X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=tcl%2Ftarget%2Fsam7x256.cfg;h=c3f7cd9cae3115887b86628e5332e82188b3bb88;hp=789f7dd69ca0caeb531765632002b306aeac25be;hb=f86137066a6b42c46c457c9837a8015990bf71e6;hpb=dbbc9c41f7db210b0a4e226540a28e0a8a5019bf

diff --git a/tcl/target/sam7x256.cfg b/tcl/target/sam7x256.cfg
index 789f7dd69c..c3f7cd9cae 100644
--- a/tcl/target/sam7x256.cfg
+++ b/tcl/target/sam7x256.cfg
@@ -1,15 +1,15 @@
 #use combined on interfaces or targets that can't set TRST/SRST separately
 reset_config srst_only srst_pulls_trst
 
-if { [info exists CHIPNAME] } {	
-   set  _CHIPNAME $CHIPNAME    
-} else {	 
+if { [info exists CHIPNAME] } {
+   set  _CHIPNAME $CHIPNAME
+} else {
    set  _CHIPNAME sam7x256
 }
 
-if { [info exists ENDIAN] } {	
-   set  _ENDIAN $ENDIAN    
-} else {	 
+if { [info exists ENDIAN] } {
+   set  _ENDIAN $ENDIAN
+} else {
    set  _ENDIAN little
 }
 
@@ -21,29 +21,29 @@ if { [info exists CPUTAPID ] } {
 
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-
+set _TARGETNAME $_CHIPNAME.cpu
 target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi
-$_TARGETNAME configure -event reset-init { 
+
+$_TARGETNAME configure -event reset-init {
 	# disable watchdog
-	mww 0xfffffd44 0x00008000	
+	mww 0xfffffd44 0x00008000
 	# enable user reset
-	mww 0xfffffd08 0xa5000001	
+	mww 0xfffffd08 0xa5000001
 	# CKGR_MOR : enable the main oscillator
-	mww 0xfffffc20 0x00000601	
+	mww 0xfffffc20 0x00000601
 	sleep 10
 	# CKGR_PLLR: 96.1097 MHz
-	mww 0xfffffc2c 0x00481c0e 	
+	mww 0xfffffc2c 0x00481c0e
 	sleep 10
 	# PMC_MCKR : MCK = PLL / 2 ~= 48 MHz
-	mww 0xfffffc30 0x00000007	
+	mww 0xfffffc30 0x00000007
 	sleep 10
 	# MC_FMR: flash mode (FWS=1,FMCN=60)
-	mww 0xffffff60 0x003c0100	
+	mww 0xffffff60 0x003c0100
 	sleep 100
 }
 
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
 
 #flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>]
 flash bank at91sam7 0 0 0 0 0 0 0 0 0 0 0 0 18432