X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=tcl%2Ftarget%2Fstm32.cfg;h=217b79d9625c30975d15ce4e7ba9d65b409348d1;hp=97d76789e7327dc1151ab7f4a483139822a76885;hb=951d1850494a404f775c141e44376d42760563c9;hpb=2120231afd710ce6720b82838810240195122b5a

diff --git a/tcl/target/stm32.cfg b/tcl/target/stm32.cfg
index 97d76789e7..217b79d962 100644
--- a/tcl/target/stm32.cfg
+++ b/tcl/target/stm32.cfg
@@ -1,71 +1,3 @@
-# script for stm32
-
-if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
-} else {
-   set  _CHIPNAME stm32
-}
-
-if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
-} else {
-   set  _ENDIAN little
-}
-
-# Work-area is a space in RAM used for flash programming
-# By default use 16kB
-if { [info exists WORKAREASIZE] } {
-   set  _WORKAREASIZE $WORKAREASIZE
-} else {
-   set  _WORKAREASIZE 0x4000
-}
-
-# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
-jtag_khz 1000
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-  # See STM Document RM0008
-  # Section 26.6.3
-   set _CPUTAPID 0x3ba00477
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID ] } {
-   # FIXME this never gets used to override defaults...
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0008
-  # Section 29.6.2
-  # Low density devices, Rev A
-  set _BSTAPID1 0x06412041
-  # Medium density devices, Rev A
-  set _BSTAPID2 0x06410041
-  # Medium density devices, Rev B and Rev Z
-  set _BSTAPID3 0x16410041
-  # High density devices, Rev A
-  set _BSTAPID4 0x06414041
-  # Connectivity line devices, Rev A and Rev Z
-  set _BSTAPID5 0x06418041
-}
-jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
-	-expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
-	-expected-id $_BSTAPID4 -expected-id $_BSTAPID5
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
-
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
-
-flash bank stm32x 0 0 0 0 $_TARGETNAME
-
-# For more information about the configuration files, take a look at:
-# openocd.texi
+# deprecated cfg file
+echo "DEPRECATED! use script 'target/stm32f1x.cfg' not 'target/stm32.cfg'"
+source [find target/stm32f1x.cfg]