* Copyright (C) 2008 by Spencer Oliver *
* spen@spen-soft.co.uk *
* *
- * Copyright (C) 2009 by Oyvind Harboe *
+ * Copyright (C) 2009-2010 by Oyvind Harboe *
* oyvind.harboe@zylin.com *
* *
* Copyright (C) 2009-2010 by David Brownell *
* is used to access memory mapped resources and is called a MEM-AP. Also a
* JTAG-AP is also defined, bridging to JTAG resources; those are uncommon.
*
- * @todo Remove modality (queued/nonqueued, via DAP trans_mode) from all
- * procedure interfaces. Modal programming interfaces are very error prone.
- * Procedures should be either queued, or synchronous. Otherwise input
- * and output constraints are context-sensitive, and it's hard to know
- * what a block of code will do just by reading it.
+ * This programming interface allows DAP pipelined operations through a
+ * transaction queue. This primarily affects AP operations (such as using
+ * a MEM-AP to access memory or registers). If the current transaction has
+ * not finished by the time the next one must begin, and the ORUNDETECT bit
+ * is set in the DP_CTRL_STAT register, the SSTICKYORUN status is set and
+ * further AP operations will fail. There are two basic methods to avoid
+ * such overrun errors. One involves polling for status instead of using
+ * transaction piplining. The other involves adding delays to ensure the
+ * AP has enough time to complete one operation before starting the next
+ * one. (For JTAG these delays are controlled by memaccess_tck.)
*/
/*
#include "config.h"
#endif
+#include "jtag/interface.h"
+#include "arm.h"
#include "arm_adi_v5.h"
#include <helper/time_support.h>
-/*
- * Transaction Mode:
- * swjdp->trans_mode = TRANS_MODE_COMPOSITE;
- * Uses Overrun checking mode and does not do actual JTAG send/receive or transaction
- * result checking until swjdp_end_transaction()
- * This must be done before using or deallocating any return variables.
- * swjdp->trans_mode == TRANS_MODE_ATOMIC
- * All reads and writes to the AHB bus are checked for valid completion, and return values
- * are immediatley available.
-*/
-
-
/* ARM ADI Specification requires at least 10 bits used for TAR autoincrement */
/*
return (tar_autoincr_block - ((tar_autoincr_block - 1) & address)) >> 2;
}
-/***************************************************************************
- * *
- * DPACC and APACC scanchain access through JTAG-DP *
- * *
-***************************************************************************/
-
-/**
- * Scan DPACC or APACC using target ordered uint8_t buffers. No endianness
- * conversions are performed. See section 4.4.3 of the ADIv5 spec, which
- * discusses operations which access these registers.
- *
- * Note that only one scan is performed. If RnW is set, a separate scan
- * will be needed to collect the data which was read; the "invalue" collects
- * the posted result of a preceding operation, not the current one.
- *
- * @param swjdp the DAP
- * @param instr JTAG_DP_APACC (AP access) or JTAG_DP_DPACC (DP access)
- * @param reg_addr two significant bits; A[3:2]; for APACC access, the
- * SELECT register has more addressing bits.
- * @param RnW false iff outvalue will be written to the DP or AP
- * @param outvalue points to a 32-bit (little-endian) integer
- * @param invalue NULL, or points to a 32-bit (little-endian) integer
- * @param ack points to where the three bit JTAG_ACK_* code will be stored
- */
-static int adi_jtag_dp_scan(struct swjdp_common *swjdp,
- uint8_t instr, uint8_t reg_addr, uint8_t RnW,
- uint8_t *outvalue, uint8_t *invalue, uint8_t *ack)
-{
- struct arm_jtag *jtag_info = swjdp->jtag_info;
- struct scan_field fields[2];
- uint8_t out_addr_buf;
-
- jtag_set_end_state(TAP_IDLE);
- arm_jtag_set_instr(jtag_info, instr, NULL);
-
- /* Add specified number of tck clocks before accessing memory bus */
-
- /* REVISIT these TCK cycles should be *AFTER* updating APACC, since
- * they provide more time for the (MEM) AP to complete the read ...
- * See "Minimum Response Time" for JTAG-DP, in the ADIv5 spec.
- */
- if ((instr == JTAG_DP_APACC)
- && ((reg_addr == AP_REG_DRW)
- || ((reg_addr & 0xF0) == AP_REG_BD0))
- && (swjdp->memaccess_tck != 0))
- jtag_add_runtest(swjdp->memaccess_tck, jtag_set_end_state(TAP_IDLE));
-
- /* Scan out a read or write operation using some DP or AP register.
- * For APACC access with any sticky error flag set, this is discarded.
- */
- fields[0].tap = jtag_info->tap;
- fields[0].num_bits = 3;
- buf_set_u32(&out_addr_buf, 0, 3, ((reg_addr >> 1) & 0x6) | (RnW & 0x1));
- fields[0].out_value = &out_addr_buf;
- fields[0].in_value = ack;
-
- /* NOTE: if we receive JTAG_ACK_WAIT, the previous operation did not
- * complete; data we write is discarded, data we read is unpredictable.
- * When overrun detect is active, STICKYORUN is set.
- */
-
- fields[1].tap = jtag_info->tap;
- fields[1].num_bits = 32;
- fields[1].out_value = outvalue;
- fields[1].in_value = invalue;
-
- jtag_add_dr_scan(2, fields, jtag_get_end_state());
-
- return jtag_get_error();
-}
-
-/**
- * Scan DPACC or APACC out and in from host ordered uint32_t buffers.
- * This is exactly like adi_jtag_dp_scan(), except that endianness
- * conversions are performed (so the types of invalue and outvalue
- * must be different).
- */
-static int adi_jtag_dp_scan_u32(struct swjdp_common *swjdp,
- uint8_t instr, uint8_t reg_addr, uint8_t RnW,
- uint32_t outvalue, uint32_t *invalue, uint8_t *ack)
-{
- uint8_t out_value_buf[4];
- int retval;
-
- buf_set_u32(out_value_buf, 0, 32, outvalue);
-
- retval = adi_jtag_dp_scan(swjdp, instr, reg_addr, RnW,
- out_value_buf, (uint8_t *)invalue, ack);
- if (retval != ERROR_OK)
- return retval;
-
- if (invalue)
- jtag_add_callback(arm_le_to_h_u32,
- (jtag_callback_data_t) invalue);
-
- return retval;
-}
-
-/**
- * Utility to write AP registers.
- */
-static int ap_write_check(struct swjdp_common *dap,
- uint8_t reg_addr, uint8_t *outvalue)
-{
- adi_jtag_dp_scan(dap, JTAG_DP_APACC, reg_addr, DPAP_WRITE,
- outvalue, NULL, NULL);
-
- /* REVISIT except in dap_setup_accessport() almost all call paths
- * set up COMPOSITE. Probably worth just inlining the scan...
- */
-
- /* In TRANS_MODE_ATOMIC all JTAG_DP_APACC transactions wait for
- * ack = OK/FAULT and the check CTRL_STAT
- */
- if (dap->trans_mode == TRANS_MODE_ATOMIC)
- return jtagdp_transaction_endcheck(dap);
-
- return ERROR_OK;
-}
-
-static int scan_inout_check_u32(struct swjdp_common *swjdp,
- uint8_t instr, uint8_t reg_addr, uint8_t RnW,
- uint32_t outvalue, uint32_t *invalue)
-{
- /* Issue the read or write */
- adi_jtag_dp_scan_u32(swjdp, instr, reg_addr, RnW, outvalue, NULL, NULL);
-
- /* For reads, collect posted value; RDBUFF has no other effect.
- * Assumes read gets acked with OK/FAULT, and CTRL_STAT says "OK".
- */
- if ((RnW == DPAP_READ) && (invalue != NULL))
- adi_jtag_dp_scan_u32(swjdp, JTAG_DP_DPACC,
- DP_RDBUFF, DPAP_READ, 0, invalue, &swjdp->ack);
-
- /* In TRANS_MODE_ATOMIC all JTAG_DP_APACC transactions wait for
- * ack = OK/FAULT and then check CTRL_STAT
- */
- if ((instr == JTAG_DP_APACC)
- && (swjdp->trans_mode == TRANS_MODE_ATOMIC))
- return jtagdp_transaction_endcheck(swjdp);
-
- return ERROR_OK;
-}
-
-int jtagdp_transaction_endcheck(struct swjdp_common *swjdp)
-{
- int retval;
- uint32_t ctrlstat;
-
- /* too expensive to call keep_alive() here */
-
-#if 0
- /* Danger!!!! BROKEN!!!! */
- scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
- DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
- /* Danger!!!! BROKEN!!!! Why will jtag_execute_queue() fail here????
- R956 introduced the check on return value here and now Michael Schwingen reports
- that this code no longer works....
-
- https://lists.berlios.de/pipermail/openocd-development/2008-September/003107.html
- */
- if ((retval = jtag_execute_queue()) != ERROR_OK)
- {
- LOG_ERROR("BUG: Why does this fail the first time????");
- }
- /* Why??? second time it works??? */
-#endif
-
- /* Post CTRL/STAT read; discard any previous posted read value
- * but collect its ACK status.
- */
- scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
- DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
- return retval;
-
- swjdp->ack = swjdp->ack & 0x7;
-
- /* common code path avoids calling timeval_ms() */
- if (swjdp->ack != JTAG_ACK_OK_FAULT)
- {
- long long then = timeval_ms();
-
- while (swjdp->ack != JTAG_ACK_OK_FAULT)
- {
- if (swjdp->ack == JTAG_ACK_WAIT)
- {
- if ((timeval_ms()-then) > 1000)
- {
- /* NOTE: this would be a good spot
- * to use JTAG_DP_ABORT.
