X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=tcl%2Fboard%2Fmini2440.cfg;h=874f829ab17b1fa54679adec01f5d0831bf8b7c3;hp=47bebc43dfab4ad0f40511e735f7b62ee3efc128;hb=146dfe32956de7d0fe1912a91c5268728ac0b7e0;hpb=4a2f4e34336dbb662a308e5a881edbba9f3657ec

diff --git a/tcl/board/mini2440.cfg b/tcl/board/mini2440.cfg
index 47bebc43df..874f829ab1 100644
--- a/tcl/board/mini2440.cfg
+++ b/tcl/board/mini2440.cfg
@@ -97,10 +97,9 @@ if { [info exists ENDIAN] } {
    set  _ENDIAN little
 }
 
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
-  # force an error till we get a good number
    set _CPUTAPID 0x0032409d
 }
 
@@ -112,7 +111,7 @@ target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME
 $_TARGETNAME configure -work-area-phys 0x40000000  -work-area-size 0x4000 -work-area-backup 1
 
 #reset configuration
-jtag_nsrst_delay 100
+adapter_nsrst_delay 100
 jtag_ntrst_delay 100
 reset_config trst_and_srst
 
@@ -121,7 +120,7 @@ reset_config trst_and_srst
 # IMPORTANT! See README at top of this file.
 #-------------------------------------------------------------------------
 
-    jtag_khz 12000
+    adapter_khz 12000
     jtag interface
 
 #-------------------------------------------------------------------------
@@ -141,7 +140,7 @@ reset_config trst_and_srst
 
     nand device s3c2440 0
 
-    jtag_nsrst_delay 100
+    adapter_nsrst_delay 100
     jtag_ntrst_delay 100
     reset_config trst_and_srst
     init
@@ -182,10 +181,10 @@ proc init_2440 { } {
     # usb clock are off 12mHz xtal
     #-----------------------------------------------
 
-    mww phys 0x4C000014 0x00000005 #  Clock Divider control Reg
-    mww phys 0x4C000000 0xFFFFFFFF #  LOCKTIME count register
-    mww phys 0x4C000008 0x00038022 #  UPPLCON  USB clock config Reg
-    mww phys 0x4C000004 0x0007F021 #  MPPLCON  Proc clock config Reg
+    mww phys 0x4C000014 0x00000005 ;#  Clock Divider control Reg
+    mww phys 0x4C000000 0xFFFFFFFF ;#  LOCKTIME count register
+    mww phys 0x4C000008 0x00038022 ;#  UPPLCON  USB clock config Reg
+    mww phys 0x4C000004 0x0007F021 ;#  MPPLCON  Proc clock config Reg
 
     #-----------------------------------------------
     # Configure Memory controller
@@ -193,45 +192,45 @@ proc init_2440 { } {
     # DRAM - 64MB - 32 bit bus, uses BANKCON6 BANKCON7
     #-----------------------------------------------
 
-    mww phys 0x48000000 0x22111112 #  BWSCON - Bank and Bus Width
-    mww phys 0x48000010 0x00001112 #  BANKCON4 - ?
-    mww phys 0x4800001c 0x00018009 #  BANKCON6 - DRAM
-    mww phys 0x48000020 0x00018009 #  BANKCON7 - DRAM
-    mww phys 0x48000024 0x008E04EB #  REFRESH  - DRAM
-    mww phys 0x48000028 0x000000B2 #  BANKSIZE - DRAM
-    mww phys 0x4800002C 0x00000030 #  MRSRB6 - DRAM
-    mww phys 0x48000030 0x00000030 #  MRSRB7 - DRAM
+    mww phys 0x48000000 0x22111112 ;#  BWSCON - Bank and Bus Width
+    mww phys 0x48000010 0x00001112 ;#  BANKCON4 - ?
+    mww phys 0x4800001c 0x00018009 ;#  BANKCON6 - DRAM
+    mww phys 0x48000020 0x00018009 ;#  BANKCON7 - DRAM
+    mww phys 0x48000024 0x008E04EB ;#  REFRESH  - DRAM
+    mww phys 0x48000028 0x000000B2 ;#  BANKSIZE - DRAM
+    mww phys 0x4800002C 0x00000030 ;#  MRSRB6 - DRAM
+    mww phys 0x48000030 0x00000030 ;#  MRSRB7 - DRAM
 
     #-----------------------------------------------
     # Now port configuration for enables for memory
     # and other stuff.
     #-----------------------------------------------
 
-    mww phys 0x56000000	0x007FFFFF #  GPACON
+    mww phys 0x56000000	0x007FFFFF ;#  GPACON
 
-    mww phys 0x56000010	0x00295559 #  GPBCON
-    mww phys 0x56000018	0x000003FF #  GPBUP (PULLUP ENABLE)
-    mww phys 0x56000014	0x000007C2 #  GPBDAT
+    mww phys 0x56000010	0x00295559 ;#  GPBCON
+    mww phys 0x56000018	0x000003FF ;#  GPBUP (PULLUP ENABLE)
+    mww phys 0x56000014	0x000007C2 ;#  GPBDAT
 
-    mww phys 0x56000020	0xAAAAA6AA #  GPCCON
-    mww phys 0x56000028	0x0000FFFF #  GPCUP
-    mww phys 0x56000024	0x00000020 #  GPCDAT
+    mww phys 0x56000020	0xAAAAA6AA ;#  GPCCON
+    mww phys 0x56000028	0x0000FFFF ;#  GPCUP
+    mww phys 0x56000024	0x00000020 ;#  GPCDAT
 
-    mww phys 0x56000030	0xAAAAAAAA #  GPDCON
-    mww phys 0x56000038	0x0000FFFF #  GPDUP
+    mww phys 0x56000030	0xAAAAAAAA ;#  GPDCON
+    mww phys 0x56000038	0x0000FFFF ;#  GPDUP
 
-    mww phys 0x56000040	0xAAAAAAAA #  GPECON
-    mww phys 0x56000048	0x0000FFFF #  GPEUP
+    mww phys 0x56000040	0xAAAAAAAA ;#  GPECON
+    mww phys 0x56000048	0x0000FFFF ;#  GPEUP
 
-    mww phys 0x56000050	0x00001555 #  GPFCON
-    mww phys 0x56000058	0x0000007F #  GPFUP
-    mww phys 0x56000054	0x00000000 #  GPFDAT
+    mww phys 0x56000050	0x00001555 ;#  GPFCON
+    mww phys 0x56000058	0x0000007F ;#  GPFUP
+    mww phys 0x56000054	0x00000000 ;#  GPFDAT
 
-    mww phys 0x56000060	0x00150114 #  GPGCON
-    mww phys 0x56000068	0x0000007F #  GPGUP
+    mww phys 0x56000060	0x00150114 ;#  GPGCON
+    mww phys 0x56000068	0x0000007F ;#  GPGUP
 
-    mww phys 0x56000070	0x0015AAAA #  GPHCON
-    mww phys 0x56000078	0x000003FF #  GPGUP
+    mww phys 0x56000070	0x0015AAAA ;#  GPHCON
+    mww phys 0x56000078	0x000003FF ;#  GPGUP
 
 }