+@end deffn
+
+@deffn Command {niietcm4 uflash_protect} bank ('main'|'info') first_sector last_sector ('on'|'off')
+Protect sectors of main or info userflash region, starting at sector first up to and including last.
+@end deffn
+
+@deffn Command {niietcm4 bflash_info_remap} bank ('on'|'off')
+Enable remapping bootflash info region to 0x00000000 (or 0x40000000 if external memory boot used).
+@end deffn
+
+@deffn Command {niietcm4 extmem_cfg} bank ('gpioa'|'gpiob'|'gpioc'|'gpiod'|'gpioe'|'gpiof'|'gpiog'|'gpioh') pin_num ('func1'|'func3')
+Configure external memory interface for boot.
+@end deffn
+
+@deffn Command {niietcm4 service_mode_erase} bank
+Perform emergency erase of all flash (bootflash and userflash).
+@end deffn
+
+@deffn Command {niietcm4 driver_info} bank
+Show information about flash driver.
+@end deffn
+
+@end deffn
+
+@deffn {Flash Driver} nrf51
+All members of the nRF51 microcontroller families from Nordic Semiconductor
+include internal flash and use ARM Cortex-M0 core.
+
+@example
+flash bank $_FLASHNAME nrf51 0 0x00000000 0 0 $_TARGETNAME
+@end example
+
+Some nrf51-specific commands are defined:
+
+@deffn Command {nrf51 mass_erase}
+Erases the contents of the code memory and user information
+configuration registers as well. It must be noted that this command
+works only for chips that do not have factory pre-programmed region 0
+code.
+@end deffn
+
+@end deffn
+