jtag: linuxgpiod: drop extra parenthesis

[openocd.git] / tcl / target / lpc2478.cfg

diff --git a/tcl/target/lpc2478.cfg b/tcl/target/lpc2478.cfg
index 3b14c87d426971d076585bcba883c7e40b5a9f92..e4fd49d43b5bb88558a756056ff911de3e04aeb6 100644 (file)
--- a/tcl/target/lpc2478.cfg
+++ b/tcl/target/lpc2478.cfg
@@ -1,46 +1,23 @@
-# NXP LPC2478 ARM7TDMI-S with 512kB Flash and 64kB Local On-Chip SRAM (98kB total), clocked with 4MHz internal RC oscillator
+# SPDX-License-Identifier: GPL-2.0-or-later
 
-if { [info exists CHIPNAME] } {
-       set  _CHIPNAME $CHIPNAME
-} else {
-       set  _CHIPNAME lpc2478
-}
-
-if { [info exists CPUTAPID ] } {
-       set _CPUTAPID $CPUTAPID
-} else {
-       set _CPUTAPID 0x4f1f0f0f
-}
-
-if { [info exists CCLK ] } {
-       set _CCLK $CCLK
-} else {
-    error "You must specify the CCLK that will be used for flash programming!"
-}
+# NXP LPC2478 ARM7TDMI-S with 512kB flash (8kB used by bootloader) and 98kB SRAM (16kB for ETH, 16kB for DMA, 2kB for RTC), clocked with 4MHz internal oscillator
 
-#delays on reset lines
-adapter_nsrst_delay 100
-jtag_ntrst_delay 100
+source [find target/lpc2xxx.cfg]
 
-reset_config trst_and_srst
+# parameters:
+# - core_freq_khz - frequency of core in kHz during flashing, usually equal to connected crystal or internal oscillator, e.g. 12000
+# - adapter_freq_khz - frequency of debug adapter in kHz, should be 8x slower than core_freq_khz, e.g. 1000
 
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm7tdmi -chain-position $_TARGETNAME
-
-# LPC2478 has 64kB of SRAM on its main system bus (so-called Local On-Chip SRAM)
-$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x10000 -work-area-backup 0
-
-$_TARGETNAME configure -event reset-init {
-       # Force target into ARM state
-       arm core_state arm
-       # Do not remap 0x0000-0x0020 to anything but the Flash
-       mwb 0xE01FC040 0x01
+proc setup_lpc2478 {core_freq_khz adapter_freq_khz} {
+       # 504kB flash and 64kB SRAM
+       # setup_lpc2xxx <chip_name> <cputapid> <flash_size> <flash_variant> <workarea_size> <core_freq_khz> <adapter_freq_khz>
+       setup_lpc2xxx lpc2478 0x4f1f0f0f 0x7e000 lpc2000_v2 0x10000 $core_freq_khz $adapter_freq_khz
 }
 
-# LPC2378 has 512kB of FLASH, but upper 8kB are occupied by bootloader.
-# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME lpc2000 0x0 0x7E000 0 0 $_TARGETNAME lpc2000_v2 $_CCLK calc_checksum
+proc init_targets {} {
+       # default to core clocked with 4MHz internal oscillator
+       echo "Warning - assuming default core clock 4MHz! Flashing may fail if actual core clock is different."
 
+       # setup_lpc2478 <core_freq_khz> <adapter_freq_khz>
+       setup_lpc2478 4000 500
+}