unsik Kim <donari75@gmail.com>:
authorzwelch <zwelch@b42882b7-edfa-0310-969c-e2dbd0fdcd60>
Wed, 27 May 2009 12:30:42 +0000 (12:30 +0000)
committerzwelch <zwelch@b42882b7-edfa-0310-969c-e2dbd0fdcd60>
Wed, 27 May 2009 12:30:42 +0000 (12:30 +0000)
Add mflash configuration code, updating relevant documentation.

git-svn-id: svn://svn.berlios.de/openocd/trunk@1930 b42882b7-edfa-0310-969c-e2dbd0fdcd60

doc/openocd.texi
src/flash/mflash.c
src/flash/mflash.h

index 78d53c582a0a55f89325f47371371687f563128c..00f9acf00944846d5c8761b9be08ab1ebb786dc0 100644 (file)
@@ -2393,15 +2393,29 @@ if the @option{erase} parameter is given.
 @itemize @bullet
 @item @b{mflash probe} 
 @cindex mflash probe
-Probe mflash.
+@*Probe mflash.
 @item @b{mflash write} <@var{num}> <@var{file}> <@var{offset}>
 @cindex mflash write
-Write the binary <@var{file}> to mflash bank <@var{num}>, starting at
+@*Write the binary <@var{file}> to mflash bank <@var{num}>, starting at
 <@var{offset}> bytes from the beginning of the bank.
 @item @b{mflash dump} <@var{num}> <@var{file}> <@var{offset}> <@var{size}>
 @cindex mflash dump
-Dump <size> bytes, starting at <@var{offset}> bytes from the beginning of the <@var{num}> bank 
+@*Dump <size> bytes, starting at <@var{offset}> bytes from the beginning of the <@var{num}> bank 
 to a <@var{file}>.
+@item @b{mflash config pll} <@var{frequency}>
+@cindex mflash config pll
+@*Configure mflash pll. <@var{frequency}> is input frequency of mflash. The order is Hz.
+Issuing this command will erase mflash's whole internal nand and write new pll. 
+After this command, mflash needs power-on-reset for normal operation.
+If pll was newly configured, storage and boot(optional) info also need to be update.
+@item @b{mflash config boot}
+@cindex mflash config boot
+@*Configure bootable option. If bootable option is set, mflash offer the first 8 sectors
+(4kB) for boot.
+@item @b{mflash config storage}
+@cindex mflash config storage
+@*Configure storage information. For the normal storage operation, this information must be
+written. 
 @end itemize
 
 @section flash bank command
index 29f562b1d9f5ffdd3d2d4ee56d602d587729e924..b5c7d46ba912171649bec9ef59eec0b88005d231 100644 (file)
@@ -356,12 +356,10 @@ static int mg_dsk_drv_info(void)
        return ERROR_OK;
 }
 
-static int mg_mflash_probe(void)
+static int mg_mflash_rst(void)
 {
        mg_init_gpio();
 
-       LOG_INFO("reset mflash");
-
        mg_hdrst(0);
 
        if (mg_dsk_wait(mg_io_wait_bsy, MG_OEM_DISK_WAIT_TIME_LONG) != ERROR_OK)
@@ -382,6 +380,16 @@ static int mg_mflash_probe(void)
        if (mg_dsk_wait(mg_io_wait_not_bsy, MG_OEM_DISK_WAIT_TIME_LONG) != ERROR_OK)
                return ERROR_FAIL;
 
+       LOG_INFO("mflash: reset ok");
+
+       return ERROR_OK;
+}
+
+static int mg_mflash_probe(void)
+{
+       if (mg_mflash_rst() != ERROR_OK)
+               return ERROR_FAIL;
+
        if (mg_dsk_drv_info() != ERROR_OK)
                return ERROR_FAIL;
 
@@ -465,7 +473,8 @@ static int mg_mflash_read_sects(void *buff, u32 sect_num, u32 sect_cnt)
        return ERROR_OK;
 }
 
-static int mg_mflash_do_write_sects(void *buff, u32 sect_num, u32 sect_cnt)
+static int mg_mflash_do_write_sects(void *buff, u32 sect_num, u32 sect_cnt,
+               mg_io_type_cmd cmd)
 {
        u32 i, address;
        int ret;
@@ -473,10 +482,8 @@ static int mg_mflash_do_write_sects(void *buff, u32 sect_num, u32 sect_cnt)
        u8 *buff_ptr = buff;
        duration_t duration;
 
