- added support for American Microsystem's M5960 (FT2232 based USB JTAG interface)
authordrath <drath@b42882b7-edfa-0310-969c-e2dbd0fdcd60>
Fri, 6 Oct 2006 15:46:25 +0000 (15:46 +0000)
committerdrath <drath@b42882b7-edfa-0310-969c-e2dbd0fdcd60>
Fri, 6 Oct 2006 15:46:25 +0000 (15:46 +0000)
- added support for AT91SAM7A devices (thanks to Magnus Lundin)
- updated README with pointer to Amontec's JTAGkeyTiny

git-svn-id: svn://svn.berlios.de/openocd/trunk@102 b42882b7-edfa-0310-969c-e2dbd0fdcd60

README
src/flash/at91sam7.c
src/flash/at91sam7.h
src/jtag/ft2232.c

diff --git a/README b/README
index a725a94..47cab62 100644 (file)
--- a/README
+++ b/README
@@ -43,6 +43,11 @@ The Amontec JTAGkey offers support for a wide variety of target voltages from
 1.4V to 5V. It also allows the JTAG lines and reset signals to be tri-stated,
 allowing easy interfacing with a wide variety of targets.
 
+* Amontec JTAGkey-Tiny: www.amontec.com
+The Amontec JTAGkey offers support for a wide variety of target voltages from
+2.8V to 5V. It also allows the reset signals to be tri-stated, allowing easy
+interfacing with a wide variety of targets.
+
 * Olimex ARM-USB-OCD: www.olimex.com
 The Olimex ARM-USB-OCD offers support for a wide vriety of target voltages from
 2.0V to 5V. It also allows targets to be powered from the ARM-USB-OCD and
index a8e390a..8491682 100644 (file)
@@ -63,7 +63,7 @@ int at91sam7_info(struct flash_bank_s *bank, char *buf, int buf_size);
 
 u32 at91sam7_get_flash_status(flash_bank_t *bank);
 void at91sam7_set_flash_mode(flash_bank_t *bank,int mode);
-u8 at91sam7_wait_status_busy(flash_bank_t *bank, int timeout);
+u32 at91sam7_wait_status_busy(flash_bank_t *bank, u32 waitbits, int timeout);
 int at91sam7_handle_gpnvm_command(struct command_context_s *cmd_ctx, char *cmd, char **args, int argc);
 
 flash_driver_t at91sam7_flash =
@@ -195,7 +195,7 @@ void at91sam7_read_clock_info(flash_bank_t *bank)
                at91sam7_info->mck_freq = tmp >> ((mckr & PMC_MCKR_PRES) >> 2);
 
        /* Forget old flash timing */
-       at91sam7_set_flash_mode(bank,0);
+       at91sam7_set_flash_mode(bank,FMR_TIMING_NONE);
 }
 
 /* Setup the timimg registers for nvbits or normal flash */
@@ -208,10 +208,20 @@ void at91sam7_set_flash_mode(flash_bank_t *bank,int mode)
        if (mode && (mode != at91sam7_info->flashmode))
        {
                /* Always round up (ceil) */
-               if (mode==1)
-                       /* main clocks in 1uS */
-                       fmcn = (at91sam7_info->mck_freq/1000000ul)+1;
-               else if (mode==2)
+              if (mode==FMR_TIMING_NVBITS)
+              {
+                     if (at91sam7_info->cidr_arch == 0x60)
+                     {                           
+                            /* AT91SAM7A3 uses master clocks in 100 ns */
+                            fmcn = (at91sam7_info->mck_freq/10000000ul)+1;
+                     }
+                     else
+                     {
+                            /* master clocks in 1uS for ARCH 0x7 types */
+                            fmcn = (at91sam7_info->mck_freq/1000000ul)+1;
+                     }
+              }
+              else if (mode==FMR_TIMING_FLASH)
                        /* main clocks in 1.5uS */
                        fmcn = (at91sam7_info->mck_freq/666666ul)+1;
 
@@ -230,11 +240,11 @@ void at91sam7_set_flash_mode(flash_bank_t *bank,int mode)
        at91sam7_info->flashmode = mode;                
 }
 
-u8 at91sam7_wait_status_busy(flash_bank_t *bank, int timeout)
+u32 at91sam7_wait_status_busy(flash_bank_t *bank, u32 waitbits, int timeout)
 {
        u32 status;
        
