cfg: add initial Atmel xplained kit support

[openocd.git] / tcl / target / at91sam4XXX.cfg

diff --git a/tcl/target/at91sam4XXX.cfg b/tcl/target/at91sam4XXX.cfg
index 24b3deb8e6308bd271490b77a56120aed47dab4d..cc2941a8198f7550753ffb36676d8304fbc07daa 100644 (file)
--- a/tcl/target/at91sam4XXX.cfg
+++ b/tcl/target/at91sam4XXX.cfg
@@ -1,6 +1,12 @@
+#
 # script for ATMEL sam4, a CORTEX-M4 chip
 #
 
+#
+# sam4 devices can support both JTAG and SWD transports.
+#
+source [find target/swj-dp.tcl]
+
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
 } else {
@@ -13,17 +19,13 @@ if { [info exists ENDIAN] } {
    set _ENDIAN little
 }
 
-# JTAG speed should be <= F_CPU/6. F_CPU after reset is 4 MHz, so use F_JTAG = 0.5MHz
-#
-# Since we may be running of an RC oscilator, we crank down the speed a
-# bit more to be on the safe side. Perhaps superstition, but if are
-# running off a crystal, we can run closer to the limit. Note
-# that there can be a pretty wide band where things are more or less stable.
-
-adapter_khz 500
-
-adapter_nsrst_delay 100
-jtag_ntrst_delay 100
+# Work-area is a space in RAM used for flash programming
+# By default use 64kB
+if { [info exists WORKAREASIZE] } {
+   set _WORKAREASIZE $WORKAREASIZE
+} else {
+   set _WORKAREASIZE 0x4000
+}
 
 #jtag scan chain
 if { [info exists CPUTAPID] } {
@@ -32,18 +34,32 @@ if { [info exists CPUTAPID] } {
    set _CPUTAPID 0x4ba00477
 }
 
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
 set _TARGETNAME $_CHIPNAME.cpu
 target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
 
 # 16K is plenty, the smallest chip has this much
-$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 $_TARGETNAME configure -event gdb-flash-erase-start {
     halt
 }
 
+# JTAG speed should be <= F_CPU/6. F_CPU after reset is 4 MHz, so use F_JTAG = 0.5MHz
+#
+# Since we may be running of an RC oscilator, we crank down the speed a
+# bit more to be on the safe side. Perhaps superstition, but if are
+# running off a crystal, we can run closer to the limit. Note
+# that there can be a pretty wide band where things are more or less stable.
+
+adapter_khz 500
+
+adapter_nsrst_delay 100
+if {$using_jtag} {
+ jtag_ntrst_delay 100
+}
+
 # if srst is not fitted use SYSRESETREQ to
 # perform a soft reset
 cortex_m reset_config sysresetreq