From 900d745567809d9f0163cfde5832b10ec0581a0e Mon Sep 17 00:00:00 2001 From: Dean Glazeski Date: Wed, 9 Dec 2009 12:51:52 -0600 Subject: [PATCH] Olimex SAM9-L9260 board configuration update. This updates the board configuration for the SAM9-L9260 board with the configuration for the on-board NAND and dataflash. Included are commands for configuring the AT91SAM9 NAND flash driver. Signed-off-by: David Brownell --- tcl/board/olimex_sam9_l9260.cfg | 52 +++++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+) diff --git a/tcl/board/olimex_sam9_l9260.cfg b/tcl/board/olimex_sam9_l9260.cfg index 5c4714e199..7c4b2ccb0a 100644 --- a/tcl/board/olimex_sam9_l9260.cfg +++ b/tcl/board/olimex_sam9_l9260.cfg @@ -35,6 +35,7 @@ $_TARGETNAME configure -event reset-init { ## # Clock configuration for 99.328 MHz main clock. ## + puts "Setting up clock" mww 0xfffffc20 0x00004001 # CKGR_MOR : enable main oscillator, 512 slow clock startup sleep 20 # wait 20 ms (need 15.6 ms for startup) mww 0xfffffc30 0x00000001 # PMC_MCKR : switch to main oscillator (18.432 MHz) @@ -53,6 +54,7 @@ $_TARGETNAME configure -event reset-init { ## # SDRAM configuration for 2 x Samsung K4S561632J-UC75, 4M x 16Bit x 4 Banks. ## + puts "Configuring SDRAM" mww 0xfffff870 0xffff0000 # PIOC_ASR : select peripheral function for D15..D31 mww 0xfffff804 0xffff0000 # PIOC_PDR : disable PIO function for D15..D31 @@ -86,4 +88,54 @@ $_TARGETNAME configure -event reset-init { mww 0x20000000 0 mww 0xffffea04 0x2b6 # SDRAMC_TR : set refresh timer count to 7 us + + ## + # NAND Flash Configuration for 1 x Samsung K9F4G08U0M, 512M x 8Bit. + ## + puts "Configuring NAND flash" + mww 0xfffffc10 0x00000010 ;# PMC_PCER : enable PIOC clock + mww 0xfffff800 0x00006000 ;# PIOC_PER : enable PIO function for 13(RDY/~BSY) and 14(~CS) + mww 0xfffff810 0x00004000 ;# PIOC_OER : enable output on 14 + mww 0xfffff814 0x00002000 ;# PIOC_ODR : disable output on 13 + mww 0xfffff830 0x00004000 ;# PIOC_SODR : set 14 to disable NAND + mww 0xfffff864 0x00002000 ;# PIOC_PUER : enable pull-up on 13 + + mww 0xffffef1c 0x0001000A ;# EBI_CSA : assign EBI CS3 to NAND, same settings as before + + mww 0xffffec30 0x00010001 ;# SMC_SETUP3 : 1 clock cycle setup for NRD and NWE + mww 0xffffec34 0x03030303 ;# SMC_PULSE3 : 3 clock cycle pulse for all signals + mww 0xffffec38 0x00050005 ;# SMC_CYCLE3 : 5 clock cycle NRD and NWE cycle + mww 0xffffec3C 0x00020003 ;# SMC_MODE3 : NRD and NWE control, no NWAIT, 8-bit DBW, + # 3 TDF cycles, no optimization + + mww 0xffffe800 0x00000001 ;# ECC_CR : reset the ECC parity registers + mww 0xffffe804 0x00000002 ;# ECC_MR : page size is 2112 words (word is 8 bits) + + nand probe at91sam9260.flash + + ## + # Dataflash configuration for 1 x Atmel AT45DB161D, 16Mbit + ## + puts "Setting up dataflash" + mww 0xfffff404 0x00000807 ;# PIOA_PDR : disable PIO function for 0(SPI0_MISO), 1(SPI0_MOSI), + # 2(SPI0_SPCK), and 11(SPI0_NPCS1) + mww 0xfffff470 0x00000007 ;# PIOA_ASR : select peripheral A function for 0, 1, and 2 + mww 0xfffff474 0x00000800 ;# PIOA_BSR : select peripheral B function for 11 + mww 0xfffffc10 0x00001000 ;# PMC_PCER : enable SPI0 clock + + mww 0xfffc8000 0x00000080 ;# SPI0_CR : software reset SPI0 + mww 0xfffc8000 0x00000080 ;# SPI0_CR : again to be sure + mww 0xfffc8004 0x000F0011 ;# SPI0_MR : master mode with nothing selected + + mww 0xfffc8034 0x011a0302 ;# SPI0_CSR1 : capture on leading edge, 8-bits/tx. 33MHz baud, + # 250ns delay before SPCK, 250ns b/n tx + + mww 0xfffc8004 0x000D0011 ;# SPI0_MR : same config, select NPCS1 + mww 0xfffc8000 0x00000001 ;# SPI0_CR : enable SPI0 } + +nand device at91sam9260.flash at91sam9 at91sam9260.cpu 0x40000000 0xffffe800 +at91sam9 cle 0 22 +at91sam9 ale 0 21 +at91sam9 rdy_busy 0 0xfffff800 13 +at91sam9 ce 0 0xfffff800 14 -- 2.30.2