Flash protection set on a device with MANW=1 was lost after reset.
Since #2903 the driver honored MANW bit and issued Write Page command just
for main flash write. This change adds similar technique to
samd_modify_user_row().
Minor code improvements:
samd_check_error() returns error code corresponding to error type
instead of bool.
samd_check_error() does not clear STATUS register if no error bit is set.
Eliminated double error check in call sequence samd_issue_nvmctrl_command()
folowed by samd_check_error().
Missing error code ERROR_FLASH_PROTECTED added to src/flash/common.h.
Change-Id: Icf59ab8803305d0cb3170c8a5089b8f9828b99f8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3550
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
#define ERROR_FLASH_SECTOR_NOT_ERASED (-906)
#define ERROR_FLASH_BANK_NOT_PROBED (-907)
#define ERROR_FLASH_OPER_UNSUPPORTED (-908)
#define ERROR_FLASH_SECTOR_NOT_ERASED (-906)
#define ERROR_FLASH_BANK_NOT_PROBED (-907)
#define ERROR_FLASH_OPER_UNSUPPORTED (-908)
+#define ERROR_FLASH_PROTECTED (-909)
#endif /* OPENOCD_FLASH_COMMON_H */
#endif /* OPENOCD_FLASH_COMMON_H */
-static bool samd_check_error(struct target *target)
+static int samd_check_error(struct target *target)
uint16_t status;
ret = target_read_u16(target,
SAMD_NVMCTRL + SAMD_NVMCTRL_STATUS, &status);
if (ret != ERROR_OK) {
LOG_ERROR("Can't read NVM status");
uint16_t status;
ret = target_read_u16(target,
SAMD_NVMCTRL + SAMD_NVMCTRL_STATUS, &status);
if (ret != ERROR_OK) {
LOG_ERROR("Can't read NVM status");
- if (status & 0x001C) {
- if (status & (1 << 4)) /* NVME */
- LOG_ERROR("SAMD: NVM Error");
- if (status & (1 << 3)) /* LOCKE */
- LOG_ERROR("SAMD: NVM lock error");
- if (status & (1 << 2)) /* PROGE */
- LOG_ERROR("SAMD: NVM programming error");
+ if ((status & 0x001C) == 0)
+ return ERROR_OK;
- error = true;
- } else {
- error = false;
+ if (status & (1 << 4)) { /* NVME */
+ LOG_ERROR("SAMD: NVM Error");
+ ret = ERROR_FLASH_OPERATION_FAILED;
+ }
+
+ if (status & (1 << 3)) { /* LOCKE */
+ LOG_ERROR("SAMD: NVM lock error");
+ ret = ERROR_FLASH_PROTECTED;
+ }
+
+ if (status & (1 << 2)) { /* PROGE */
+ LOG_ERROR("SAMD: NVM programming error");
+ ret = ERROR_FLASH_OPER_UNSUPPORTED;
}
/* Clear the error conditions by writing a one to them */
}
/* Clear the error conditions by writing a one to them */
- ret = target_write_u16(target,
+ ret2 = target_write_u16(target,
SAMD_NVMCTRL + SAMD_NVMCTRL_STATUS, status);
SAMD_NVMCTRL + SAMD_NVMCTRL_STATUS, status);
LOG_ERROR("Can't clear NVM error conditions");
LOG_ERROR("Can't clear NVM error conditions");
}
static int samd_issue_nvmctrl_command(struct target *target, uint16_t cmd)
}
static int samd_issue_nvmctrl_command(struct target *target, uint16_t cmd)
return res;
/* Check to see if the NVM command resulted in an error condition. */
return res;
/* Check to see if the NVM command resulted in an error condition. */
- if (samd_check_error(target))
- return ERROR_FAIL;
-
- return ERROR_OK;
+ return samd_check_error(target);
}
static int samd_erase_row(struct target *target, uint32_t address)
}
static int samd_erase_row(struct target *target, uint32_t address)
uint8_t startb, uint8_t endb)
{
int res;
uint8_t startb, uint8_t endb)
{
int res;
+ uint32_t nvm_ctrlb;
+ bool manual_wp = true;