-       while ((!((status = at91sam7_get_flash_status(bank)) & 0x01)) && (timeout-- > 0))
+       while ((!((status = at91sam7_get_flash_status(bank)) & waitbits)) && (timeout-- > 0))
        {
                DEBUG("status: 0x%x", status);
                usleep(1000);
@@ -256,6 +266,7 @@ u8 at91sam7_wait_status_busy(flash_bank_t *bank, int timeout)
        return status;
 }
 
+
 /* Send one command to the AT91SAM flash controller */
 int at91sam7_flash_command(struct flash_bank_s *bank,u8 cmd,u16 pagen) 
 {
@@ -267,8 +278,18 @@ int at91sam7_flash_command(struct flash_bank_s *bank,u8 cmd,u16 pagen)
        target_write_u32(target, MC_FCR, fcr);
        DEBUG("Flash command: 0x%x, pagenumber:", fcr, pagen);
 
-       if (at91sam7_wait_status_busy(bank, 10)&0x0C) 
+       if ((at91sam7_info->cidr_arch == 0x60)&&((cmd==SLB)|(cmd==CLB)))
        {
+              /* Lock bit manipulation on AT91SAM7A3 waits for FC_FSR bit 1, EOL */
+              if (at91sam7_wait_status_busy(bank, MC_FSR_EOL, 10)&0x0C) 
+              {
+                     return ERROR_FLASH_OPERATION_FAILED;
+              }
+              return ERROR_OK;
+       }
+
+       if (at91sam7_wait_status_busy(bank, MC_FSR_FRDY, 10)&0x0C) 
+       {
                return ERROR_FLASH_OPERATION_FAILED;
        }               
        return ERROR_OK;
@@ -422,7 +443,7 @@ int at91sam7_read_part_info(struct flash_bank_s *bank)
                        at91sam7_info->target_name = "AT91SAM7A3";
                        at91sam7_info->num_lockbits = 16;
                        at91sam7_info->pagesize = 256;
-                       at91sam7_info->pages_in_lockregion = 64;
+                     at91sam7_info->pages_in_lockregion = 16;
                        at91sam7_info->num_pages = 16*64;
                }
                return ERROR_OK;
@@ -526,7 +547,7 @@ int at91sam7_erase(struct flash_bank_s *bank, int first, int last)
 
        /* Configure the flash controller timing */
        at91sam7_read_clock_info(bank); 
-       at91sam7_set_flash_mode(bank,2);
+       at91sam7_set_flash_mode(bank,FMR_TIMING_FLASH);
 
        if ((first == 0) && (last == (at91sam7_info->num_lockbits-1)))
        {
@@ -568,7 +589,7 @@ int at91sam7_protect(struct flash_bank_s *bank, int set, int first, int last)
        
        /* Configure the flash controller timing */
        at91sam7_read_clock_info(bank); 
-       at91sam7_set_flash_mode(bank,1);
+       at91sam7_set_flash_mode(bank,FMR_TIMING_NVBITS);
        
        for (lockregion=first;lockregion<=last;lockregion++) 
        {
@@ -638,7 +659,7 @@ int at91sam7_write(struct flash_bank_s *bank, u8 *buffer, u32 offset, u32 count)
        
        /* Configure the flash controller timing */     
        at91sam7_read_clock_info(bank); 
-       at91sam7_set_flash_mode(bank,2);
+       at91sam7_set_flash_mode(bank,FMR_TIMING_FLASH);
 
        for (pagen=first_page; pagen<last_page; pagen++) {
                if (bytes_remaining<dst_min_alignment) 
@@ -700,7 +721,7 @@ int at91sam7_info(struct flash_bank_s *bank, char *buf, int buf_size)
                return ERROR_FLASH_OPERATION_FAILED;
        }
        
-       printed = snprintf(buf, buf_size, "\nat91sam7 information:\n");
+       printed = snprintf(buf, buf_size, "\nat91sam7 information: Chip is %s\n",at91sam7_info->target_name);
        buf += printed;
        buf_size -= printed;
        
@@ -800,7 +821,7 @@ int at91sam7_handle_gpnvm_command(struct command_context_s *cmd_ctx, char *cmd,
 
        /* Configure the flash controller timing */
        at91sam7_read_clock_info(bank); 
-       at91sam7_set_flash_mode(bank,1);
+       at91sam7_set_flash_mode(bank,FMR_TIMING_NVBITS);
        
        if (at91sam7_flash_command(bank, flashcmd, (u16)(bit)) != ERROR_OK) 
        {
index e2412f8..0bb8f43 100644 (file)
@@ -86,7 +86,16 @@ typedef struct at91sam7_flash_bank_s
 #define  CGPB 0x0D
 #define  SSB  0x0F
 