- */
- LOG_WARNING("Timeout (1000ms) waiting "
- "for ACK=OK/FAULT "
- "in JTAG-DP transaction");
- return ERROR_JTAG_DEVICE_ERROR;
- }
- }
- else
- {
- LOG_WARNING("Invalid ACK %#x "
- "in JTAG-DP transaction",
- swjdp->ack);
- return ERROR_JTAG_DEVICE_ERROR;
- }
-
- scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
- DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
- return retval;
- swjdp->ack = swjdp->ack & 0x7;
- }
- }
-
- /* REVISIT also STICKYCMP, for pushed comparisons (nyet used) */
-
- /* Check for STICKYERR and STICKYORUN */
- if (ctrlstat & (SSTICKYORUN | SSTICKYERR))
- {
- LOG_DEBUG("jtag-dp: CTRL/STAT error, 0x%" PRIx32, ctrlstat);
- /* Check power to debug regions */
- if ((ctrlstat & 0xf0000000) != 0xf0000000)
- ahbap_debugport_init(swjdp);
- else
- {
- uint32_t mem_ap_csw, mem_ap_tar;
-
- /* Maybe print information about last intended
- * MEM-AP access; but not if autoincrementing.
- * *Real* CSW and TAR values are always shown.
- */
- if (swjdp->ap_tar_value != (uint32_t) -1)
- LOG_DEBUG("MEM-AP Cached values: "
- "ap_bank 0x%" PRIx32
- ", ap_csw 0x%" PRIx32
- ", ap_tar 0x%" PRIx32,
- swjdp->ap_bank_value,
- swjdp->ap_csw_value,
- swjdp->ap_tar_value);
-
- if (ctrlstat & SSTICKYORUN)
- LOG_ERROR("JTAG-DP OVERRUN - check clock, "
- "memaccess, or reduce jtag speed");
-
- if (ctrlstat & SSTICKYERR)
- LOG_ERROR("JTAG-DP STICKY ERROR");
-
- /* Clear Sticky Error Bits */
- scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
- DP_CTRL_STAT, DPAP_WRITE,
- swjdp->dp_ctrl_stat | SSTICKYORUN
- | SSTICKYERR, NULL);
- scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
- DP_CTRL_STAT, DPAP_READ, 0, &ctrlstat);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
- return retval;
-
- LOG_DEBUG("jtag-dp: CTRL/STAT 0x%" PRIx32, ctrlstat);
-
- dap_ap_read_reg_u32(swjdp, AP_REG_CSW, &mem_ap_csw);
- dap_ap_read_reg_u32(swjdp, AP_REG_TAR, &mem_ap_tar);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
- return retval;
- LOG_ERROR("MEM_AP_CSW 0x%" PRIx32 ", MEM_AP_TAR 0x%"
- PRIx32, mem_ap_csw, mem_ap_tar);
-
- }
- if ((retval = jtag_execute_queue()) != ERROR_OK)
- return retval;
- return ERROR_JTAG_DEVICE_ERROR;
- }
-
- return ERROR_OK;
-}
-
/***************************************************************************
* *
* DP and MEM-AP register access through APACC and DPACC *
* *
***************************************************************************/
-static int dap_dp_write_reg(struct swjdp_common *swjdp,
- uint32_t value, uint8_t reg_addr)
-{
- return scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
- reg_addr, DPAP_WRITE, value, NULL);
-}
-
-static int dap_dp_read_reg(struct swjdp_common *swjdp,
- uint32_t *value, uint8_t reg_addr)
-{
- return scan_inout_check_u32(swjdp, JTAG_DP_DPACC,
- reg_addr, DPAP_READ, 0, value);
-}
-
/**
* Select one of the APs connected to the specified DAP. The
* selection is implicitly used with future AP transactions.
* This is a NOP if the specified AP is already selected.
*
- * @param swjdp The DAP
+ * @param dap The DAP
* @param apsel Number of the AP to (implicitly) use with further
* transactions. This normally identifies a MEM-AP.
*/
-void dap_ap_select(struct swjdp_common *swjdp,uint8_t apsel)
+void dap_ap_select(struct adiv5_dap *dap, uint8_t ap)
{
- uint32_t select = (apsel << 24) & 0xFF000000;
+ uint32_t new_ap = (ap << 24) & 0xFF000000;
- if (select != swjdp->apsel)
- {
- swjdp->apsel = select;
+ if (new_ap != dap->ap_current) {
+ dap->ap_current = new_ap;
/* Switching AP invalidates cached values.
* Values MUST BE UPDATED BEFORE AP ACCESS.
*/
- swjdp->ap_bank_value = -1;
- swjdp->ap_csw_value = -1;
- swjdp->ap_tar_value = -1;
+ dap->ap_bank_value = -1;
+ dap->ap_csw_value = -1;
+ dap->ap_tar_value = -1;
}
}
-/** Select the AP register bank matching bits 7:4 of ap_reg. */
-static int dap_ap_bankselect(struct swjdp_common *swjdp, uint32_t ap_reg)
-{
- uint32_t select = (ap_reg & 0x000000F0);
-
- if (select != swjdp->ap_bank_value)
- {
- swjdp->ap_bank_value = select;
- select |= swjdp->apsel;
- return dap_dp_write_reg(swjdp, select, DP_SELECT);
- } else
- return ERROR_OK;
-}
-
-static int dap_ap_write_reg(struct swjdp_common *swjdp,
- uint32_t reg_addr, uint8_t *out_value_buf)
-{
- int retval;
-
- retval = dap_ap_bankselect(swjdp, reg_addr);
- if (retval != ERROR_OK)
- return retval;
-
- return ap_write_check(swjdp, reg_addr, out_value_buf);
-}
-
-/**
- * Write an AP register value.
- * This is synchronous iff the mode is set to ATOMIC, in which
- * case any queued transactions are flushed.
- *
- * @param swjdp The DAP whose currently selected AP will be written.
- * @param reg_addr Eight bit AP register address.
- * @param value Word to be written at reg_addr
- *
- * @return In synchronous mode: ERROR_OK for success, and the register holds
- * the specified value; else a fault code. In asynchronous mode, a status
- * code reflecting whether the transaction was properly queued.
- */
-int dap_ap_write_reg_u32(struct swjdp_common *swjdp,
- uint32_t reg_addr, uint32_t value)
-{
- uint8_t out_value_buf[4];
-
- buf_set_u32(out_value_buf, 0, 32, value);
- return dap_ap_write_reg(swjdp,
- reg_addr, out_value_buf);
-}
-
-/**
- * Read an AP register value.
- * This is synchronous iff the mode is set to ATOMIC, in which
- * case any queued transactions are flushed.
- *
- * @param swjdp The DAP whose currently selected AP will be read.
- * @param reg_addr Eight bit AP register address.
- * @param value Points to where the 32-bit (little-endian) word will be stored.
- *
- * @return In synchronous mode: ERROR_OK for success, and *value holds
- * the specified value; else a fault code. In asynchronous mode, a status
- * code reflecting whether the transaction was properly queued.
- */
-int dap_ap_read_reg_u32(struct swjdp_common *swjdp,
- uint32_t reg_addr, uint32_t *value)
-{
- int retval;
-
- retval = dap_ap_bankselect(swjdp, reg_addr);
- if (retval != ERROR_OK)
- return retval;
-
- return scan_inout_check_u32(swjdp, JTAG_DP_APACC, reg_addr,
- DPAP_READ, 0, value);
-}
-
/**
- * Set up transfer parameters for the currently selected MEM-AP.
- * This is synchronous iff the mode is set to ATOMIC, in which
- * case any queued transactions are flushed.
+ * Queue transactions setting up transfer parameters for the
+ * currently selected MEM-AP.
*
* Subsequent transfers using registers like AP_REG_DRW or AP_REG_BD2
* initiate data reads or writes using memory or peripheral addresses.
*
* @todo Rename to reflect it being specifically a MEM-AP function.
*
- * @param swjdp The DAP connected to the MEM-AP.
+ * @param dap The DAP connected to the MEM-AP.
* @param csw MEM-AP Control/Status Word (CSW) register to assign. If this
* matches the cached value, the register is not changed.
* @param tar MEM-AP Transfer Address Register (TAR) to assign. If this
* matches the cached address, the register is not changed.
*
- * @return In synchronous mode: ERROR_OK for success, and the AP is set
- * up as requested else a fault code. In asynchronous mode, a status
- * code reflecting whether the transaction was properly queued.
+ * @return ERROR_OK if the transaction was properly queued, else a fault code.
*/
-int dap_setup_accessport(struct swjdp_common *swjdp, uint32_t csw, uint32_t tar)
+int dap_setup_accessport(struct adiv5_dap *dap, uint32_t csw, uint32_t tar)
{
int retval;
csw = csw | CSW_DBGSWENABLE | CSW_MASTER_DEBUG | CSW_HPROT;
- if (csw != swjdp->ap_csw_value)
- {
+ if (csw != dap->ap_csw_value) {
/* LOG_DEBUG("DAP: Set CSW %x",csw); */
- retval = dap_ap_write_reg_u32(swjdp, AP_REG_CSW, csw);
+ retval = dap_queue_ap_write(dap, AP_REG_CSW, csw);
if (retval != ERROR_OK)
return retval;
- swjdp->ap_csw_value = csw;
+ dap->ap_csw_value = csw;
}
- if (tar != swjdp->ap_tar_value)
- {
+ if (tar != dap->ap_tar_value) {
/* LOG_DEBUG("DAP: Set TAR %x",tar); */
- retval = dap_ap_write_reg_u32(swjdp, AP_REG_TAR, tar);
+ retval = dap_queue_ap_write(dap, AP_REG_TAR, tar);
if (retval != ERROR_OK)
return retval;
- swjdp->ap_tar_value = tar;
+ dap->ap_tar_value = tar;
}
/* Disable TAR cache when autoincrementing */
if (csw & CSW_ADDRINC_MASK)
- swjdp->ap_tar_value = -1;
+ dap->ap_tar_value = -1;
return ERROR_OK;
}
/**
* Asynchronous (queued) read of a word from memory or a system register.
*
- * @param swjdp The DAP connected to the MEM-AP performing the read.
+ * @param dap The DAP connected to the MEM-AP performing the read.
* @param address Address of the 32-bit word to read; it must be
* readable by the currently selected MEM-AP.
* @param value points to where the word will be stored when the
*
* @return ERROR_OK for success. Otherwise a fault code.
*/
-int mem_ap_read_u32(struct swjdp_common *swjdp, uint32_t address,
+int mem_ap_read_u32(struct adiv5_dap *dap, uint32_t address,
uint32_t *value)
{
int retval;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
/* Use banked addressing (REG_BDx) to avoid some link traffic
* (updating TAR) when reading several consecutive addresses.