-       if ( mg_dsk_io_cmd(sect_num, sect_cnt, mg_io_cmd_write) != ERROR_OK ) {
-               LOG_ERROR("mg_io_cmd_write fail");
+       if ( mg_dsk_io_cmd(sect_num, sect_cnt, cmd) != ERROR_OK )
                return ERROR_FAIL;
-       }
 
        address = mflash_bank->base + MG_BUFFER_OFFSET;
 
@@ -506,7 +513,10 @@ static int mg_mflash_do_write_sects(void *buff, u32 sect_num, u32 sect_cnt)
                }
        }
 
-       ret = mg_dsk_wait(mg_io_wait_rdy, MG_OEM_DISK_WAIT_TIME_NORMAL);
+       if (cmd == mg_io_cmd_write)
+               ret = mg_dsk_wait(mg_io_wait_rdy, MG_OEM_DISK_WAIT_TIME_NORMAL);
+       else
+               ret = mg_dsk_wait(mg_io_wait_rdy, MG_OEM_DISK_WAIT_TIME_LONG);
 
        return ret;
 }
@@ -522,7 +532,7 @@ static int mg_mflash_write_sects(void *buff, u32 sect_num, u32 sect_cnt)
        for (i = 0; i < quotient; i++) {
                LOG_DEBUG("sect num : %u buff : %0lx", sect_num, 
                        (unsigned long)buff_ptr);
-               mg_mflash_do_write_sects(buff_ptr, sect_num, 256);
+               mg_mflash_do_write_sects(buff_ptr, sect_num, 256, mg_io_cmd_write);
                sect_num += 256;
                buff_ptr += 256 * MG_MFLASH_SECTOR_SIZE;
        }
@@ -530,7 +540,7 @@ static int mg_mflash_write_sects(void *buff, u32 sect_num, u32 sect_cnt)
        if (residue) {
                LOG_DEBUG("sect num : %u buff : %0lx", sect_num, 
                        (unsigned long)buff_ptr);
-               mg_mflash_do_write_sects(buff_ptr, sect_num, residue);
+               mg_mflash_do_write_sects(buff_ptr, sect_num, residue, mg_io_cmd_write);
        }
 
        return ERROR_OK;
@@ -749,6 +759,433 @@ static int mg_dump_cmd(struct command_context_s *cmd_ctx, char *cmd, char **args
        return ERROR_OK;
 }
 