if (is_user_row_reserved_bit(startb) || is_user_row_reserved_bit(endb)) {
LOG_ERROR("Can't modify bits in the requested range");
return ERROR_FAIL;
}
if (is_user_row_reserved_bit(startb) || is_user_row_reserved_bit(endb)) {
LOG_ERROR("Can't modify bits in the requested range");
return ERROR_FAIL;
}
+ /* Check if we need to do manual page write commands */
+ res = target_read_u32(target, SAMD_NVMCTRL + SAMD_NVMCTRL_CTRLB, &nvm_ctrlb);
+ if (res == ERROR_OK)
+ manual_wp = (nvm_ctrlb & SAMD_NVM_CTRLB_MANW) != 0;
+
/* Retrieve the MCU's page size, in bytes. This is also the size of the
* entire User Row. */
uint32_t page_size;
/* Retrieve the MCU's page size, in bytes. This is also the size of the
* entire User Row. */
uint32_t page_size;
if (!buf)
return ERROR_FAIL;
if (!buf)
return ERROR_FAIL;
- /* Read the user row (comprising one page) by half-words. */
- res = target_read_memory(target, SAMD_USER_ROW, 2, page_size / 2, buf);
+ /* Read the user row (comprising one page) by words. */
+ res = target_read_memory(target, SAMD_USER_ROW, 4, page_size / 4, buf);
if (res != ERROR_OK)
goto out_user_row;
if (res != ERROR_OK)
goto out_user_row;
/* Modify */
buf_set_u32(buf, startb, endb - startb + 1, value);
/* Modify */
buf_set_u32(buf, startb, endb - startb + 1, value);
- /* Write the page buffer back out to the target. A Flash write will be
- * triggered automatically. */
+ /* Write the page buffer back out to the target. */
res = target_write_memory(target, SAMD_USER_ROW, 4, page_size / 4, buf);
if (res != ERROR_OK)
goto out_user_row;
res = target_write_memory(target, SAMD_USER_ROW, 4, page_size / 4, buf);
if (res != ERROR_OK)
goto out_user_row;
- if (samd_check_error(target)) {
- res = ERROR_FAIL;
- goto out_user_row;
+ if (manual_wp) {
+ /* Trigger flash write */
+ res = samd_issue_nvmctrl_command(target, SAMD_NVM_CMD_WAP);
+ } else {
+ res = samd_check_error(target);
- /* Success */
- res = ERROR_OK;
-
* then issue CMD_WP always */
if (manual_wp || pg_offset + 4 * nw < chip->page_size) {
res = samd_issue_nvmctrl_command(bank->target, SAMD_NVM_CMD_WP);
* then issue CMD_WP always */
if (manual_wp || pg_offset + 4 * nw < chip->page_size) {
res = samd_issue_nvmctrl_command(bank->target, SAMD_NVM_CMD_WP);
- if (res != ERROR_OK) {
- LOG_ERROR("%s: %d", __func__, __LINE__);
- goto free_pb;
- }
- }
+ } else {
+ /* Access through AHB is stalled while flash is being programmed */
+ usleep(200);
- /* Access through AHB is stalled while flash is being programmed */
- usleep(200);
+ res = samd_check_error(bank->target);
+ }
- if (samd_check_error(bank->target)) {
LOG_ERROR("%s: write failed at address 0x%08" PRIx32, __func__, address);
LOG_ERROR("%s: write failed at address 0x%08" PRIx32, __func__, address);
Linking to existing account procedure
If you already have an account and want to add another login method
you
MUST first sign in with your existing account and
then change URL to read
https://review.openocd.org/login/?link
to get to this page again but this time it'll work for linking. Thank you.
SSH host keys fingerprints
1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=.. |
|+o.. . |
|*.o . . |
|+B . . . |
|Bo. = o S |
|Oo.+ + = |
|oB=.* = . o |
| =+=.+ + E |
|. .=o . o |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)