*/
- retval = dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_OFF,
+ retval = dap_setup_accessport(dap, CSW_32BIT | CSW_ADDRINC_OFF,
address & 0xFFFFFFF0);
if (retval != ERROR_OK)
return retval;
- return dap_ap_read_reg_u32(swjdp, AP_REG_BD0 | (address & 0xC), value);
+ return dap_queue_ap_read(dap, AP_REG_BD0 | (address & 0xC), value);
}
/**
* Synchronous read of a word from memory or a system register.
* As a side effect, this flushes any queued transactions.
*
- * @param swjdp The DAP connected to the MEM-AP performing the read.
+ * @param dap The DAP connected to the MEM-AP performing the read.
* @param address Address of the 32-bit word to read; it must be
* readable by the currently selected MEM-AP.
* @param value points to where the result will be stored.
* @return ERROR_OK for success; *value holds the result.
* Otherwise a fault code.
*/
-int mem_ap_read_atomic_u32(struct swjdp_common *swjdp, uint32_t address,
+int mem_ap_read_atomic_u32(struct adiv5_dap *dap, uint32_t address,
uint32_t *value)
{
int retval;
- retval = mem_ap_read_u32(swjdp, address, value);
+ retval = mem_ap_read_u32(dap, address, value);
if (retval != ERROR_OK)
return retval;
- return jtagdp_transaction_endcheck(swjdp);
+ return dap_run(dap);
}
/**
* Asynchronous (queued) write of a word to memory or a system register.
*
- * @param swjdp The DAP connected to the MEM-AP.
+ * @param dap The DAP connected to the MEM-AP.
* @param address Address to be written; it must be writable by
* the currently selected MEM-AP.
* @param value Word that will be written to the address when transaction
*
* @return ERROR_OK for success. Otherwise a fault code.
*/
-int mem_ap_write_u32(struct swjdp_common *swjdp, uint32_t address,
+int mem_ap_write_u32(struct adiv5_dap *dap, uint32_t address,
uint32_t value)
{
int retval;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
/* Use banked addressing (REG_BDx) to avoid some link traffic
* (updating TAR) when writing several consecutive addresses.
*/
- retval = dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_OFF,
+ retval = dap_setup_accessport(dap, CSW_32BIT | CSW_ADDRINC_OFF,
address & 0xFFFFFFF0);
if (retval != ERROR_OK)
return retval;
- return dap_ap_write_reg_u32(swjdp, AP_REG_BD0 | (address & 0xC),
+ return dap_queue_ap_write(dap, AP_REG_BD0 | (address & 0xC),
value);
}
* Synchronous write of a word to memory or a system register.
* As a side effect, this flushes any queued transactions.
*
- * @param swjdp The DAP connected to the MEM-AP.
+ * @param dap The DAP connected to the MEM-AP.
* @param address Address to be written; it must be writable by
* the currently selected MEM-AP.
* @param value Word that will be written.
*
* @return ERROR_OK for success; the data was written. Otherwise a fault code.
*/
-int mem_ap_write_atomic_u32(struct swjdp_common *swjdp, uint32_t address,
+int mem_ap_write_atomic_u32(struct adiv5_dap *dap, uint32_t address,
uint32_t value)
{
- int retval = mem_ap_write_u32(swjdp, address, value);
+ int retval = mem_ap_write_u32(dap, address, value);
if (retval != ERROR_OK)
return retval;
- return jtagdp_transaction_endcheck(swjdp);
+ return dap_run(dap);
}
/*****************************************************************************
* *
-* mem_ap_write_buf(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address) *
+* mem_ap_write_buf(struct adiv5_dap *dap, uint8_t *buffer, int count, uint32_t address, bool addr_incr) *
* *
* Write a buffer in target order (little endian) *
* *
*****************************************************************************/
-int mem_ap_write_buf_u32(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+int mem_ap_write_buf_u32(struct adiv5_dap *dap, const uint8_t *buffer, int count, uint32_t address, bool addr_incr)
{
int wcount, blocksize, writecount, errorcount = 0, retval = ERROR_OK;
uint32_t adr = address;
- uint8_t* pBuffer = buffer;
-
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
+ const uint8_t *pBuffer = buffer;
+ uint32_t incr_flag = CSW_ADDRINC_OFF;
count >>= 2;
wcount = count;
/* if we have an unaligned access - reorder data */
- if (adr & 0x3u)
- {
- for (writecount = 0; writecount < count; writecount++)
- {
+ if (adr & 0x3u) {
+ for (writecount = 0; writecount < count; writecount++) {
int i;
uint32_t outvalue;
memcpy(&outvalue, pBuffer, sizeof(uint32_t));
- for (i = 0; i < 4; i++)
- {
- *((uint8_t*)pBuffer + (adr & 0x3)) = outvalue;
+ for (i = 0; i < 4; i++) {
+ *((uint8_t *)pBuffer + (adr & 0x3)) = outvalue;
outvalue >>= 8;
adr++;
}
}
}
- while (wcount > 0)
- {
+ while (wcount > 0) {
/* Adjust to write blocks within boundaries aligned to the TAR autoincremnent size*/
- blocksize = max_tar_block_size(swjdp->tar_autoincr_block, address);
+ blocksize = max_tar_block_size(dap->tar_autoincr_block, address);
if (wcount < blocksize)
blocksize = wcount;
if (blocksize == 0)
blocksize = 1;
- dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_SINGLE, address);
+ if (addr_incr)
+ incr_flag = CSW_ADDRINC_SINGLE;
- for (writecount = 0; writecount < blocksize; writecount++)
- {
- dap_ap_write_reg(swjdp, AP_REG_DRW, buffer + 4 * writecount);
+ retval = dap_setup_accessport(dap, CSW_32BIT | incr_flag, address);
+ if (retval != ERROR_OK)
+ return retval;
+
+ for (writecount = 0; writecount < blocksize; writecount++) {
+ uint32_t tmp;
+ tmp = buf_get_u32(buffer + 4 * writecount, 0, 32);
+ retval = dap_queue_ap_write(dap, AP_REG_DRW, tmp);
+ if (retval != ERROR_OK)
+ break;
}
- if (jtagdp_transaction_endcheck(swjdp) == ERROR_OK)
- {
+ retval = dap_run(dap);
+ if (retval == ERROR_OK) {
wcount = wcount - blocksize;
- address = address + 4 * blocksize;
+ if (addr_incr)
+ address = address + 4 * blocksize;
buffer = buffer + 4 * blocksize;
- }
- else
- {
+ } else
errorcount++;
- }
- if (errorcount > 1)
- {
+ if (errorcount > 1) {
LOG_WARNING("Block write error address 0x%" PRIx32 ", wcount 0x%x", address, wcount);
- return ERROR_JTAG_DEVICE_ERROR;
+ return retval;
}
}
return retval;
}
-static int mem_ap_write_buf_packed_u16(struct swjdp_common *swjdp,
- uint8_t *buffer, int count, uint32_t address)
+static int mem_ap_write_buf_packed_u16(struct adiv5_dap *dap,
+ const uint8_t *buffer, int count, uint32_t address)
{
int retval = ERROR_OK;
int wcount, blocksize, writecount, i;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
wcount = count >> 1;
- while (wcount > 0)
- {
+ while (wcount > 0) {
int nbytes;
/* Adjust to write blocks within boundaries aligned to the TAR autoincremnent size*/
- blocksize = max_tar_block_size(swjdp->tar_autoincr_block, address);
+ blocksize = max_tar_block_size(dap->tar_autoincr_block, address);
if (wcount < blocksize)
blocksize = wcount;
if (blocksize == 0)
blocksize = 1;
- dap_setup_accessport(swjdp, CSW_16BIT | CSW_ADDRINC_PACKED, address);
+ retval = dap_setup_accessport(dap, CSW_16BIT | CSW_ADDRINC_PACKED, address);
+ if (retval != ERROR_OK)
+ return retval;
writecount = blocksize;
- do
- {
+ do {
nbytes = MIN((writecount << 1), 4);
- if (nbytes < 4)
- {
- if (mem_ap_write_buf_u16(swjdp, buffer,
- nbytes, address) != ERROR_OK)
- {
+ if (nbytes < 4) {
+ retval = mem_ap_write_buf_u16(dap, buffer,
+ nbytes, address);
+ if (retval != ERROR_OK) {
LOG_WARNING("Block write error address "
"0x%" PRIx32 ", count 0x%x",
address, count);
- return ERROR_JTAG_DEVICE_ERROR;
+ return retval;
}
address += nbytes >> 1;
- }
- else
- {
+ } else {
uint32_t outvalue;
memcpy(&outvalue, buffer, sizeof(uint32_t));
- for (i = 0; i < nbytes; i++)
- {
- *((uint8_t*)buffer + (address & 0x3)) = outvalue;
+ for (i = 0; i < nbytes; i++) {
+ *((uint8_t *)buffer + (address & 0x3)) = outvalue;
outvalue >>= 8;
address++;
}
memcpy(&outvalue, buffer, sizeof(uint32_t));
- dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
- {
+ retval = dap_queue_ap_write(dap,
+ AP_REG_DRW, outvalue);
+ if (retval != ERROR_OK)
+ break;
+
+ retval = dap_run(dap);
+ if (retval != ERROR_OK) {
LOG_WARNING("Block write error address "
"0x%" PRIx32 ", count 0x%x",
address, count);
- return ERROR_JTAG_DEVICE_ERROR;
+ return retval;
}
}
return retval;
}
-int mem_ap_write_buf_u16(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+int mem_ap_write_buf_u16(struct adiv5_dap *dap, const uint8_t *buffer, int count, uint32_t address)
{
int retval = ERROR_OK;
if (count >= 4)
- return mem_ap_write_buf_packed_u16(swjdp, buffer, count, address);
+ return mem_ap_write_buf_packed_u16(dap, buffer, count, address);
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
- while (count > 0)
- {
- dap_setup_accessport(swjdp, CSW_16BIT | CSW_ADDRINC_SINGLE, address);
+ while (count > 0) {
+ retval = dap_setup_accessport(dap, CSW_16BIT | CSW_ADDRINC_SINGLE, address);
+ if (retval != ERROR_OK)
+ return retval;
uint16_t svalue;
memcpy(&svalue, buffer, sizeof(uint16_t));
uint32_t outvalue = (uint32_t)svalue << 8 * (address & 0x3);
- dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- retval = jtagdp_transaction_endcheck(swjdp);
+ retval = dap_queue_ap_write(dap, AP_REG_DRW, outvalue);
+ if (retval != ERROR_OK)
+ break;
+
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ break;
+
count -= 2;
address += 2;
buffer += 2;
return retval;
}
-static int mem_ap_write_buf_packed_u8(struct swjdp_common *swjdp,
- uint8_t *buffer, int count, uint32_t address)
+static int mem_ap_write_buf_packed_u8(struct adiv5_dap *dap,