+
+static int mg_set_feature(mg_feature_id feature, mg_feature_val config)
+{
+       target_t *target = mflash_bank->target;
+       u32 mg_task_reg = mflash_bank->base + MG_REG_OFFSET;
+
+       if (mg_dsk_wait(mg_io_wait_rdy_noerr, MG_OEM_DISK_WAIT_TIME_NORMAL)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       target_write_u8(target, mg_task_reg + MG_REG_FEATURE, feature);
+       target_write_u8(target, mg_task_reg + MG_REG_SECT_CNT, config);
+       target_write_u8(target, mg_task_reg + MG_REG_COMMAND,
+                       mg_io_cmd_set_feature);
+
+       return ERROR_OK;
+}
+
+static int mg_is_valid_pll(double XIN, int N, double CLK_OUT, int NO)
+{
+       double v1 = XIN / N;
+       double v2 = CLK_OUT * NO;
+
+       if (v1 <1000000 || v1 > 15000000 || v2 < 100000000 || v2 > 500000000)
+               return ERROR_FAIL;
+
+       return ERROR_OK;
+}
+
+static int mg_pll_get_M(unsigned short feedback_div)
+{
+       int i, M;
+
+       for (i = 1, M=0; i < 512; i <<= 1, feedback_div >>= 1)
+               M += (feedback_div & 1) * i;
+
+       return M + 2;
+}
+
+static int mg_pll_get_N(unsigned char input_div)
+{
+       int i, N;
+
+       for (i = 1, N = 0; i < 32; i <<= 1, input_div >>= 1)
+               N += (input_div & 1) * i;
+
+       return N + 2;
+}
+
+static int mg_pll_get_NO(unsigned char  output_div)
+{
+       int i, NO;
+
+       for (i = 0, NO = 1; i < 2; ++i, output_div >>= 1)
+               if(output_div & 1)
+                       NO = NO << 1;
+
+       return NO;
+}
+
+static double mg_do_calc_pll(double XIN, mg_pll_t * p_pll_val, int is_approximate)
+{
+       unsigned short i;
+       unsigned char  j, k;
+       int            M, N, NO;
+       double CLK_OUT;
+       double DIV = 1;
+       double ROUND = 0;
+
+       if (is_approximate) {
+               DIV   = 1000000;
+               ROUND = 500000;
+       }
+
+       for (i = 0; i < MG_PLL_MAX_FEEDBACKDIV_VAL ; ++i) {
+               M  = mg_pll_get_M(i);
+
+               for (j = 0; j < MG_PLL_MAX_INPUTDIV_VAL ; ++j) {
+                       N  = mg_pll_get_N(j);
+
+                       for (k = 0; k < MG_PLL_MAX_OUTPUTDIV_VAL ; ++k) {
+                               NO = mg_pll_get_NO(k);
+
+                               CLK_OUT = XIN * ((double)M / N) / NO;
+
+                               if ((int)((CLK_OUT+ROUND) / DIV)
+                                               == (int)(MG_PLL_CLK_OUT / DIV)) {
+                                       if (mg_is_valid_pll(XIN, N, CLK_OUT, NO) == ERROR_OK)
+                                       {
+                                               p_pll_val->lock_cyc = (int)(XIN * MG_PLL_STD_LOCKCYCLE / MG_PLL_STD_INPUTCLK);
+                                               p_pll_val->feedback_div = i;
+                                               p_pll_val->input_div = j;
+                                               p_pll_val->output_div = k;
+
+                                               return CLK_OUT;
+                                       }
+                               }
+                       }
+               }
+       }
+
+       return 0;
+}
+
+static double mg_calc_pll(double XIN, mg_pll_t *p_pll_val)
+{
+       double CLK_OUT;
+
+       CLK_OUT = mg_do_calc_pll(XIN, p_pll_val, 0);
+
+       if (!CLK_OUT)
+               return mg_do_calc_pll(XIN, p_pll_val, 1);
+       else
+               return CLK_OUT;
+}
+
+static int mg_verify_interface(void)
+{
+       u16 buff[MG_MFLASH_SECTOR_SIZE >> 1];
+       u16 i, j;
+       u32 address = mflash_bank->base + MG_BUFFER_OFFSET;
+       target_t *target = mflash_bank->target;
+
+       for (j = 0; j < 10; j++) {
+               for (i = 0; i < MG_MFLASH_SECTOR_SIZE >> 1; i++)
+                       buff[i] = i;
+
+               target->type->write_memory(target, address, 2,
+                               MG_MFLASH_SECTOR_SIZE / 2, (u8 *)buff);
+
+               memset(buff, 0xff, MG_MFLASH_SECTOR_SIZE);
+
+               target->type->read_memory(target, address, 2,
+                               MG_MFLASH_SECTOR_SIZE / 2, (u8 *)buff);
+
+               for (i = 0; i < MG_MFLASH_SECTOR_SIZE >> 1; i++) {
