lm3s811-ek uses generic stellaris target config

There's no point in an lm3s811-specific target file,
so remove it in favor of the generic "stellaris.cfg".

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

diff --git a/NEWS b/NEWS
index 2dd14cc60e2edfc86dd0fc7918346760ada37dad..bb746fa1ca98dd3ddf950ecf2aea29cd1bd23940 100644 (file)
--- a/NEWS
+++ b/NEWS
@@ -49,6 +49,7 @@ Board, Target, and Interface Configuration Scripts:
        Support Voipac PXA270/PXA270M module.
        New $PARPORTADDR tcl variable used to change default
                parallel port address used.
+       Remove lm3s811.cfg; use "stellaris.cfg" instead
 
 Core Jim/TCL Scripting:
        New "add_script_search_dir" command, behaviour is the same

diff --git a/tcl/board/ek-lm3s811.cfg b/tcl/board/ek-lm3s811.cfg
index 7d3f2ce345b4d187f10c39768cd5cc0767254085..66519f674f22702c60c3acee2817f2e424ee282d 100644 (file)
--- a/tcl/board/ek-lm3s811.cfg
+++ b/tcl/board/ek-lm3s811.cfg
@@ -4,13 +4,14 @@
 # http://www.luminarymicro.com/products/stellaris_811_evaluation_kits.html
 
 # include the FT2232 interface config for on-board JTAG interface
+# NOTE:  older '811-EK boards (before rev C) shouldn't use this.
 source [find interface/luminary.cfg]
 
+   set  CHIPNAME lm3s811
+
 # include the target config
-source [find target/lm3s811.cfg]
+source [find target/stellaris.cfg]
 
-# jtag speed
-adapter_khz 500
 
 adapter_nsrst_delay 100
 

diff --git a/tcl/target/lm3s811.cfg b/tcl/target/lm3s811.cfg
deleted file mode 100644 (file)
index 49879d0..0000000
--- a/tcl/target/lm3s811.cfg
+++ /dev/null
@@ -1,29 +0,0 @@
-# Script for TI/Luminary Stellaris LM3S811
-
-if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
-} else {
-   set  _CHIPNAME lm3s811
-}
-
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-   set _CPUTAPID 0x3ba00477
-}
-
-#jtag scan chain
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 1 -irmask 0xf -expected-id $_CPUTAPID
-
-# the luminary variant causes a software reset rather than asserting SRST
-# this stops the debug registers from being cleared
-# this will be fixed in later revisions of silicon
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m3 -chain-position $_CHIPNAME.cpu -variant lm3s
-
-# 8k working area at base of ram, not backed up
-$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 0x2000
-
-#flash configuration
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME stellaris 0 0 0 0 $_TARGETNAME