zy1000: drop the code, deprecated in v0.10.0

[openocd.git] / tcl / board / zy1000.cfg

diff --git a/tcl/board/zy1000.cfg b/tcl/board/zy1000.cfg
deleted file mode 100644 (file)
index e0d1ccf..0000000
--- a/tcl/board/zy1000.cfg
+++ /dev/null
@@ -1,117 +0,0 @@
-#Script for ZY1000
-
-#Atmel ties SRST & TRST together, at which point it makes
-#no sense to use TRST, but use TMS instead.
-#
-#The annoying thing with tying SRST & TRST together is that
-#there is no way to halt the CPU *before and during* the
-#SRST reset, which means that the CPU will run a number
-#of cycles before it can be halted(as much as milliseconds).
-reset_config srst_only srst_pulls_trst
-
-
-if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
-} else {
-   set  _CHIPNAME zy1000
-}
-
-if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
-} else {
-   set  _ENDIAN little
-}
-
-
-#jtag scan chain
-if { [info exists CPUTAPID] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-   set _CPUTAPID 0x1f0f0f0f
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME
-
-# at CPU CLK <32kHz this must be disabled
-arm7_9 fast_memory_access enable
-arm7_9 dcc_downloads enable
-
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME cfi 0x01000000 0x200000 2 2 $_TARGETNAME
-
-$_TARGETNAME configure -event reset-init {
-       # Set up chip selects & timings
-       mww 0xFFE00000 0x0100273D
-       mww 0xFFE00004 0x08002125
-       mww 0xFFEe0008 0x02002125
-       mww 0xFFE0000c 0x03002125
-       mww 0xFFE00010 0x40000000
-       mww 0xFFE00014 0x50000000
-       mww 0xFFE00018 0x60000000
-       mww 0xFFE0001c 0x70000000
-       mww 0xFFE00020 0x00000001
-       mww 0xFFE00024 0x00000000
-
-       # remap
-       mww 0xFFFFF124 0xFFFFFFFF
-       mww 0xffff0010 0x100
-       mww 0xffff0034 0x100
-
-       #disable 16x5x UART interrupts
-       mww 0x08020004 0
-}
-
-$_TARGETNAME configure -event gdb-attach {
-       # Without this gdb-attach will first time as probe will fail
-       reset init
-}
-
-# required for usable performance. Used for lots of
-# other things than flash programming.
-$_TARGETNAME configure -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0
-
-adapter speed 16000
-
-
-proc production_info {} {
-       return "Serial number is official MAC number. Format XXXXXXXXXXXX"
-}
-
-# There is no return value from this procedure. If it is
-# successful it does not throw an exception
-#
-# Progress messages are output via puts
-proc production {firmwarefile serialnumber} {
-       if {[string length $serialnumber]!=12} {
-               echo "Invalid serial number"
-               return
-       }
-
-       echo "Power cycling target"
-       power off
-       sleep 3000
-       power on
-       sleep 1000
-       reset init
-       flash write_image erase $firmwarefile 0x1000000 bin
-       verify_image $firmwarefile 0x1000000 bin
-
-       # Big endian... weee!!!!
-       echo "Setting MAC number to $serialnumber"
-       flash fillw [expr 0x1030000-0x8] "0x[string range $serialnumber 2 3][string range $serialnumber 0 1]0000" 1
-       flash fillw [expr 0x1030000-0x4] "0x[string range $serialnumber 10 11][string range $serialnumber 8 9][string range $serialnumber 6 7][string range $serialnumber 4 5]" 1
-       echo "Production successful"
-}
-
-
-proc production_test {} {
-       power on
-       sleep 1000
-       target_request debugmsgs enable
-       reset run
-       sleep 25000
-       target_request debugmsgs disable
-       return "See IP address above..."
-}