+                       if (buff[i] != i) {
+                               LOG_ERROR("mflash: verify interface fail");
+                               return ERROR_FAIL;
+                       }
+               }
+       }
+
+       LOG_INFO("mflash: verify interface ok");
+       return ERROR_OK;
+}
+
+static const char g_strSEG_SerialNum[20] = {
+       'G','m','n','i','-','e','e','S','g','a','e','l',
+       0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20
+};
+
+static const char g_strSEG_FWRev[8] = {
+       'F','X','L','T','2','v','0','.'
+};
+
+static const char g_strSEG_ModelNum[40] = {
+       'F','X','A','L','H','S','2',0x20,'0','0','s','7',
+       0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,
+       0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,
+       0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20
+};
+
+static void mg_gen_ataid(mg_io_type_drv_info *pSegIdDrvInfo)
+{
+       /* b15 is ATA device(0) , b7 is Removable Media Device */
+       pSegIdDrvInfo->general_configuration            = 0x045A;
+       /* 128MB :   Cylinder=> 977 , Heads=> 8 ,  Sectors=> 32
+        * 256MB :   Cylinder=> 980 , Heads=> 16 , Sectors=> 32
+        * 384MB :   Cylinder=> 745 , Heads=> 16 , Sectors=> 63
+        */
+       pSegIdDrvInfo->number_of_cylinders              = 0x02E9;
+       pSegIdDrvInfo->reserved1                        = 0x0;
+       pSegIdDrvInfo->number_of_heads                  = 0x10;
+       pSegIdDrvInfo->unformatted_bytes_per_track      = 0x0;
+       pSegIdDrvInfo->unformatted_bytes_per_sector     = 0x0;
+       pSegIdDrvInfo->sectors_per_track                = 0x3F;
+       pSegIdDrvInfo->vendor_unique1[0]                = 0x000B;
+       pSegIdDrvInfo->vendor_unique1[1]                = 0x7570;
+       pSegIdDrvInfo->vendor_unique1[2]                = 0x8888;
+
+       memcpy(pSegIdDrvInfo->serial_number, (void *)g_strSEG_SerialNum,20);
+       /* 0x2 : dual buffer */
+       pSegIdDrvInfo->buffer_type                      = 0x2;
+       /* buffer size : 2KB */
+       pSegIdDrvInfo->buffer_sector_size               = 0x800;
+       pSegIdDrvInfo->number_of_ecc_bytes              = 0;
+
+       memcpy(pSegIdDrvInfo->firmware_revision, (void *)g_strSEG_FWRev,8);
+
+       memcpy(pSegIdDrvInfo->model_number, (void *)g_strSEG_ModelNum,40);
+
+       pSegIdDrvInfo->maximum_block_transfer           = 0x4;
+       pSegIdDrvInfo->vendor_unique2                   = 0x0;
+       pSegIdDrvInfo->dword_io                         = 0x00;
+       /* b11 : IORDY support(PIO Mode 4), b10 : Disable/Enbale IORDY
+        * b9  : LBA support, b8 : DMA mode support
+        */
+       pSegIdDrvInfo->capabilities                     = 0x1 << 9;
+
+       pSegIdDrvInfo->reserved2                        = 0x4000;
+       pSegIdDrvInfo->vendor_unique3                   = 0x00;
+       /* PIOMode-2 support */
+       pSegIdDrvInfo->pio_cycle_timing_mode            = 0x02;
+       pSegIdDrvInfo->vendor_unique4                   = 0x00;
+       /* MultiWord-2 support */
+       pSegIdDrvInfo->dma_cycle_timing_mode            = 0x00;
+       /* b1 : word64~70 is valid
+        * b0 : word54~58 are valid and reflect the current numofcyls,heads,sectors
+        * b2 : If device supports Ultra DMA , set to one to vaildate word88
+        */
+       pSegIdDrvInfo->translation_fields_valid         = (0x1 << 1) | (0x1 << 0);
+       pSegIdDrvInfo->number_of_current_cylinders      = 0x02E9;
+       pSegIdDrvInfo->number_of_current_heads          = 0x10;
+       pSegIdDrvInfo->current_sectors_per_track        = 0x3F;
+       pSegIdDrvInfo->current_sector_capacity_lo       = 0x7570;
+       pSegIdDrvInfo->current_sector_capacity_hi       = 0x000B;
+
+       pSegIdDrvInfo->multi_sector_count                       = 0x04;
+       /* b8 : Multiple secotr setting valid , b[7:0] num of secotrs per block */
+       pSegIdDrvInfo->multi_sector_setting_valid               = 0x01;
+       pSegIdDrvInfo->total_user_addressable_sectors_lo        = 0x7570;
+       pSegIdDrvInfo->total_user_addressable_sectors_hi        = 0x000B;
+       pSegIdDrvInfo->single_dma_modes_supported               = 0x00;
+       pSegIdDrvInfo->single_dma_transfer_active               = 0x00;