+/* MC_FSR bit definitions */
+#define        MC_FSR_FRDY 1
+#define        MC_FSR_EOL 2
+
 /* AT91SAM7 constants */
 #define RC_FREQ  32000
 
+/*  FLASH_TIMING_MODES */
+#define  FMR_TIMING_NONE    0
+#define  FMR_TIMING_NVBITS  1
+#define  FMR_TIMING_FLASH   2
+
 #endif /* AT91SAM7_H */
index c1973a3..6bb4be9 100644 (file)
@@ -90,11 +90,13 @@ typedef struct ft2232_layout_s
 int usbjtag_init(void);
 int jtagkey_init(void);
 int olimex_jtag_init(void);
+int m5960_init(void);
 
 /* reset procedures for supported layouts */
 void usbjtag_reset(int trst, int srst);
 void jtagkey_reset(int trst, int srst);
 void olimex_jtag_reset(int trst, int srst);
+void m5960_reset(int trst, int srst);
 
 /* blink procedures for layouts that support a blinking led */
 void olimex_jtag_blink(void);
@@ -106,6 +108,7 @@ ft2232_layout_t ft2232_layouts[] =
        {"jtagkey_prototype_v1", jtagkey_init, jtagkey_reset, NULL},
        {"signalyzer", usbjtag_init, usbjtag_reset, NULL},
        {"olimex-jtag", olimex_jtag_init, olimex_jtag_reset, olimex_jtag_blink},
+       {"m5960", m5960_init, m5960_reset, NULL},
        {NULL, NULL, NULL},
 };
 
@@ -718,6 +721,34 @@ void olimex_jtag_reset(int trst, int srst)
     DEBUG("trst: %i, srst: %i, high_output: 0x%2.2x, high_direction: 0x%2.2x", trst, srst, high_output, high_direction);
 }
 
+void m5960_reset(int trst, int srst)
+{
+       if (trst == 1)
+       {
+               cur_state = TAP_TLR;
+               low_output &= ~nTRST;
+       }
+       else if (trst == 0)
+       {
+               low_output |= nTRST;
+       }
+
+    if (srst == 1)
+    {
+        low_output |= nSRST;
+    }
+    else if (srst == 0)
+    {
+        low_output &= ~nSRST;
+    }
+
+    /* command "set data bits low byte" */
+    BUFFER_ADD = 0x80;
+    BUFFER_ADD = low_output;
+    BUFFER_ADD = low_direction;
+    DEBUG("trst: %i, srst: %i, high_output: 0x%2.2x, high_direction: 0x%2.2x", trst, srst, high_output, high_direction);
+}
+
 int ft2232_execute_queue()
 {
        jtag_command_t *cmd = jtag_command_queue; /* currently processed command */
@@ -1304,6 +1335,52 @@ int olimex_jtag_init(void)
        return ERROR_OK;
 }
 
+int m5960_init(void)
+{
+       u8 buf[3];
+       u32 bytes_written;
+       
+       low_output = 0x18;
+       low_direction = 0xfb;
+       
+       /* initialize low byte for jtag */
+       buf[0] = 0x80; /* command "set data bits low byte" */
+       buf[1] = low_output; /* value (TMS=1,TCK=0, TDI=0, nOE=0) */
+       buf[2] = low_direction; /* dir (output=1), TCK/TDI/TMS=out, TDO=in, nOE[12]=out, n[ST]srst=out */
+       DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
+       
+       if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+       {
+               ERROR("couldn't initialize FT2232 with 'm5960' layout"); 
+               return ERROR_JTAG_INIT_FAILED;
+       }
+       
+       nTRST = 0x10;
+       nTRSTnOE = 0x0; /* not output enable for nTRST */
+       nSRST = 0x20;
+       nSRSTnOE = 0x00; /* no output enable for nSRST */
+
+       high_output = 0x00;
+       high_direction = 0x0c;
+
+       /* turn red LED1 on, LED2 off */
+       high_output |= 0x08;
+       
+       /* initialize high port */
+       buf[0] = 0x82; /* command "set data bits high byte" */
+       buf[1] = high_output; /* value */
+       buf[2] = high_direction;   /* all outputs (xRST and xRSTnOE) */
+       DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
+       
+       if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+       {
+               ERROR("couldn't initialize FT2232 with 'm5960' layout"); 
+               return ERROR_JTAG_INIT_FAILED;
+       }
+       
+       return ERROR_OK;
+}
+
 void olimex_jtag_blink(void)
 {
        /* Olimex ARM-USB-OCD has a LED connected to ACBUS3