+ const uint8_t *buffer, int count, uint32_t address)
{
int retval = ERROR_OK;
int wcount, blocksize, writecount, i;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
wcount = count;
- while (wcount > 0)
- {
+ while (wcount > 0) {
int nbytes;
/* Adjust to write blocks within boundaries aligned to the TAR autoincremnent size*/
- blocksize = max_tar_block_size(swjdp->tar_autoincr_block, address);
+ blocksize = max_tar_block_size(dap->tar_autoincr_block, address);
if (wcount < blocksize)
blocksize = wcount;
- dap_setup_accessport(swjdp, CSW_8BIT | CSW_ADDRINC_PACKED, address);
+ retval = dap_setup_accessport(dap, CSW_8BIT | CSW_ADDRINC_PACKED, address);
+ if (retval != ERROR_OK)
+ return retval;
writecount = blocksize;
- do
- {
+ do {
nbytes = MIN(writecount, 4);
- if (nbytes < 4)
- {
- if (mem_ap_write_buf_u8(swjdp, buffer, nbytes, address) != ERROR_OK)
- {
+ if (nbytes < 4) {
+ retval = mem_ap_write_buf_u8(dap, buffer, nbytes, address);
+ if (retval != ERROR_OK) {
LOG_WARNING("Block write error address "
"0x%" PRIx32 ", count 0x%x",
address, count);
- return ERROR_JTAG_DEVICE_ERROR;
+ return retval;
}
address += nbytes;
- }
- else
- {
+ } else {
uint32_t outvalue;
memcpy(&outvalue, buffer, sizeof(uint32_t));
- for (i = 0; i < nbytes; i++)
- {
- *((uint8_t*)buffer + (address & 0x3)) = outvalue;
+ for (i = 0; i < nbytes; i++) {
+ *((uint8_t *)buffer + (address & 0x3)) = outvalue;
outvalue >>= 8;
address++;
}
memcpy(&outvalue, buffer, sizeof(uint32_t));
- dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
- {
+ retval = dap_queue_ap_write(dap,
+ AP_REG_DRW, outvalue);
+ if (retval != ERROR_OK)
+ break;
+
+ retval = dap_run(dap);
+ if (retval != ERROR_OK) {
LOG_WARNING("Block write error address "
"0x%" PRIx32 ", count 0x%x",
address, count);
- return ERROR_JTAG_DEVICE_ERROR;
+ return retval;
}
}
return retval;
}
-int mem_ap_write_buf_u8(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+int mem_ap_write_buf_u8(struct adiv5_dap *dap, const uint8_t *buffer, int count, uint32_t address)
{
int retval = ERROR_OK;
if (count >= 4)
- return mem_ap_write_buf_packed_u8(swjdp, buffer, count, address);
+ return mem_ap_write_buf_packed_u8(dap, buffer, count, address);
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
- while (count > 0)
- {
- dap_setup_accessport(swjdp, CSW_8BIT | CSW_ADDRINC_SINGLE, address);
+ while (count > 0) {
+ retval = dap_setup_accessport(dap, CSW_8BIT | CSW_ADDRINC_SINGLE, address);
+ if (retval != ERROR_OK)
+ return retval;
uint32_t outvalue = (uint32_t)*buffer << 8 * (address & 0x3);
- dap_ap_write_reg_u32(swjdp, AP_REG_DRW, outvalue);
- retval = jtagdp_transaction_endcheck(swjdp);
+ retval = dap_queue_ap_write(dap, AP_REG_DRW, outvalue);
+ if (retval != ERROR_OK)
+ break;
+
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ break;
+
count--;
address++;
buffer++;
return retval;
}
-/*********************************************************************************
-* *
-* mem_ap_read_buf_u32(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address) *
-* *
-* Read block fast in target order (little endian) into a buffer *
-* *
-**********************************************************************************/
-int mem_ap_read_buf_u32(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+/* FIXME don't import ... this is a temporary workaround for the
+ * mem_ap_read_buf_u32() mess, until it's no longer JTAG-specific.
+ */
+extern int adi_jtag_dp_scan(struct adiv5_dap *dap,
+ uint8_t instr, uint8_t reg_addr, uint8_t RnW,
+ uint8_t *outvalue, uint8_t *invalue, uint8_t *ack);
+
+/**
+ * Synchronously read a block of 32-bit words into a buffer
+ * @param dap The DAP connected to the MEM-AP.
+ * @param buffer where the words will be stored (in host byte order).
+ * @param count How many words to read.
+ * @param address Memory address from which to read words; all the
+ * @param addr_incr if true, increment the source address for each u32
+ * words must be readable by the currently selected MEM-AP.
+ */
+int mem_ap_read_buf_u32(struct adiv5_dap *dap, uint8_t *buffer,
+ int count, uint32_t address, bool addr_incr)
{
int wcount, blocksize, readcount, errorcount = 0, retval = ERROR_OK;
uint32_t adr = address;
- uint8_t* pBuffer = buffer;
-
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
+ uint8_t *pBuffer = buffer;
+ uint32_t incr_flag = CSW_ADDRINC_OFF;
count >>= 2;
wcount = count;
- while (wcount > 0)
- {
- /* Adjust to read blocks within boundaries aligned to the TAR autoincremnent size*/
- blocksize = max_tar_block_size(swjdp->tar_autoincr_block, address);
+ while (wcount > 0) {
+ /* Adjust to read blocks within boundaries aligned to the
+ * TAR autoincrement size (at least 2^10). Autoincrement
+ * mode avoids an extra per-word roundtrip to update TAR.
+ */
+ blocksize = max_tar_block_size(dap->tar_autoincr_block,
+ address);
if (wcount < blocksize)
blocksize = wcount;
if (blocksize == 0)
blocksize = 1;
- dap_setup_accessport(swjdp, CSW_32BIT | CSW_ADDRINC_SINGLE, address);
+ if (addr_incr)
+ incr_flag = CSW_ADDRINC_SINGLE;
+
+ retval = dap_setup_accessport(dap, CSW_32BIT | incr_flag,
+ address);
+ if (retval != ERROR_OK)
+ return retval;
+
+ /* FIXME remove these three calls to adi_jtag_dp_scan(),
+ * so this routine becomes transport-neutral. Be careful
+ * not to cause performance problems with JTAG; would it
+ * suffice to loop over dap_queue_ap_read(), or would that
+ * be slower when JTAG is the chosen transport?
+ */
/* Scan out first read */
- adi_jtag_dp_scan(swjdp, JTAG_DP_APACC, AP_REG_DRW,
+ retval = adi_jtag_dp_scan(dap, JTAG_DP_APACC, AP_REG_DRW,
DPAP_READ, 0, NULL, NULL);
- for (readcount = 0; readcount < blocksize - 1; readcount++)
- {
+ if (retval != ERROR_OK)
+ return retval;
+ for (readcount = 0; readcount < blocksize - 1; readcount++) {
/* Scan out next read; scan in posted value for the
* previous one. Assumes read is acked "OK/FAULT",
* and CTRL_STAT says that meant "OK".
*/
- adi_jtag_dp_scan(swjdp, JTAG_DP_APACC, AP_REG_DRW,
+ retval = adi_jtag_dp_scan(dap, JTAG_DP_APACC, AP_REG_DRW,
DPAP_READ, 0, buffer + 4 * readcount,
- &swjdp->ack);
+ &dap->ack);
+ if (retval != ERROR_OK)
+ return retval;
}
/* Scan in last posted value; RDBUFF has no other effect,
* assuming ack is OK/FAULT and CTRL_STAT says "OK".
*/
- adi_jtag_dp_scan(swjdp, JTAG_DP_DPACC, DP_RDBUFF,
+ retval = adi_jtag_dp_scan(dap, JTAG_DP_DPACC, DP_RDBUFF,
DPAP_READ, 0, buffer + 4 * readcount,
- &swjdp->ack);
- if (jtagdp_transaction_endcheck(swjdp) == ERROR_OK)
- {
- wcount = wcount - blocksize;
- address += 4 * blocksize;
- buffer += 4 * blocksize;
- }
- else
- {
- errorcount++;
- }
+ &dap->ack);
+ if (retval != ERROR_OK)
+ return retval;
- if (errorcount > 1)
- {
- LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
- return ERROR_JTAG_DEVICE_ERROR;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK) {
+ errorcount++;
+ if (errorcount <= 1) {
+ /* try again */
+ continue;
+ }
+ LOG_WARNING("Block read error address 0x%" PRIx32, address);
+ return retval;
}
+ wcount = wcount - blocksize;
+ if (addr_incr)
+ address += 4 * blocksize;
+ buffer += 4 * blocksize;
}
/* if we have an unaligned access - reorder data */
- if (adr & 0x3u)
- {
- for (readcount = 0; readcount < count; readcount++)
- {
+ if (adr & 0x3u) {
+ for (readcount = 0; readcount < count; readcount++) {
int i;
uint32_t data;
memcpy(&data, pBuffer, sizeof(uint32_t));
- for (i = 0; i < 4; i++)
- {
- *((uint8_t*)pBuffer) = (data >> 8 * (adr & 0x3));
+ for (i = 0; i < 4; i++) {
+ *((uint8_t *)pBuffer) =
+ (data >> 8 * (adr & 0x3));
pBuffer++;
adr++;
}
return retval;
}
-static int mem_ap_read_buf_packed_u16(struct swjdp_common *swjdp,
+static int mem_ap_read_buf_packed_u16(struct adiv5_dap *dap,
uint8_t *buffer, int count, uint32_t address)
{
uint32_t invalue;
int retval = ERROR_OK;
int wcount, blocksize, readcount, i;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
wcount = count >> 1;
- while (wcount > 0)
- {
+ while (wcount > 0) {
int nbytes;
/* Adjust to read blocks within boundaries aligned to the TAR autoincremnent size*/
- blocksize = max_tar_block_size(swjdp->tar_autoincr_block, address);
+ blocksize = max_tar_block_size(dap->tar_autoincr_block, address);
if (wcount < blocksize)
blocksize = wcount;
- dap_setup_accessport(swjdp, CSW_16BIT | CSW_ADDRINC_PACKED, address);
+ retval = dap_setup_accessport(dap, CSW_16BIT | CSW_ADDRINC_PACKED, address);
+ if (retval != ERROR_OK)
+ return retval;
/* handle unaligned data at 4k boundary */
if (blocksize == 0)
blocksize = 1;
readcount = blocksize;
- do
- {
- dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
- {
+ do {
+ retval = dap_queue_ap_read(dap, AP_REG_DRW, &invalue);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK) {
LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
- return ERROR_JTAG_DEVICE_ERROR;
+ return retval;
}
nbytes = MIN((readcount << 1), 4);
- for (i = 0; i < nbytes; i++)
- {
- *((uint8_t*)buffer) = (invalue >> 8 * (address & 0x3));
+ for (i = 0; i < nbytes; i++) {
+ *((uint8_t *)buffer) = (invalue >> 8 * (address & 0x3));
buffer++;
address++;
}
return retval;
}
-int mem_ap_read_buf_u16(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+/**
+ * Synchronously read a block of 16-bit halfwords into a buffer
+ * @param dap The DAP connected to the MEM-AP.