+       /* b2 :Multi-word DMA mode 2, b1 : Multi-word DMA mode 1 */
+       pSegIdDrvInfo->multi_dma_modes_supported                = (0x1 << 0);
+       /* b2 :Multi-word DMA mode 2, b1 : Multi-word DMA mode 1 */
+       pSegIdDrvInfo->multi_dma_transfer_active                = (0x1 << 0);
+       /* b0 : PIO Mode-3 support, b1 : PIO Mode-4 support */
+       pSegIdDrvInfo->adv_pio_mode                             = 0x00;
+       /* 480(0x1E0)nsec for Multi-word DMA mode0
+        * 150(0x96) nsec for Multi-word DMA mode1
+        * 120(0x78) nsec for Multi-word DMA mode2
+        */
+       pSegIdDrvInfo->min_dma_cyc                      = 0x1E0;
+       pSegIdDrvInfo->recommend_dma_cyc                = 0x1E0;
+       pSegIdDrvInfo->min_pio_cyc_no_iordy             = 0x1E0;
+       pSegIdDrvInfo->min_pio_cyc_with_iordy           = 0x1E0;
+       memset((void *)pSegIdDrvInfo->reserved3, 0x00, 22);
+       /* b7 : ATA/ATAPI-7 ,b6 : ATA/ATAPI-6 ,b5 : ATA/ATAPI-5,b4 : ATA/ATAPI-4 */
+       pSegIdDrvInfo->major_ver_num                    = 0x7E;
+       /* 0x1C : ATA/ATAPI-6 T13 1532D revision1 */
+       pSegIdDrvInfo->minor_ver_num                    = 0x19;
+       /* NOP/READ BUFFER/WRITE BUFFER/Power management feature set support */
+       pSegIdDrvInfo->feature_cmd_set_suprt0           = 0x7068;
+       /* Features/command set is valid/Advanced Pwr management/CFA feature set
+        * not support
+        */
+       pSegIdDrvInfo->feature_cmd_set_suprt1           = 0x400C;
+       pSegIdDrvInfo->feature_cmd_set_suprt2           = 0x4000;
+       /* READ/WRITE BUFFER/PWR Management enable */
+       pSegIdDrvInfo->feature_cmd_set_en0              = 0x7000;
+       /* CFA feature is disabled / Advancde power management disable */
+       pSegIdDrvInfo->feature_cmd_set_en1              = 0x0;
+       pSegIdDrvInfo->feature_cmd_set_en2              = 0x4000;
+       pSegIdDrvInfo->reserved4                        = 0x0;
+       /* 0x1 * 2minutes */
+       pSegIdDrvInfo->req_time_for_security_er_done    = 0x19;
+       pSegIdDrvInfo->req_time_for_enhan_security_er_done      = 0x19;
+       /* Advanced power management level 1 */
+       pSegIdDrvInfo->adv_pwr_mgm_lvl_val                      = 0x0;
+       pSegIdDrvInfo->reserved5                        = 0x0;
+       memset((void *)pSegIdDrvInfo->reserved6, 0x00, 68);
+       /* Security mode feature is disabled */
+       pSegIdDrvInfo->security_stas                    = 0x0;
+       memset((void *)pSegIdDrvInfo->vendor_uniq_bytes, 0x00, 62);
+       /* CFA power mode 1 support in maximum 200mA */
+       pSegIdDrvInfo->cfa_pwr_mode                     = 0x0100;
+       memset((void *)pSegIdDrvInfo->reserved7, 0x00, 190);
+}
+
+static int mg_storage_config(void)
+{
+       u8 buff[512];
+
+       if (mg_set_feature(mg_feature_id_transmode, mg_feature_val_trans_vcmd)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       mg_gen_ataid((mg_io_type_drv_info *)buff);
+
+       if (mg_mflash_do_write_sects(buff, 0, 1, mg_vcmd_update_stgdrvinfo)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       if (mg_set_feature(mg_feature_id_transmode, mg_feature_val_trans_default)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       LOG_INFO("mflash: storage config ok");
+       return ERROR_OK;
+}
+
+static int mg_boot_config(void)
+{
+       u8 buff[512];
+
+       if (mg_set_feature(mg_feature_id_transmode, mg_feature_val_trans_vcmd)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       memset(buff, 0xff, 512);
+
+       buff[0] = mg_op_mode_snd;               /* operation mode */
+       buff[1] = MG_UNLOCK_OTP_AREA;
+       buff[2] = 4;                            /* boot size */
+       *((u32 *)(buff + 4)) = 0;               /* XIP size */
+
+       if (mg_mflash_do_write_sects(buff, 0, 1, mg_vcmd_update_xipinfo)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       if (mg_set_feature(mg_feature_id_transmode, mg_feature_val_trans_default)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       LOG_INFO("mflash: boot config ok");
+       return ERROR_OK;
+}
+
+static int mg_set_pll(mg_pll_t *pll)
+{
+       u8 buff[512];
+
