Alan Carvalho de Assis <acassis@gmail.com> imx31pdk.cfg reset init event

[openocd.git] / testing / examples / ledtest-imx31pdk / gdbinit-imx31pdk

diff --git a/testing/examples/ledtest-imx31pdk/gdbinit-imx31pdk b/testing/examples/ledtest-imx31pdk/gdbinit-imx31pdk
index 336ddfba1da87ddb58a79f9e9c3568d567f63699..304a8d8992f011075e4ea82b0cdf87a0f0084d9f 100644 (file)
--- a/testing/examples/ledtest-imx31pdk/gdbinit-imx31pdk
+++ b/testing/examples/ledtest-imx31pdk/gdbinit-imx31pdk
@@ -1,136 +1,36 @@
-echo Setting up for the FreeScale iMX31 Board.\n\r
-# SETUP GDB :\r
-#\r
-# Common gdb setup for ARM CPUs\r
-set complaints 1\r
-set output-radix 10\r
-set input-radix 10\r
-set prompt (arm-gdb) \r
-set endian little\r
-dir .\r
-\r
-# Tell GDB to use 1024 bytes packes when downloading, this\r
-# reduces load image download times\r
-set remote memory-write-packet-size 1024\r
-set remote memory-write-packet-size fixed\r
-\r
-\r
-\r
-# DEFINE MACROS        :\r
-#\r
-# Create a "refresh" macro to update gdb's screens after the cpu\r
-# has been stopped by the other CPU or following an "monitor allstop" \r
-define refresh\r
-       monitor set hbreak\r
-       cont\r
-       monitor clear hbreak\r
-end\r
-\r
-\r
-# CONNECT TO TARGET :\r
-target remote 127.0.0.1:3333\r
-monitor reset run\r
-monitor reset halt\r
-\r
-# iMX31 PDK board initialization commands:\r
-\r
-#// init_ccm\r
-\r
-monitor mww 0x53FC0000 0x040\r
-monitor mww 0x53F80000 0x074B0B7D\r
-\r
-#//532-133-66.5\r
-#//monitor mww 0x53F80004 0xFF871D58\r
-#//monitor mww 0x53F80010 0x0033280C\r
-\r
-#// 399MHz - 26MHz input, PD=1,MFI=7, MFN=27, MFD=40\r
-monitor mww 0x53F80004 0xFF871D50\r
-monitor mww 0x53F80010 0x00271C1B\r
-\r
-#// 208-104-52\r
-#//monitor mww 0x53F80004 0xFF871D48\r
-#//monitor mww 0x53F80010 0x04002000\r
-\r
-\r
-#// Configure CPLD on CS5 \r
-monitor mww 0xb8002050 0x0000DCF6\r
-monitor mww 0xb8002054 0x444A4541\r
-monitor mww 0xb8002058 0x44443302\r
-\r
-#// Disable maximum drive strength for SDRAM/DDR lines by clearing DSE1 bits\r
-#// in SW_PAD_CTL registers\r
-\r
-#// SDCLK\r
-monitor mww 0x43FAC26C 0\r
- \r
-#// CAS\r
-monitor mww 0x43FAC270 0\r
- \r
-#// RAS\r
-monitor mww 0x43FAC274 0\r
- \r
-#// CS2 (CSD0)\r
-monitor mww 0x43FAC27C 0x1000\r
-    \r
-#// DQM3\r
-monitor mww 0x43FAC284 0\r
- \r
-#// DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC)\r
-monitor mww 0x43FAC288 0\r
-monitor mww 0x43FAC28C 0\r
-monitor mww 0x43FAC290 0\r
-monitor mww 0x43FAC294 0\r
-monitor mww 0x43FAC298 0\r
-monitor mww 0x43FAC29C 0\r
-monitor mww 0x43FAC2A0 0\r
-monitor mww 0x43FAC2A4 0\r
-monitor mww 0x43FAC2A8 0\r
-monitor mww 0x43FAC2AC 0\r
-monitor mww 0x43FAC2B0 0\r
-monitor mww 0x43FAC2B4 0\r
-monitor mww 0x43FAC2B8 0\r
-monitor mww 0x43FAC2BC 0\r
-monitor mww 0x43FAC2C0 0\r
-monitor mww 0x43FAC2C4 0\r
-monitor mww 0x43FAC2C8 0\r
-monitor mww 0x43FAC2CC 0\r
-monitor mww 0x43FAC2D0 0\r
-monitor mww 0x43FAC2D4 0\r
-monitor mww 0x43FAC2D8 0\r
-monitor mww 0x43FAC2DC 0\r
-\r
-#// Initialization script for 32 bit DDR on MX31 PDK \r
-monitor mww 0xB8001010 0x00000004\r
-monitor mww 0xB8001004 0x006ac73a\r
-monitor mww 0xB8001000 0x92100000\r
-monitor mww 0x80000f00 0x12344321\r
-monitor mww 0xB8001000 0xa2100000\r
-monitor mww 0x80000000 0x12344321\r
-monitor mww 0x80000000 0x12344321\r
-monitor mww 0xB8001000 0xb2100000\r
-#monitor char 0x80000033 0xda\r
-monitor mwb 0x80000033 0xda\r
-#monitor char 0x81000000 0xff\r
-monitor mwb 0x81000000 0xff\r
-monitor mww 0xB8001000 0x82226080\r
-monitor mww 0x80000000 0xDEADBEEF\r
-monitor mww 0xB8001010 0x0000000c\r
-\r
-#  LOAD IMAGE :\r
-#\r
-\r
-# Load the program executable called "u-boot"\r
-load test.elf\r
-\r
-# Load the symbols for the program.\r
-symbol-file test.elf\r
-\r
-# RUN TO MAIN :\r
-#\r
-# Set a breakpoint at main().\r
-#b reset\r
-b main\r
-\r
-# Run to the breakpoint.\r
-c\r
+echo Script to load ledtest on iMX31PDK.\n
+
+# Note: you need to startup openocd with "-f board/imx31pdk.cfg"
+# in order to it initialize RAM memory.
+
+# SETUP GDB :
+#
+# Common gdb setup for ARM CPUs
+set complaints 1
+set output-radix 10
+set input-radix 10
+set prompt (arm-gdb)
+set endian little
+dir .
+
+# CONNECT TO TARGET :
+target remote 127.0.0.1:3333
+
+#  LOAD IMAGE :
+#
+
+# Load the program executable called "u-boot"
+load test.elf
+
+# Load the symbols for the program.
+symbol-file test.elf
+
+# RUN TO MAIN :
+#
+# Set a breakpoint at main().
+#b reset
+b main
+
+# Run to the breakpoint.
+c