Commit
87a4158acf56 ("drivers: xds110: Clean up command syntax and
documentation") does not follow the documentation structure that
lists the adapters in cpt 2 "Debug Adapter Hardware" then lists
the adapter commands in cpt 8.2 "Interface Drivers"; it puts all
in cpt 2.
While doing that, uses an incorrect texinfo syntax that causes the
following warnings at compile time:
doc/openocd.texi:543: warning: @deffn should only appear at the beginning of a line
doc/openocd.texi:547: warning: @deffn should only appear at the beginning of a line
doc/openocd.texi:552: warning: @deffn should only appear at the beginning of a line
Move the documentation of xds110 commands in the proper chapter
and fix the texinfo syntax.
Change-Id: I0b3f0fe0c687f194bb02e2d81aca86fcd4fdd718
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 87a4158acf56 ("drivers: xds110: Clean up command syntax and documentation")
Reviewed-on: http://openocd.zylin.com/5613
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Edward Fewell <efewell@ti.com>
@* Link: @url{http://www.keil.com/ulink1/}
@item @b{TI XDS110 Debug Probe}
@* Link: @url{http://www.keil.com/ulink1/}
@item @b{TI XDS110 Debug Probe}
-@* The XDS110 is included as the embedded debug probe on many Texas Instruments
-LaunchPad evaluation boards. The XDS110 is also available as a stand-alone USB
-debug probe with the added capability to supply power to the target board. The
-following commands are supported by the XDS110 driver:
-@*@deffn {Config Command} {xds110 serial} serial_string
-Specifies the serial number of which XDS110 probe to use. Otherwise, the first
-XDS110 found will be used.
-@end deffn
-@*@deffn {Config Command} {xds110 supply} voltage_in_millivolts
-Available only on the XDS110 stand-alone probe. Sets the voltage level of the
-XDS110 power supply. A value of 0 leaves the supply off. Otherwise, the supply
-can be set to any value in the range 1800 to 3600 millivolts.
-@end deffn
-@*@deffn {Command} {xds110 info}
-Displays information about the connected XDS110 debug probe (e.g. firmware
-version).
-@end deffn
-@* Further information can be found at the following sites:
@* Link: @url{https://software-dl.ti.com/ccs/esd/documents/xdsdebugprobes/emu_xds110.html}
@* Link: @url{https://software-dl.ti.com/ccs/esd/documents/xdsdebugprobes/emu_xds_software_package_download.html#xds110-support-utilities}
@end itemize
@* Link: @url{https://software-dl.ti.com/ccs/esd/documents/xdsdebugprobes/emu_xds110.html}
@* Link: @url{https://software-dl.ti.com/ccs/esd/documents/xdsdebugprobes/emu_xds_software_package_download.html#xds110-support-utilities}
@end itemize
This is the Keil ULINK v1 JTAG debugger.
@end deffn
This is the Keil ULINK v1 JTAG debugger.
@end deffn
+@deffn {Interface Driver} {xds110}
+The XDS110 is included as the embedded debug probe on many Texas Instruments
+LaunchPad evaluation boards. The XDS110 is also available as a stand-alone USB
+debug probe with the added capability to supply power to the target board. The
+following commands are supported by the XDS110 driver:
+
+@deffn {Config Command} {xds110 serial} serial_string
+Specifies the serial number of which XDS110 probe to use. Otherwise, the first
+XDS110 found will be used.
+@end deffn
+
+@deffn {Config Command} {xds110 supply} voltage_in_millivolts
+Available only on the XDS110 stand-alone probe. Sets the voltage level of the
+XDS110 power supply. A value of 0 leaves the supply off. Otherwise, the supply
+can be set to any value in the range 1800 to 3600 millivolts.
+@end deffn
+
+@deffn {Command} {xds110 info}
+Displays information about the connected XDS110 debug probe (e.g. firmware
+version).
+@end deffn
+@end deffn
+
@deffn {Interface Driver} {xlnx_pcie_xvc}
This driver supports the Xilinx Virtual Cable (XVC) over PCI Express.
It is commonly found in Xilinx based PCI Express designs. It allows debugging
@deffn {Interface Driver} {xlnx_pcie_xvc}
This driver supports the Xilinx Virtual Cable (XVC) over PCI Express.
It is commonly found in Xilinx based PCI Express designs. It allows debugging
Linking to existing account procedure
If you already have an account and want to add another login method
you
MUST first sign in with your existing account and
then change URL to read
https://review.openocd.org/login/?link
to get to this page again but this time it'll work for linking. Thank you.
SSH host keys fingerprints
1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=.. |
|+o.. . |
|*.o . . |
|+B . . . |
|Bo. = o S |
|Oo.+ + = |
|oB=.* = . o |
| =+=.+ + E |
|. .=o . o |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)