+ * @param buffer where the halfwords will be stored (in host byte order).
+ * @param count How many halfwords to read.
+ * @param address Memory address from which to read words; all the
+ * words must be readable by the currently selected MEM-AP.
+ */
+int mem_ap_read_buf_u16(struct adiv5_dap *dap, uint8_t *buffer,
+ int count, uint32_t address)
{
uint32_t invalue, i;
int retval = ERROR_OK;
if (count >= 4)
- return mem_ap_read_buf_packed_u16(swjdp, buffer, count, address);
+ return mem_ap_read_buf_packed_u16(dap, buffer, count, address);
+
+ while (count > 0) {
+ retval = dap_setup_accessport(dap, CSW_16BIT | CSW_ADDRINC_SINGLE, address);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_queue_ap_read(dap, AP_REG_DRW, &invalue);
+ if (retval != ERROR_OK)
+ break;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ break;
- while (count > 0)
- {
- dap_setup_accessport(swjdp, CSW_16BIT | CSW_ADDRINC_SINGLE, address);
- dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- retval = jtagdp_transaction_endcheck(swjdp);
- if (address & 0x1)
- {
- for (i = 0; i < 2; i++)
- {
- *((uint8_t*)buffer) = (invalue >> 8 * (address & 0x3));
+ if (address & 0x1) {
+ for (i = 0; i < 2; i++) {
+ *((uint8_t *)buffer) = (invalue >> 8 * (address & 0x3));
buffer++;
address++;
}
- }
- else
- {
+ } else {
uint16_t svalue = (invalue >> 8 * (address & 0x3));
memcpy(buffer, &svalue, sizeof(uint16_t));
address += 2;
* The solution is to arrange for a large out/in scan in this loop and
* and convert data afterwards.
*/
-static int mem_ap_read_buf_packed_u8(struct swjdp_common *swjdp,
+static int mem_ap_read_buf_packed_u8(struct adiv5_dap *dap,
uint8_t *buffer, int count, uint32_t address)
{
uint32_t invalue;
int retval = ERROR_OK;
int wcount, blocksize, readcount, i;
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
-
wcount = count;
- while (wcount > 0)
- {
+ while (wcount > 0) {
int nbytes;
/* Adjust to read blocks within boundaries aligned to the TAR autoincremnent size*/
- blocksize = max_tar_block_size(swjdp->tar_autoincr_block, address);
+ blocksize = max_tar_block_size(dap->tar_autoincr_block, address);
if (wcount < blocksize)
blocksize = wcount;
- dap_setup_accessport(swjdp, CSW_8BIT | CSW_ADDRINC_PACKED, address);
+ retval = dap_setup_accessport(dap, CSW_8BIT | CSW_ADDRINC_PACKED, address);
+ if (retval != ERROR_OK)
+ return retval;
readcount = blocksize;
- do
- {
- dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- if (jtagdp_transaction_endcheck(swjdp) != ERROR_OK)
- {
+ do {
+ retval = dap_queue_ap_read(dap, AP_REG_DRW, &invalue);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK) {
LOG_WARNING("Block read error address 0x%" PRIx32 ", count 0x%x", address, count);
- return ERROR_JTAG_DEVICE_ERROR;
+ return retval;
}
nbytes = MIN(readcount, 4);
- for (i = 0; i < nbytes; i++)
- {
- *((uint8_t*)buffer) = (invalue >> 8 * (address & 0x3));
+ for (i = 0; i < nbytes; i++) {
+ *((uint8_t *)buffer) = (invalue >> 8 * (address & 0x3));
buffer++;
address++;
}
return retval;
}
-int mem_ap_read_buf_u8(struct swjdp_common *swjdp, uint8_t *buffer, int count, uint32_t address)
+/**
+ * Synchronously read a block of bytes into a buffer
+ * @param dap The DAP connected to the MEM-AP.
+ * @param buffer where the bytes will be stored.
+ * @param count How many bytes to read.
+ * @param address Memory address from which to read data; all the
+ * data must be readable by the currently selected MEM-AP.
+ */
+int mem_ap_read_buf_u8(struct adiv5_dap *dap, uint8_t *buffer,
+ int count, uint32_t address)
{
uint32_t invalue;
int retval = ERROR_OK;
if (count >= 4)
- return mem_ap_read_buf_packed_u8(swjdp, buffer, count, address);
+ return mem_ap_read_buf_packed_u8(dap, buffer, count, address);
- swjdp->trans_mode = TRANS_MODE_COMPOSITE;
+ while (count > 0) {
+ retval = dap_setup_accessport(dap, CSW_8BIT | CSW_ADDRINC_SINGLE, address);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_queue_ap_read(dap, AP_REG_DRW, &invalue);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ break;
- while (count > 0)
- {
- dap_setup_accessport(swjdp, CSW_8BIT | CSW_ADDRINC_SINGLE, address);
- dap_ap_read_reg_u32(swjdp, AP_REG_DRW, &invalue);
- retval = jtagdp_transaction_endcheck(swjdp);
- *((uint8_t*)buffer) = (invalue >> 8 * (address & 0x3));
+ *((uint8_t *)buffer) = (invalue >> 8 * (address & 0x3));
count--;
address++;
buffer++;
return retval;
}
+/*--------------------------------------------------------------------*/
+/* Wrapping function with selection of AP */
+/*--------------------------------------------------------------------*/
+int mem_ap_sel_read_u32(struct adiv5_dap *swjdp, uint8_t ap,
+ uint32_t address, uint32_t *value)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_read_u32(swjdp, address, value);
+}
+
+int mem_ap_sel_write_u32(struct adiv5_dap *swjdp, uint8_t ap,
+ uint32_t address, uint32_t value)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_write_u32(swjdp, address, value);
+}
+
+int mem_ap_sel_read_atomic_u32(struct adiv5_dap *swjdp, uint8_t ap,
+ uint32_t address, uint32_t *value)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_read_atomic_u32(swjdp, address, value);
+}
+
+int mem_ap_sel_write_atomic_u32(struct adiv5_dap *swjdp, uint8_t ap,
+ uint32_t address, uint32_t value)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_write_atomic_u32(swjdp, address, value);
+}
+
+int mem_ap_sel_read_buf_u8(struct adiv5_dap *swjdp, uint8_t ap,
+ uint8_t *buffer, int count, uint32_t address)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_read_buf_u8(swjdp, buffer, count, address);
+}
+
+int mem_ap_sel_read_buf_u16(struct adiv5_dap *swjdp, uint8_t ap,
+ uint8_t *buffer, int count, uint32_t address)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_read_buf_u16(swjdp, buffer, count, address);
+}
+
+int mem_ap_sel_read_buf_u32_noincr(struct adiv5_dap *swjdp, uint8_t ap,
+ uint8_t *buffer, int count, uint32_t address)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_read_buf_u32(swjdp, buffer, count, address, false);
+}
+
+int mem_ap_sel_read_buf_u32(struct adiv5_dap *swjdp, uint8_t ap,
+ uint8_t *buffer, int count, uint32_t address)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_read_buf_u32(swjdp, buffer, count, address, true);
+}
+
+int mem_ap_sel_write_buf_u8(struct adiv5_dap *swjdp, uint8_t ap,
+ const uint8_t *buffer, int count, uint32_t address)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_write_buf_u8(swjdp, buffer, count, address);
+}
+
+int mem_ap_sel_write_buf_u16(struct adiv5_dap *swjdp, uint8_t ap,
+ const uint8_t *buffer, int count, uint32_t address)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_write_buf_u16(swjdp, buffer, count, address);
+}
+
+int mem_ap_sel_write_buf_u32(struct adiv5_dap *swjdp, uint8_t ap,
+ const uint8_t *buffer, int count, uint32_t address)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_write_buf_u32(swjdp, buffer, count, address, true);
+}
+
+int mem_ap_sel_write_buf_u32_noincr(struct adiv5_dap *swjdp, uint8_t ap,
+ const uint8_t *buffer, int count, uint32_t address)
+{
+ dap_ap_select(swjdp, ap);
+ return mem_ap_write_buf_u32(swjdp, buffer, count, address, false);
+}
+
+#define MDM_REG_STAT 0x00
+#define MDM_REG_CTRL 0x04
+#define MDM_REG_ID 0xfc
+
+#define MDM_STAT_FMEACK (1<<0)
+#define MDM_STAT_FREADY (1<<1)
+#define MDM_STAT_SYSSEC (1<<2)
+#define MDM_STAT_SYSRES (1<<3)
