X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=testing%2Fexamples%2Fledtest-imx31pdk%2Fgdbinit-imx31pdk;h=304a8d8992f011075e4ea82b0cdf87a0f0084d9f;hp=5b78daa261b1c8e6abde206815972fbede81e3a3;hb=8fc9bcb7f57306e822deaf2e0facd51b96dc4fb2;hpb=9094500ba60b677a9c93e970ec741d2fc8f0c89a

diff --git a/testing/examples/ledtest-imx31pdk/gdbinit-imx31pdk b/testing/examples/ledtest-imx31pdk/gdbinit-imx31pdk
index 5b78daa261..304a8d8992 100644
--- a/testing/examples/ledtest-imx31pdk/gdbinit-imx31pdk
+++ b/testing/examples/ledtest-imx31pdk/gdbinit-imx31pdk
@@ -1,4 +1,8 @@
-echo Setting up for the FreeScale iMX31 Board.\n
+echo Script to load ledtest on iMX31PDK.\n
+
+# Note: you need to startup openocd with "-f board/imx31pdk.cfg"
+# in order to it initialize RAM memory.
+
 # SETUP GDB :
 #
 # Common gdb setup for ARM CPUs
@@ -9,104 +13,8 @@ set prompt (arm-gdb)
 set endian little
 dir .
 
-# DEFINE MACROS	:
-#
-# Create a "refresh" macro to update gdb's screens after the cpu
-# has been stopped by the other CPU or following an "monitor allstop"
-define refresh
-	monitor set hbreak
-	cont
-	monitor clear hbreak
-end
-
 # CONNECT TO TARGET :
 target remote 127.0.0.1:3333
-monitor reset run
-#FIX!!!! should be reset init!
-monitor reset halt
-
-# iMX31 PDK board initialization commands:
-
-#// init_ccm
-
-monitor mww 0x53FC0000 0x040
-monitor mww 0x53F80000 0x074B0B7D
-
-#//532-133-66.5
-#//monitor mww 0x53F80004 0xFF871D58
-#//monitor mww 0x53F80010 0x0033280C
-
-#// 399MHz - 26MHz input, PD=1,MFI=7, MFN=27, MFD=40
-monitor mww 0x53F80004 0xFF871D50
-monitor mww 0x53F80010 0x00271C1B
-
-#// 208-104-52
-#//monitor mww 0x53F80004 0xFF871D48
-#//monitor mww 0x53F80010 0x04002000
-
-#// Configure CPLD on CS5 
-monitor mww 0xb8002050 0x0000DCF6
-monitor mww 0xb8002054 0x444A4541
-monitor mww 0xb8002058 0x44443302
-
-#// Disable maximum drive strength for SDRAM/DDR lines by clearing DSE1 bits
-#// in SW_PAD_CTL registers
-
-#// SDCLK
-monitor mww 0x43FAC26C 0
-
-#// CAS
-monitor mww 0x43FAC270 0
-
-#// RAS
-monitor mww 0x43FAC274 0
-
-#// CS2 (CSD0)
-monitor mww 0x43FAC27C 0x1000
-
-#// DQM3
-monitor mww 0x43FAC284 0
-
-#// DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC)
-monitor mww 0x43FAC288 0
-monitor mww 0x43FAC28C 0
-monitor mww 0x43FAC290 0
-monitor mww 0x43FAC294 0
-monitor mww 0x43FAC298 0
-monitor mww 0x43FAC29C 0
-monitor mww 0x43FAC2A0 0
-monitor mww 0x43FAC2A4 0
-monitor mww 0x43FAC2A8 0
-monitor mww 0x43FAC2AC 0
-monitor mww 0x43FAC2B0 0
-monitor mww 0x43FAC2B4 0
-monitor mww 0x43FAC2B8 0
-monitor mww 0x43FAC2BC 0
-monitor mww 0x43FAC2C0 0
-monitor mww 0x43FAC2C4 0
-monitor mww 0x43FAC2C8 0
-monitor mww 0x43FAC2CC 0
-monitor mww 0x43FAC2D0 0
-monitor mww 0x43FAC2D4 0
-monitor mww 0x43FAC2D8 0
-monitor mww 0x43FAC2DC 0
-
-#// Initialization script for 32 bit DDR on MX31 PDK
-monitor mww 0xB8001010 0x00000004
-monitor mww 0xB8001004 0x006ac73a
-monitor mww 0xB8001000 0x92100000
-monitor mww 0x80000f00 0x12344321
-monitor mww 0xB8001000 0xa2100000
-monitor mww 0x80000000 0x12344321
-monitor mww 0x80000000 0x12344321
-monitor mww 0xB8001000 0xb2100000
-#monitor char 0x80000033 0xda
-monitor mwb 0x80000033 0xda
-#monitor char 0x81000000 0xff
-monitor mwb 0x81000000 0xff
-monitor mww 0xB8001000 0x82226080
-monitor mww 0x80000000 0xDEADBEEF
-monitor mww 0xB8001010 0x0000000c
 
 #  LOAD IMAGE :
 #