+       memset(buff, 0xff, 512);
+       *((u32 *)&buff[0]) = pll->lock_cyc;     /* PLL Lock cycle */
+       *((u16 *)&buff[4]) = pll->feedback_div; /* PLL Feedback 9bit Divider */
+       buff[6] = pll->input_div;               /* PLL Input 5bit Divider */
+       buff[7] = pll->output_div;              /* PLL Output Divider */
+
+       if (mg_set_feature(mg_feature_id_transmode, mg_feature_val_trans_vcmd)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       if (mg_mflash_do_write_sects(buff, 0, 1, mg_vcmd_wr_pll)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       if (mg_set_feature(mg_feature_id_transmode, mg_feature_val_trans_default)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       LOG_INFO("mflash: set pll ok");
+       return ERROR_OK;
+}
+
+static int mg_erase_nand(void)
+{
+       if (mg_set_feature(mg_feature_id_transmode, mg_feature_val_trans_vcmd)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       if (mg_mflash_do_write_sects(NULL, 0, 0, mg_vcmd_purge_nand)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       if (mg_set_feature(mg_feature_id_transmode, mg_feature_val_trans_default)
+                       != ERROR_OK)
+               return ERROR_FAIL;
+
+       LOG_INFO("mflash: erase nand ok");
+       return ERROR_OK;
+}
+
+int mg_config_cmd(struct command_context_s *cmd_ctx, char *cmd,
+               char **args, int argc)
+{
+       double fin, fout;
+       mg_pll_t pll;
+
+       if (mg_verify_interface() != ERROR_OK)
+               return ERROR_FAIL;
+
+       if (mg_mflash_rst() != ERROR_OK)
+               return ERROR_FAIL;
+
+       switch (argc) {
+               case 2:
+                       if (!strcmp(args[1], "boot")) {
+                               if (mg_boot_config() != ERROR_OK)
+                                       return ERROR_FAIL;
+
+                               return ERROR_OK;
+                       } else if (!strcmp(args[1], "storage")) {
+                               if (mg_storage_config() != ERROR_OK)
+                                       return ERROR_FAIL;
+
+                               return ERROR_OK;
+                       } else
+                               return ERROR_COMMAND_NOTFOUND;
+                       break;
+               case 3:
+                       if (!strcmp(args[1], "pll")) {
+                               fin = strtoul(args[2], NULL, 0);
+
+                               if (fin > MG_PLL_CLK_OUT)
+                                       return ERROR_FAIL;
+
+                               fout = mg_calc_pll(fin, &pll);
+
+                               if (!fout)
+                                       return ERROR_FAIL;
+
+                               LOG_INFO("mflash: Fout=%u Hz, feedback=%u," 
+                                               "indiv=%u, outdiv=%u, lock=%u",
+                                               (u32)fout, pll.feedback_div,
+                                               pll.input_div, pll.output_div,
+                                               pll.lock_cyc);
+
+                               if (mg_erase_nand() != ERROR_OK)
+                                       return ERROR_FAIL;
+
+                               if (mg_set_pll(&pll) != ERROR_OK)
+                                       return ERROR_FAIL;
+
+                               return ERROR_OK;
+                       } else
+                               return ERROR_COMMAND_NOTFOUND;
+                       break;
+               default:
+                       return ERROR_COMMAND_SYNTAX_ERROR;
+       }
+
+       return ERROR_OK;
+}
+
 int mflash_init_drivers(struct command_context_s *cmd_ctx)
 {
        if (mflash_bank) {
@@ -757,6 +1194,8 @@ int mflash_init_drivers(struct command_context_s *cmd_ctx)
                                "mflash write <num> <file> <address>");
                register_command(cmd_ctx, mflash_cmd, "dump", mg_dump_cmd, COMMAND_EXEC,
                                                "mflash dump <num> <file> <address> <size>");
+               register_command(cmd_ctx, mflash_cmd, "config", mg_config_cmd,
+                               COMMAND_EXEC, "mflash config <num> <stage>");
        }
 
