Fix spelling of ARM Cortex

[openocd.git] / tcl / target / omap3530.cfg

diff --git a/tcl/target/omap3530.cfg b/tcl/target/omap3530.cfg
index 0a83423c68243319c085a30e07c3a74b4457d8f1..c2929d1c4079ba8e7cb7a213514baa7f1e55ff7e 100644 (file)
--- a/tcl/target/omap3530.cfg
+++ b/tcl/target/omap3530.cfg
@@ -1,11 +1,11 @@
 # TI OMAP3530
-#  http://focus.ti.com/docs/prod/folders/print/omap3530.html
+# http://focus.ti.com/docs/prod/folders/print/omap3530.html
 # Other OMAP3 chips remove DSP and/or the OpenGL support
 
 if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
+   set _CHIPNAME $CHIPNAME
 } else {
-   set  _CHIPNAME omap3530
+   set _CHIPNAME omap3530
 }
 
 # ICEpick-C ... used to route Cortex, DSP, and more not shown here
@@ -15,7 +15,7 @@ source [find target/icepick.cfg]
 jtag newtap $_CHIPNAME dsp -irlen 38 -ircapture 0x25 -irmask 0x3f -disable
 
 # Subsidiary TAP: CoreSight Debug Access Port (DAP)
-if { [info exists DAP_TAPID ] } {
+if { [info exists DAP_TAPID] } {
    set _DAP_TAPID $DAP_TAPID
 } else {
    set _DAP_TAPID 0x0b6d602f
@@ -26,7 +26,7 @@ jtag configure $_CHIPNAME.dap -event tap-enable \
        "icepick_c_tapenable $_CHIPNAME.jrc 3"
 
 # Primary TAP: ICEpick-C (JTAG route controller) and boundary scan
-if { [info exists JRC_TAPID ] } {
+if { [info exists JRC_TAPID] } {
    set _JRC_TAPID $JRC_TAPID
 } else {
    set _JRC_TAPID 0x0b7ae02f
@@ -34,9 +34,9 @@ if { [info exists JRC_TAPID ] } {
 jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f \
        -expected-id $_JRC_TAPID
 
-# GDB target:  Cortex-A8, using DAP
+# GDB target: Cortex-A8, using DAP
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_a8 -chain-position $_CHIPNAME.dap
+target create $_TARGETNAME cortex_a -chain-position $_CHIPNAME.dap
 
 # SRAM: 64K at 0x4020.0000; use the first 16K
 $_TARGETNAME configure -work-area-phys 0x40200000 -work-area-size 0x4000
@@ -53,22 +53,22 @@ jtag configure $_CHIPNAME.jrc -event post-reset "runtest 100"
 jtag configure $_CHIPNAME.jrc -event setup "jtag tapenable $_CHIPNAME.dap"
 
 proc omap3_dbginit {target} {
-     # General Cortex A8 debug initialisation
-     cortex_a8 dbginit
+     # General Cortex-A8 debug initialisation
+     cortex_a dbginit
      # Enable DBGU signal for OMAP353x
-     $target mww 0x5401d030 0x00002000
+     $target mww phys 0x5401d030 0x00002000
 }
 
 # be absolutely certain the JTAG clock will work with the worst-case
 # 16.8MHz/2 = 8.4MHz core clock, even before a bootloader kicks in.
 # OK to speed up *after* PLL and clock tree setup.
-jtag_rclk 1000
-$_TARGETNAME configure -event "reset-start" { jtag_rclk 1000 }
+adapter_khz 1000
+$_TARGETNAME configure -event "reset-start" { adapter_khz 1000 }
 
-# REVISIT This assumes that SRST is unavailable, so we must assert reset
+# Assume SRST is unavailable (e.g. TI-14 JTAG), so we must assert reset
 # ourselves using PRM_RSTCTRL.  RST_GS (2) is a warm reset, like ICEpick
 # would issue.  RST_DPLL3 (4) is a cold reset.
 set PRM_RSTCTRL 0x48307250
-$_TARGETNAME configure -event reset-assert-pre "$_TARGETNAME mww $PRM_RSTCTRL 2"
+$_TARGETNAME configure -event reset-assert "$_TARGETNAME mww $PRM_RSTCTRL 2"
 
 $_TARGETNAME configure -event reset-assert-post "omap3_dbginit $_TARGETNAME"