Olimex SAM9-L9260 board configuration update.

This updates the board configuration for the SAM9-L9260 board with the
configuration for the on-board NAND and dataflash.  Included are commands
for configuring the AT91SAM9 NAND flash driver.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

diff --git a/tcl/board/olimex_sam9_l9260.cfg b/tcl/board/olimex_sam9_l9260.cfg
index 5c4714e199652200265ae7477944bf7f85d67d7d..7c4b2ccb0a63bf4424b1648edafe588a83a8e4bf 100644 (file)
--- a/tcl/board/olimex_sam9_l9260.cfg
+++ b/tcl/board/olimex_sam9_l9260.cfg
@@ -35,6 +35,7 @@ $_TARGETNAME configure -event reset-init {
        ##
        # Clock configuration for 99.328 MHz main clock.
        ##
+    puts "Setting up clock"
        mww 0xfffffc20 0x00004001 # CKGR_MOR : enable main oscillator, 512 slow clock startup
        sleep 20                  # wait 20 ms (need 15.6 ms for startup)
        mww 0xfffffc30 0x00000001 # PMC_MCKR : switch to main oscillator (18.432 MHz)
@@ -53,6 +54,7 @@ $_TARGETNAME configure -event reset-init {
        ##
        # SDRAM configuration for 2 x Samsung K4S561632J-UC75, 4M x 16Bit x 4 Banks.
        ##
+    puts "Configuring SDRAM"
        mww 0xfffff870 0xffff0000 # PIOC_ASR : select peripheral function for D15..D31
        mww 0xfffff804 0xffff0000 # PIOC_PDR : disable PIO function for D15..D31
        
@@ -86,4 +88,54 @@ $_TARGETNAME configure -event reset-init {
        mww 0x20000000 0
        
        mww 0xffffea04 0x2b6      # SDRAMC_TR : set refresh timer count to 7 us
+
+    ##
+    # NAND Flash Configuration for 1 x Samsung K9F4G08U0M, 512M x 8Bit.
+    ##
+    puts "Configuring NAND flash"
+    mww 0xfffffc10 0x00000010 ;# PMC_PCER : enable PIOC clock
+    mww 0xfffff800 0x00006000 ;# PIOC_PER : enable PIO function for 13(RDY/~BSY) and 14(~CS)
+    mww 0xfffff810 0x00004000 ;# PIOC_OER : enable output on 14
+    mww 0xfffff814 0x00002000 ;# PIOC_ODR : disable output on 13
+    mww 0xfffff830 0x00004000 ;# PIOC_SODR : set 14 to disable NAND
+    mww 0xfffff864 0x00002000 ;# PIOC_PUER : enable pull-up on 13
+    
+    mww 0xffffef1c 0x0001000A ;# EBI_CSA : assign EBI CS3 to NAND, same settings as before
+    
+    mww 0xffffec30 0x00010001 ;# SMC_SETUP3 : 1 clock cycle setup for NRD and NWE
+    mww 0xffffec34 0x03030303 ;# SMC_PULSE3 : 3 clock cycle pulse for all signals
+    mww 0xffffec38 0x00050005 ;# SMC_CYCLE3 : 5 clock cycle NRD and NWE cycle
+    mww 0xffffec3C 0x00020003 ;# SMC_MODE3 : NRD and NWE control, no NWAIT, 8-bit DBW, 
+                               #             3 TDF cycles, no optimization
+    
+    mww 0xffffe800 0x00000001 ;# ECC_CR : reset the ECC parity registers
+    mww 0xffffe804 0x00000002 ;# ECC_MR : page size is 2112 words (word is 8 bits)
+    
+    nand probe at91sam9260.flash
+    
+    ##
+    # Dataflash configuration for 1 x Atmel AT45DB161D, 16Mbit
+    ##
+    puts "Setting up dataflash"
+    mww 0xfffff404 0x00000807 ;# PIOA_PDR : disable PIO function for 0(SPI0_MISO), 1(SPI0_MOSI), 
+                               #            2(SPI0_SPCK), and 11(SPI0_NPCS1)
+    mww 0xfffff470 0x00000007 ;# PIOA_ASR : select peripheral A function for 0, 1, and 2
+    mww 0xfffff474 0x00000800 ;# PIOA_BSR : select peripheral B function for 11
+    mww 0xfffffc10 0x00001000 ;# PMC_PCER : enable SPI0 clock
+    
+    mww 0xfffc8000 0x00000080 ;# SPI0_CR : software reset SPI0
+    mww 0xfffc8000 0x00000080 ;# SPI0_CR : again to be sure
+    mww 0xfffc8004 0x000F0011 ;# SPI0_MR : master mode with nothing selected
+    
+    mww 0xfffc8034 0x011a0302 ;# SPI0_CSR1 : capture on leading edge, 8-bits/tx. 33MHz baud, 
+                               #             250ns delay before SPCK, 250ns b/n tx
+    
+    mww 0xfffc8004 0x000D0011 ;# SPI0_MR : same config, select NPCS1
+    mww 0xfffc8000 0x00000001 ;# SPI0_CR : enable SPI0
 }
+
+nand device at91sam9260.flash at91sam9 at91sam9260.cpu 0x40000000 0xffffe800
+at91sam9 cle 0 22
+at91sam9 ale 0 21
+at91sam9 rdy_busy 0 0xfffff800 13
+at91sam9 ce 0 0xfffff800 14