also remove legacy footnote as it adds no value.
Change-Id: I3892acf244bd8fba6f844a5d82a66004e193a395
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/4309
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
families from Texas Instruments include internal flash. The driver
automatically recognizes a number of these chips using the chip
identification register, and autoconfigures itself.
families from Texas Instruments include internal flash. The driver
automatically recognizes a number of these chips using the chip
identification register, and autoconfigures itself.
-@footnote{Currently there is a @command{stellaris mass_erase} command.
-That seems pointless since the same effect can be had using the
-standard @command{flash erase_address} command.}
@example
flash bank $_FLASHNAME stellaris 0 0 0 0 $_TARGETNAME
@example
flash bank $_FLASHNAME stellaris 0 0 0 0 $_TARGETNAME
flash bank $_FLASHNAME stm32f1x 0x08080000 0 0 0 $_TARGETNAME
@end example
flash bank $_FLASHNAME stm32f1x 0x08080000 0 0 0 $_TARGETNAME
@end example
-Some stm32f1x-specific commands
-@footnote{Currently there is a @command{stm32f1x mass_erase} command.
-That seems pointless since the same effect can be had using the
-standard @command{flash erase_address} command.}
-are defined:
+Some stm32f1x-specific commands are defined:
@deffn Command {stm32f1x lock} num
Locks the entire stm32 device.
@deffn Command {stm32f1x lock} num
Locks the entire stm32 device.
@end deffn
@deffn Command {stm32f1x mass_erase} num
@end deffn
@deffn Command {stm32f1x mass_erase} num
-Mass erases the entire stm32f1x device. This is the only way to
-unlock a protected flash (unless RDP Level is 2 which can't be unlocked at all).
+Mass erases the entire stm32f1x device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@end deffn
@deffn Command {stm32f2x mass_erase} num
@end deffn
@deffn Command {stm32f2x mass_erase} num
-Mass erases the entire stm32f2x device. This is the only way to
-unlock a protected flash (unless RDP Level is 2 which can't be unlocked at all).
+Mass erases the entire stm32f2x device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@end deffn
@deffn Command {stm32h7x mass_erase} num
@end deffn
@deffn Command {stm32h7x mass_erase} num
-Mass erases the entire stm32h7x device. This is the only way to
-unlock a protected flash (unless RDP Level is 2 which can't be unlocked at all).
+Mass erases the entire stm32h7x device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@end deffn
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@end deffn
Some stm32lx-specific commands are defined:
Some stm32lx-specific commands are defined:
+@deffn Command {stm32lx lock} num
+Locks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32lx unlock} num
+Unlocks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
@deffn Command {stm32lx mass_erase} num
Mass erases the entire stm32lx device (all flash banks and EEPROM
data). This is the only way to unlock a protected flash (unless RDP
@deffn Command {stm32lx mass_erase} num
Mass erases the entire stm32lx device (all flash banks and EEPROM
data). This is the only way to unlock a protected flash (unless RDP
@end deffn
@deffn Command {stm32l4x mass_erase} num
@end deffn
@deffn Command {stm32l4x mass_erase} num
-Mass erases the entire stm32l4x device. This is the only way to
-unlock a protected flash (unless RDP Level is 2 which can't be unlocked at all).
+Mass erases the entire stm32l4x device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@end deffn
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@end deffn
Linking to existing account procedure
If you already have an account and want to add another login method
you
MUST first sign in with your existing account and
then change URL to read
https://review.openocd.org/login/?link
to get to this page again but this time it'll work for linking. Thank you.
SSH host keys fingerprints
1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=.. |
|+o.. . |
|*.o . . |
|+B . . . |
|Bo. = o S |
|Oo.+ + = |
|oB=.* = . o |
| =+=.+ + E |
|. .=o . o |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)