+#define MDM_STAT_FMEEN (1<<5)
+#define MDM_STAT_BACKDOOREN (1<<6)
+#define MDM_STAT_LPEN (1<<7)
+#define MDM_STAT_VLPEN (1<<8)
+#define MDM_STAT_LLSMODEXIT (1<<9)
+#define MDM_STAT_VLLSXMODEXIT (1<<10)
+#define MDM_STAT_CORE_HALTED (1<<16)
+#define MDM_STAT_CORE_SLEEPDEEP (1<<17)
+#define MDM_STAT_CORESLEEPING (1<<18)
+
+#define MEM_CTRL_FMEIP (1<<0)
+#define MEM_CTRL_DBG_DIS (1<<1)
+#define MEM_CTRL_DBG_REQ (1<<2)
+#define MEM_CTRL_SYS_RES_REQ (1<<3)
+#define MEM_CTRL_CORE_HOLD_RES (1<<4)
+#define MEM_CTRL_VLLSX_DBG_REQ (1<<5)
+#define MEM_CTRL_VLLSX_DBG_ACK (1<<6)
+#define MEM_CTRL_VLLSX_STAT_ACK (1<<7)
+
+/**
+ *
+ */
+int dap_syssec_kinetis_mdmap(struct adiv5_dap *dap)
+{
+ uint32_t val;
+ int retval;
+ enum reset_types jtag_reset_config = jtag_get_reset_config();
+
+ dap_ap_select(dap, 1);
+
+ /* first check mdm-ap id register */
+ retval = dap_queue_ap_read(dap, MDM_REG_ID, &val);
+ if (retval != ERROR_OK)
+ return retval;
+ dap_run(dap);
+
+ if (val != 0x001C0000) {
+ LOG_DEBUG("id doesn't match %08X != 0x001C0000", val);
+ dap_ap_select(dap, 0);
+ return ERROR_FAIL;
+ }
+
+ /* read and parse status register
+ * it's important that the device is out of
+ * reset here
+ */
+ retval = dap_queue_ap_read(dap, MDM_REG_STAT, &val);
+ if (retval != ERROR_OK)
+ return retval;
+ dap_run(dap);
+
+ LOG_DEBUG("MDM_REG_STAT %08X", val);
+
+ if ((val & (MDM_STAT_SYSSEC|MDM_STAT_FREADY)) != (MDM_STAT_FREADY)) {
+ LOG_DEBUG("MDMAP: system is secured, masserase needed");
+
+ if (!(val & MDM_STAT_FMEEN))
+ LOG_DEBUG("MDMAP: masserase is disabled");
+ else {
+ /* we need to assert reset */
+ if (jtag_reset_config & RESET_HAS_SRST) {
+ /* default to asserting srst */
+ adapter_assert_reset();
+ } else {
+ LOG_DEBUG("SRST not configured");
+ dap_ap_select(dap, 0);
+ return ERROR_FAIL;
+ }
+
+ while (1) {
+ retval = dap_queue_ap_write(dap, MDM_REG_CTRL, MEM_CTRL_FMEIP);
+ if (retval != ERROR_OK)
+ return retval;
+ dap_run(dap);
+ /* read status register and wait for ready */
+ retval = dap_queue_ap_read(dap, MDM_REG_STAT, &val);
+ if (retval != ERROR_OK)
+ return retval;
+ dap_run(dap);
+ LOG_DEBUG("MDM_REG_STAT %08X", val);
+
+ if ((val & 1))
+ break;
+ }
+
+ while (1) {
+ retval = dap_queue_ap_write(dap, MDM_REG_CTRL, 0);
+ if (retval != ERROR_OK)
+ return retval;
+ dap_run(dap);
+ /* read status register */
+ retval = dap_queue_ap_read(dap, MDM_REG_STAT, &val);
+ if (retval != ERROR_OK)
+ return retval;
+ dap_run(dap);
+ LOG_DEBUG("MDM_REG_STAT %08X", val);
+ /* read control register and wait for ready */
+ retval = dap_queue_ap_read(dap, MDM_REG_CTRL, &val);
+ if (retval != ERROR_OK)
+ return retval;
+ dap_run(dap);
+ LOG_DEBUG("MDM_REG_CTRL %08X", val);
+
+ if (val == 0x00)
+ break;
+ }
+ }
+ }
+
+ dap_ap_select(dap, 0);
+
+ return ERROR_OK;
+}
+
+/** */
+struct dap_syssec_filter {
+ /** */
+ uint32_t idcode;
+ /** */
+ int (*dap_init)(struct adiv5_dap *dap);
+};
+
+/** */
+static struct dap_syssec_filter dap_syssec_filter_data[] = {
+ { 0x4BA00477, dap_syssec_kinetis_mdmap }
+};
+
+/**
+ *
+ */
+int dap_syssec(struct adiv5_dap *dap)
+{
+ unsigned int i;
+ struct jtag_tap *tap;
+
+ for (i = 0; i < sizeof(dap_syssec_filter_data); i++) {
+ tap = dap->jtag_info->tap;
+
+ while (tap != NULL) {
+ if (tap->hasidcode && (dap_syssec_filter_data[i].idcode == tap->idcode)) {
+ LOG_DEBUG("DAP: mdmap_init for idcode: %08x", tap->idcode);
+ dap_syssec_filter_data[i].dap_init(dap);
+ }
+ tap = tap->next_tap;
+ }
+ }
+
+ return ERROR_OK;
+}
+
+/*--------------------------------------------------------------------------*/
+
+
+/* FIXME don't import ... just initialize as
+ * part of DAP transport setup
+*/
+extern const struct dap_ops jtag_dp_ops;
+
+/*--------------------------------------------------------------------------*/
+
/**
* Initialize a DAP. This sets up the power domains, prepares the DP
* for further use, and arranges to use AP #0 for all AP operations
* until dap_ap-select() changes that policy.
*
- * @param swjdp The DAP being initialized.
+ * @param dap The DAP being initialized.
*
* @todo Rename this. We also need an initialization scheme which account
* for SWD transports not just JTAG; that will need to address differences
* in layering. (JTAG is useful without any debug target; but not SWD.)
* And this may not even use an AHB-AP ... e.g. DAP-Lite uses an APB-AP.
*/
-int ahbap_debugport_init(struct swjdp_common *swjdp)
+int ahbap_debugport_init(struct adiv5_dap *dap)
{
- uint32_t idreg, romaddr, dummy;
uint32_t ctrlstat;
int cnt = 0;
int retval;
LOG_DEBUG(" ");
+ /* JTAG-DP or SWJ-DP, in JTAG mode
+ * ... for SWD mode this is patched as part
+ * of link switchover
+ */
+ if (!dap->ops)
+ dap->ops = &jtag_dp_ops;
+
/* Default MEM-AP setup.
*
* REVISIT AP #0 may be an inappropriate default for this.
* Should we probe, or take a hint from the caller?
* Presumably we can ignore the possibility of multiple APs.
*/
- swjdp->apsel = !0;
- dap_ap_select(swjdp, 0);
+ dap->ap_current = !0;
+ dap_ap_select(dap, 0);
/* DP initialization */
- swjdp->trans_mode = TRANS_MODE_ATOMIC;
- dap_dp_read_reg(swjdp, &dummy, DP_CTRL_STAT);
- dap_dp_write_reg(swjdp, SSTICKYERR, DP_CTRL_STAT);
- dap_dp_read_reg(swjdp, &dummy, DP_CTRL_STAT);
- swjdp->dp_ctrl_stat = CDBGPWRUPREQ | CSYSPWRUPREQ;
+ retval = dap_queue_dp_read(dap, DP_CTRL_STAT, NULL);
+ if (retval != ERROR_OK)
+ return retval;
- dap_dp_write_reg(swjdp, swjdp->dp_ctrl_stat, DP_CTRL_STAT);
- dap_dp_read_reg(swjdp, &ctrlstat, DP_CTRL_STAT);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
+ retval = dap_queue_dp_write(dap, DP_CTRL_STAT, SSTICKYERR);
+ if (retval != ERROR_OK)
+ return retval;
+
+ retval = dap_queue_dp_read(dap, DP_CTRL_STAT, NULL);
+ if (retval != ERROR_OK)
+ return retval;
+
+ dap->dp_ctrl_stat = CDBGPWRUPREQ | CSYSPWRUPREQ;
+ retval = dap_queue_dp_write(dap, DP_CTRL_STAT, dap->dp_ctrl_stat);
+ if (retval != ERROR_OK)
+ return retval;
+
+ retval = dap_queue_dp_read(dap, DP_CTRL_STAT, &ctrlstat);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
return retval;
/* Check that we have debug power domains activated */
- while (!(ctrlstat & CDBGPWRUPACK) && (cnt++ < 10))
- {
+ while (!(ctrlstat & CDBGPWRUPACK) && (cnt++ < 10)) {
LOG_DEBUG("DAP: wait CDBGPWRUPACK");
- dap_dp_read_reg(swjdp, &ctrlstat, DP_CTRL_STAT);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
+ retval = dap_queue_dp_read(dap, DP_CTRL_STAT, &ctrlstat);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
return retval;
alive_sleep(10);
}
- while (!(ctrlstat & CSYSPWRUPACK) && (cnt++ < 10))
- {
+ while (!(ctrlstat & CSYSPWRUPACK) && (cnt++ < 10)) {
LOG_DEBUG("DAP: wait CSYSPWRUPACK");
- dap_dp_read_reg(swjdp, &ctrlstat, DP_CTRL_STAT);
- if ((retval = jtag_execute_queue()) != ERROR_OK)
+ retval = dap_queue_dp_read(dap, DP_CTRL_STAT, &ctrlstat);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
return retval;
alive_sleep(10);
}
- dap_dp_read_reg(swjdp, &dummy, DP_CTRL_STAT);
+ retval = dap_queue_dp_read(dap, DP_CTRL_STAT, NULL);
+ if (retval != ERROR_OK)
+ return retval;
/* With debug power on we can activate OVERRUN checking */
- swjdp->dp_ctrl_stat = CDBGPWRUPREQ | CSYSPWRUPREQ | CORUNDETECT;
- dap_dp_write_reg(swjdp, swjdp->dp_ctrl_stat, DP_CTRL_STAT);
- dap_dp_read_reg(swjdp, &dummy, DP_CTRL_STAT);
-
- /*
- * REVISIT this isn't actually *initializing* anything in an AP,
- * and doesn't care if it's a MEM-AP at all (much less AHB-AP).