        return ERROR_OK;
index 3d88ef4c3f6062438fd727e3ae38ba3069f9cefa..da148dcae3c5c405e711bb197d29fdd84fc5722d 100644 (file)
@@ -48,7 +48,7 @@ typedef struct _mg_io_type_drv_info {
        mg_io_uint16 unformatted_bytes_per_track;               /* 04 */
        mg_io_uint16 unformatted_bytes_per_sector;              /* 05 */
        mg_io_uint16 sectors_per_track;                                 /* 06 */
-       mg_io_uint8  vendor_unique1[6];                                 /* 07/08/09 */
+       mg_io_uint16  vendor_unique1[3];                                /* 07/08/09 */
 
        mg_io_uint8  serial_number[20];                                 /* 10~19 */
 
@@ -117,6 +117,14 @@ typedef struct _mg_io_type_drv_info {
 
 } mg_io_type_drv_info;
 
+typedef struct _mg_pll_t
+{
+       unsigned int   lock_cyc;
+       unsigned short feedback_div;    /* 9bit divider */
+       unsigned char  input_div;       /* 5bit divider */
+       unsigned char  output_div;      /* 2bit divider */
+} mg_pll_t;
+
 typedef struct mg_drv_info_s {
        mg_io_type_drv_info drv_id;
        u32 tot_sects;
@@ -158,6 +166,16 @@ extern int mflash_init_drivers(struct command_context_s *cmd_ctx);
 #define MG_OEM_DISK_WAIT_TIME_NORMAL   3000    /* msec */
 #define MG_OEM_DISK_WAIT_TIME_SHORT            1000    /* msec */
 
+#define MG_PLL_CLK_OUT 66000000.0 /* 66Mhz */
+#define MG_PLL_MAX_FEEDBACKDIV_VAL 512
+#define MG_PLL_MAX_INPUTDIV_VAL 32
+#define MG_PLL_MAX_OUTPUTDIV_VAL 4
+
+#define MG_PLL_STD_INPUTCLK 12000000.0 /* 12Mhz */
+#define MG_PLL_STD_LOCKCYCLE 10000
+
+#define MG_UNLOCK_OTP_AREA 0xFF
+
 typedef enum _mg_io_type_wait{
 
        mg_io_wait_bsy       = 1,
@@ -238,4 +256,37 @@ typedef enum _mg_io_type_cmd
 
 } mg_io_type_cmd;
 
+typedef enum _mg_feature_id
+{
+       mg_feature_id_transmode = 0x3
+} mg_feature_id;
+
+typedef enum _mg_feature_val
+{
+       mg_feature_val_trans_default = 0x0,
+       mg_feature_val_trans_vcmd = 0x3,
+       mg_feature_val_trand_vcmds = 0x2
+} mg_feature_val;
+
+typedef enum _mg_vcmd
+{
+       mg_vcmd_update_xipinfo = 0xFA, /* FWPATCH commmand through IOM I/O */
+       mg_vcmd_verify_fwpatch = 0xFB, /* FWPATCH commmand through IOM I/O */
+       mg_vcmd_update_stgdrvinfo = 0xFC, /* IOM identificatin info program command */
+       mg_vcmd_prep_fwpatch = 0xFD, /* FWPATCH commmand through IOM I/O */
+       mg_vcmd_exe_fwpatch = 0xFE, /* FWPATCH commmand through IOM I/O */
+       mg_vcmd_wr_pll = 0x8B,
+       mg_vcmd_purge_nand = 0x8C, /* Only for  Seagle */
+       mg_vcmd_lock_otp = 0x8D,
+       mg_vcmd_rd_otp = 0x8E,
+       mg_vcmd_wr_otp = 0x8F
+} mg_vcmd;
+
+typedef enum _mg_opmode
+{
+       mg_op_mode_xip = 1, /* TRUE XIP */
+       mg_op_mode_snd = 2, /* BOOT+Storage */
+       mg_op_mode_stg = 0  /* Only Storage */
+} mg_opmode;
+
 #endif

Linking to existing account procedure

If you already have an account and want to add another login method you MUST first sign in with your existing account and then change URL to read https://review.openocd.org/login/?link to get to this page again but this time it'll work for linking. Thank you.

SSH host keys fingerprints

1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=..              |
|+o..   .         |
|*.o   . .        |
|+B . . .         |
|Bo. = o S        |
|Oo.+ + =         |
|oB=.* = . o      |
| =+=.+   + E     |
|. .=o   . o      |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)