X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=tcl%2Ftarget%2Fkl25z_hla.cfg;h=e4deac6157f98bcaa7e8acb6dcde3bf7d2ca6789;hp=3e561f11583dbf83988c46106ffa453fa1c15b92;hb=HEAD;hpb=46101959a6e8325549ff7e0165d27a32f6baec34

diff --git a/tcl/target/kl25z_hla.cfg b/tcl/target/kl25z_hla.cfg
deleted file mode 100644
index 3e561f1158..0000000000
--- a/tcl/target/kl25z_hla.cfg
+++ /dev/null
@@ -1,63 +0,0 @@
-# MKL25Z128VLK4
-# FreeScale Cortex-M0plus with 128kB Flash and 16kB Local On-Chip SRAM
-
-if { [info exists CHIPNAME] == 0 } {
-   set _CHIPNAME kl25z
-}
-
-if { [info exists CPUTAPID] == 0 } {
-   set _CPUTAPID 0x0BC11477
-}
-
-if { [info exists WORKAREASIZE] == 0 } {
-   set _WORKAREASIZE 0x3000
-}
-
-if { [info exists TRANSPORT] == 0 } {
-   set _TRANSPORT hla_swd
-}
-
-transport select $_TRANSPORT
-
-hla newtap $_CHIPNAME cpu -expected-id $_CPUTAPID
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME hla_target -chain-position $_TARGETNAME
-
-# It is important that "kinetis mdm check_security" is called for
-# 'examine-end' event and not 'eximine-start'. Calling it in 'examine-start'
-# causes "kinetis mdm check_security" to fail the first time openocd
-# calls it when it tries to connect after the CPU has been power-cycled.
-$_CHIPNAME.cpu configure -event examine-end {
-	kinetis mdm check_security
-}
-
-$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
-
-flash bank pflash kinetis 0x00000000 0x20000 0 4 $_TARGETNAME
-
-proc kl25z_enable_pll {} {
-	echo "KL25Z: Enabling PLL"
-	# SIM->CLKDIV1 = (uint32_t)0x00020000UL; /* Update system prescalers */
-	mww     0x40048044      0x00020000
-	# /* Switch to FEI Mode */
-	# MCG->C1 = (uint8_t)0x06U;
-	mwb 0x40064000  0x06
-	# MCG->C2 = (uint8_t)0x00U;
-	mwb 0x40064001  0x00
-	# /* MCG->C4: DMX32=0,DRST_DRS=1 */
-	# MCG->C4 = (uint8_t)((MCG->C4 & (uint8_t)~(uint8_t)0xC0U) | (uint8_t)0x20U);
-	mwb 0x40064003  0x37
-	#OSC0->CR = (uint8_t)0x80U;
-	mwb 0x40065000  0x80
-	# MCG->C5 = (uint8_t)0x00U;
-	mwb 0x40064004  0x00
-	# MCG->C6 = (uint8_t)0x00U;
-	mwb 0x40064005  0x00
-	sleep 100
-}
-
-$_TARGETNAME configure -event reset-init {
-	kl25z_enable_pll
-}
-