- * Should it? If the ROM address is valid, is this the right
- * place to scan the table and do any topology detection?
- */
- dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &idreg);
- dap_ap_read_reg_u32(swjdp, AP_REG_BASE, &romaddr);
+ dap->dp_ctrl_stat = CDBGPWRUPREQ | CSYSPWRUPREQ | CORUNDETECT;
+ retval = dap_queue_dp_write(dap, DP_CTRL_STAT, dap->dp_ctrl_stat);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_queue_dp_read(dap, DP_CTRL_STAT, NULL);
+ if (retval != ERROR_OK)
+ return retval;
- LOG_DEBUG("MEM-AP #%d ID Register 0x%" PRIx32
- ", Debug ROM Address 0x%" PRIx32,
- swjdp->apsel, idreg, romaddr);
+ dap_syssec(dap);
return ERROR_OK;
}
/* CID interpretation -- see ARM IHI 0029B section 3
* and ARM IHI 0031A table 13-3.
*/
-static const char *class_description[16] ={
+static const char *class_description[16] = {
"Reserved", "ROM table", "Reserved", "Reserved",
"Reserved", "Reserved", "Reserved", "Reserved",
"Reserved", "CoreSight component", "Reserved", "Peripheral Test Block",
"Reserved", "OptimoDE DESS",
- "Generic IP component", "PrimeCell or System component"
+ "Generic IP component", "PrimeCell or System component"
};
-static bool
-is_dap_cid_ok(uint32_t cid3, uint32_t cid2, uint32_t cid1, uint32_t cid0)
+static bool is_dap_cid_ok(uint32_t cid3, uint32_t cid2, uint32_t cid1, uint32_t cid0)
{
return cid3 == 0xb1 && cid2 == 0x05
&& ((cid1 & 0x0f) == 0) && cid0 == 0x0d;
}
-int dap_info_command(struct command_context *cmd_ctx,
- struct swjdp_common *swjdp, int apsel)
+int dap_get_debugbase(struct adiv5_dap *dap, int ap,
+ uint32_t *out_dbgbase, uint32_t *out_apid)
{
-
+ uint32_t ap_old;
+ int retval;
uint32_t dbgbase, apid;
+
+ /* AP address is in bits 31:24 of DP_SELECT */
+ if (ap >= 256)
+ return ERROR_COMMAND_SYNTAX_ERROR;
+
+ ap_old = dap->ap_current;
+ dap_ap_select(dap, ap);
+
+ retval = dap_queue_ap_read(dap, AP_REG_BASE, &dbgbase);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_queue_ap_read(dap, AP_REG_IDR, &apid);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
+ /* Excavate the device ID code */
+ struct jtag_tap *tap = dap->jtag_info->tap;
+ while (tap != NULL) {
+ if (tap->hasidcode)
+ break;
+ tap = tap->next_tap;
+ }
+ if (tap == NULL || !tap->hasidcode)
+ return ERROR_OK;
+
+ dap_ap_select(dap, ap_old);
+
+ /* The asignment happens only here to prevent modification of these
+ * values before they are certain. */
+ *out_dbgbase = dbgbase;
+ *out_apid = apid;
+
+ return ERROR_OK;
+}
+
+int dap_lookup_cs_component(struct adiv5_dap *dap, int ap,
+ uint32_t dbgbase, uint8_t type, uint32_t *addr)
+{
+ uint32_t ap_old;
+ uint32_t romentry, entry_offset = 0, component_base, devtype;
+ int retval = ERROR_FAIL;
+
+ if (ap >= 256)
+ return ERROR_COMMAND_SYNTAX_ERROR;
+
+ ap_old = dap->ap_current;
+ dap_ap_select(dap, ap);
+
+ do {
+ retval = mem_ap_read_atomic_u32(dap, (dbgbase&0xFFFFF000) |
+ entry_offset, &romentry);
+ if (retval != ERROR_OK)
+ return retval;
+
+ component_base = (dbgbase & 0xFFFFF000)
+ + (romentry & 0xFFFFF000);
+
+ if (romentry & 0x1) {
+ retval = mem_ap_read_atomic_u32(dap,
+ (component_base & 0xfffff000) | 0xfcc,
+ &devtype);
+ if (retval != ERROR_OK)
+ return retval;
+ if ((devtype & 0xff) == type) {
+ *addr = component_base;
+ retval = ERROR_OK;
+ break;
+ }
+ }
+ entry_offset += 4;
+ } while (romentry > 0);
+
+ dap_ap_select(dap, ap_old);
+
+ return retval;
+}
+
+static int dap_info_command(struct command_context *cmd_ctx,
+ struct adiv5_dap *dap, int ap)
+{
+ int retval;
+ uint32_t dbgbase = 0, apid = 0; /* Silence gcc by initializing */
int romtable_present = 0;
uint8_t mem_ap;
- uint32_t apselold;
+ uint32_t ap_old;
+
+ retval = dap_get_debugbase(dap, ap, &dbgbase, &apid);
+ if (retval != ERROR_OK)
+ return retval;
+
+ ap_old = dap->ap_current;
+ dap_ap_select(dap, ap);
- /* AP address is in bits 31:24 of DP_SELECT */
- if (apsel >= 256)
- return ERROR_INVALID_ARGUMENTS;
-
- apselold = swjdp->apsel;
- dap_ap_select(swjdp, apsel);
- dap_ap_read_reg_u32(swjdp, AP_REG_BASE, &dbgbase);
- dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &apid);
- jtagdp_transaction_endcheck(swjdp);
/* Now we read ROM table ID registers, ref. ARM IHI 0029B sec */
mem_ap = ((apid&0x10000) && ((apid&0x0F) != 0));
command_print(cmd_ctx, "AP ID register 0x%8.8" PRIx32, apid);
- if (apid)
- {
- switch (apid&0x0F)
- {
+ if (apid) {
+ switch (apid&0x0F) {
case 0:
command_print(cmd_ctx, "\tType is JTAG-AP");
break;
* not a ROM table ... or have no such components at all.
*/
if (mem_ap)
- command_print(cmd_ctx, "AP BASE 0x%8.8" PRIx32,
- dbgbase);
- }
- else
- {
- command_print(cmd_ctx, "No AP found at this apsel 0x%x", apsel);
- }
+ command_print(cmd_ctx, "AP BASE 0x%8.8" PRIx32, dbgbase);
+ } else
+ command_print(cmd_ctx, "No AP found at this ap 0x%x", ap);
romtable_present = ((mem_ap) && (dbgbase != 0xFFFFFFFF));
- if (romtable_present)
- {
- uint32_t cid0,cid1,cid2,cid3,memtype,romentry;
+ if (romtable_present) {
+ uint32_t cid0, cid1, cid2, cid3, memtype, romentry;
uint16_t entry_offset;
/* bit 16 of apid indicates a memory access port */
command_print(cmd_ctx, "\tROM table in legacy format");
/* Now we read ROM table ID registers, ref. ARM IHI 0029B sec */
- mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFF0, &cid0);
- mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFF4, &cid1);
- mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFF8, &cid2);
- mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFFC, &cid3);
- mem_ap_read_u32(swjdp, (dbgbase&0xFFFFF000) | 0xFCC, &memtype);
- jtagdp_transaction_endcheck(swjdp);
+ retval = mem_ap_read_u32(dap, (dbgbase&0xFFFFF000) | 0xFF0, &cid0);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = mem_ap_read_u32(dap, (dbgbase&0xFFFFF000) | 0xFF4, &cid1);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = mem_ap_read_u32(dap, (dbgbase&0xFFFFF000) | 0xFF8, &cid2);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = mem_ap_read_u32(dap, (dbgbase&0xFFFFF000) | 0xFFC, &cid3);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = mem_ap_read_u32(dap, (dbgbase&0xFFFFF000) | 0xFCC, &memtype);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
if (!is_dap_cid_ok(cid3, cid2, cid1, cid0))
- command_print(cmd_ctx, "\tCID3 0x%2.2" PRIx32
- ", CID2 0x%2.2" PRIx32
- ", CID1 0x%2.2" PRIx32
- ", CID0 0x%2.2" PRIx32,
- cid3, cid2, cid1, cid0);
+ command_print(cmd_ctx, "\tCID3 0x%2.2x"
+ ", CID2 0x%2.2x"
+ ", CID1 0x%2.2x"
+ ", CID0 0x%2.2x",
+ (unsigned) cid3, (unsigned)cid2,
+ (unsigned) cid1, (unsigned) cid0);
if (memtype & 0x01)
command_print(cmd_ctx, "\tMEMTYPE system memory present on bus");
else
/* Now we read ROM table entries from dbgbase&0xFFFFF000) | 0x000 until we get 0x00000000 */
entry_offset = 0;
- do
- {
- mem_ap_read_atomic_u32(swjdp, (dbgbase&0xFFFFF000) | entry_offset, &romentry);
- command_print(cmd_ctx, "\tROMTABLE[0x%x] = 0x%" PRIx32 "",entry_offset,romentry);
- if (romentry&0x01)
- {
+ do {
+ retval = mem_ap_read_atomic_u32(dap, (dbgbase&0xFFFFF000) | entry_offset, &romentry);
+ if (retval != ERROR_OK)
+ return retval;
+ command_print(cmd_ctx, "\tROMTABLE[0x%x] = 0x%" PRIx32 "", entry_offset, romentry);
+ if (romentry & 0x01) {
uint32_t c_cid0, c_cid1, c_cid2, c_cid3;
uint32_t c_pid0, c_pid1, c_pid2, c_pid3, c_pid4;
- uint32_t component_start, component_base;
+ uint32_t component_base;
unsigned part_num;
char *type, *full;
- component_base = (uint32_t)((dbgbase & 0xFFFFF000)
- + (int)(romentry & 0xFFFFF000));
- mem_ap_read_atomic_u32(swjdp,
- (component_base & 0xFFFFF000) | 0xFE0, &c_pid0);
- mem_ap_read_atomic_u32(swjdp,
- (component_base & 0xFFFFF000) | 0xFE4, &c_pid1);
- mem_ap_read_atomic_u32(swjdp,
- (component_base & 0xFFFFF000) | 0xFE8, &c_pid2);
- mem_ap_read_atomic_u32(swjdp,
- (component_base & 0xFFFFF000) | 0xFEC, &c_pid3);
- mem_ap_read_atomic_u32(swjdp,
- (component_base & 0xFFFFF000) | 0xFD0, &c_pid4);
- mem_ap_read_atomic_u32(swjdp,
- (component_base & 0xFFFFF000) | 0xFF0, &c_cid0);
- mem_ap_read_atomic_u32(swjdp,
- (component_base & 0xFFFFF000) | 0xFF4, &c_cid1);
- mem_ap_read_atomic_u32(swjdp,
- (component_base & 0xFFFFF000) | 0xFF8, &c_cid2);
- mem_ap_read_atomic_u32(swjdp,
- (component_base & 0xFFFFF000) | 0xFFC, &c_cid3);
- component_start = component_base - 0x1000*(c_pid4 >> 4);
-
- command_print(cmd_ctx, "\t\tComponent base address 0x%" PRIx32
- ", start address 0x%" PRIx32,
- component_base, component_start);
+ component_base = (dbgbase & 0xFFFFF000) + (romentry & 0xFFFFF000);
+
+ /* IDs are in last 4K section */
+ retval = mem_ap_read_atomic_u32(dap, component_base + 0xFE0, &c_pid0);
+ if (retval != ERROR_OK)
+ return retval;
+ c_pid0 &= 0xff;
+ retval = mem_ap_read_atomic_u32(dap, component_base + 0xFE4, &c_pid1);
+ if (retval != ERROR_OK)
+ return retval;
+ c_pid1 &= 0xff;
+ retval = mem_ap_read_atomic_u32(dap, component_base + 0xFE8, &c_pid2);
+ if (retval != ERROR_OK)
+ return retval;
+ c_pid2 &= 0xff;
+ retval = mem_ap_read_atomic_u32(dap, component_base + 0xFEC, &c_pid3);
+ if (retval != ERROR_OK)
+ return retval;
+ c_pid3 &= 0xff;
+ retval = mem_ap_read_atomic_u32(dap, component_base + 0xFD0, &c_pid4);
+ if (retval != ERROR_OK)
+ return retval;
+ c_pid4 &= 0xff;
+
+ retval = mem_ap_read_atomic_u32(dap, component_base + 0xFF0, &c_cid0);
+ if (retval != ERROR_OK)
+ return retval;
+ c_cid0 &= 0xff;
+ retval = mem_ap_read_atomic_u32(dap, component_base + 0xFF4, &c_cid1);
+ if (retval != ERROR_OK)
+ return retval;
+ c_cid1 &= 0xff;
+ retval = mem_ap_read_atomic_u32(dap, component_base + 0xFF8, &c_cid2);
+ if (retval != ERROR_OK)
+ return retval;
+ c_cid2 &= 0xff;
+ retval = mem_ap_read_atomic_u32(dap, component_base + 0xFFC, &c_cid3);
+ if (retval != ERROR_OK)
+ return retval;
+ c_cid3 &= 0xff;
+
+ command_print(cmd_ctx, "\t\tComponent base address 0x%" PRIx32 ","
+ "start address 0x%" PRIx32, component_base,
+ /* component may take multiple 4K pages */
+ component_base - 0x1000*(c_pid4 >> 4));
command_print(cmd_ctx, "\t\tComponent class is 0x%x, %s",
(int) (c_cid1 >> 4) & 0xf,
/* See ARM IHI 0029B Table 3-3 */
unsigned minor;
char *major = "Reserved", *subtype = "Reserved";
- mem_ap_read_atomic_u32(swjdp,
+ retval = mem_ap_read_atomic_u32(dap,
(component_base & 0xfffff000) | 0xfcc,
&devtype);
+ if (retval != ERROR_OK)
+ return retval;
minor = (devtype >> 4) & 0x0f;
switch (devtype & 0x0f) {
case 0:
}
if (!is_dap_cid_ok(cid3, cid2, cid1, cid0))
- command_print(cmd_ctx, "\t\tCID3 0x%2.2" PRIx32
- ", CID2 0x%2.2" PRIx32
- ", CID1 0x%2.2" PRIx32
- ", CID0 0x%2.2" PRIx32,
- c_cid3, c_cid2, c_cid1, c_cid0);
- command_print(cmd_ctx, "\t\tPeripheral ID[4..0] = hex "
- "%2.2x %2.2x %2.2x %2.2x %2.2x",
- (int) c_pid4,
- (int) c_pid3, (int) c_pid2,
- (int) c_pid1, (int) c_pid0);
+ command_print(cmd_ctx,
+ "\t\tCID3 0%2.2x"
+ ", CID2 0%2.2x"
+ ", CID1 0%2.2x"
+ ", CID0 0%2.2x",
+ (int) c_cid3,
+ (int) c_cid2,
+ (int)c_cid1,
+ (int)c_cid0);
+ command_print(cmd_ctx,
+ "\t\tPeripheral ID[4..0] = hex "
+ "%2.2x %2.2x %2.2x %2.2x %2.2x",
+ (int) c_pid4, (int) c_pid3, (int) c_pid2,
+ (int) c_pid1, (int) c_pid0);
/* Part number interpretations are from Cortex
* core specs, the CoreSight components TRM
- * (ARM DDI 0314H), and ETM specs; also from
- * chip observation (e.g. TI SDTI).
+ * (ARM DDI 0314H), CoreSight System Design
+ * Guide (ARM DGI 0012D) and ETM specs; also
+ * from chip observation (e.g. TI SDTI).
*/
- part_num = c_pid0 & 0xff;
+ part_num = (c_pid0 & 0xff);
part_num |= (c_pid1 & 0x0f) << 8;
switch (part_num) {
case 0x000:
type = "Cortex-M3 FBP";
full = "(Flash Patch and Breakpoint)";
break;
+ case 0x00c:
+ type = "Cortex-M4 SCS";
+ full = "(System Control Space)";
+ break;
case 0x00d:
type = "CoreSight ETM11";
full = "(Embedded Trace)";
break;
- // case 0x113: what?
+ /* case 0x113: what? */
case 0x120: /* from OMAP3 memmap */
type = "TI SDTI";
full = "(System Debug Trace Interface)";
type = "TI DAPCTL";
full = "";
break;
- case 0x4e0:
- type = "Cortex-M3 ETM";
- full = "(Embedded Trace)";
- break;
case 0x906:
type = "Coresight CTI";
full = "(Cross Trigger)";
type = "Cortex-M3 TPIU";
full = "(Trace Port Interface Unit)";
break;
+ case 0x924:
+ type = "Cortex-M3 ETM";
+ full = "(Embedded Trace)";
+ break;
+ case 0x925:
+ type = "Cortex-M4 ETM";
+ full = "(Embedded Trace)";
+ break;
+ case 0x930:
+ type = "Cortex-R4 ETM";
+ full = "(Embedded Trace)";
+ break;
+ case 0x9a1:
+ type = "Cortex-M4 TPUI";
+ full = "(Trace Port Interface Unit)";
+ break;
case 0xc08:
type = "Cortex-A8 Debug";
full = "(Debug Unit)";
}
command_print(cmd_ctx, "\t\tPart is %s %s",
type, full);
- }
- else
- {
+ } else {
if (romentry)
command_print(cmd_ctx, "\t\tComponent not present");
else
}
entry_offset += 4;
} while (romentry > 0);
- }
- else
- {
+ } else
command_print(cmd_ctx, "\tNo ROM table present");
- }
- dap_ap_select(swjdp, apselold);
+ dap_ap_select(dap, ap_old);
return ERROR_OK;
}
-DAP_COMMAND_HANDLER(dap_baseaddr_command)
+COMMAND_HANDLER(handle_dap_info_command)
+{
+ struct target *target = get_current_target(CMD_CTX);
+ struct arm *arm = target_to_arm(target);
+ struct adiv5_dap *dap = arm->dap;
+ uint32_t apsel;
+
+ switch (CMD_ARGC) {
+ case 0:
+ apsel = dap->apsel;
+ break;
+ case 1:
+ COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], apsel);
+ break;
+ default:
+ return ERROR_COMMAND_SYNTAX_ERROR;
+ }
+
+ return dap_info_command(CMD_CTX, dap, apsel);
+}
+
+COMMAND_HANDLER(dap_baseaddr_command)
{
- uint32_t apsel, apselsave, baseaddr;
+ struct target *target = get_current_target(CMD_CTX);
+ struct arm *arm = target_to_arm(target);
+ struct adiv5_dap *dap = arm->dap;
+
+ uint32_t apsel, baseaddr;
int retval;
- apselsave = swjdp->apsel;
switch (CMD_ARGC) {
case 0:
- apsel = swjdp->apsel;
+ apsel = dap->apsel;
break;
case 1:
COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], apsel);
/* AP address is in bits 31:24 of DP_SELECT */
if (apsel >= 256)
- return ERROR_INVALID_ARGUMENTS;
+ return ERROR_COMMAND_SYNTAX_ERROR;
break;
default:
return ERROR_COMMAND_SYNTAX_ERROR;
}
- if (apselsave != apsel)
- dap_ap_select(swjdp, apsel);
+ dap_ap_select(dap, apsel);
/* NOTE: assumes we're talking to a MEM-AP, which
* has a base address. There are other kinds of AP,
* though they're not common for now. This should
* use the ID register to verify it's a MEM-AP.
*/
- dap_ap_read_reg_u32(swjdp, AP_REG_BASE, &baseaddr);
- retval = jtagdp_transaction_endcheck(swjdp);
- command_print(CMD_CTX, "0x%8.8" PRIx32, baseaddr);
+ retval = dap_queue_ap_read(dap, AP_REG_BASE, &baseaddr);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ return retval;
- if (apselsave != apsel)
- dap_ap_select(swjdp, apselsave);
+ command_print(CMD_CTX, "0x%8.8" PRIx32, baseaddr);
return retval;
}
-DAP_COMMAND_HANDLER(dap_memaccess_command)
+COMMAND_HANDLER(dap_memaccess_command)
{
+ struct target *target = get_current_target(CMD_CTX);
+ struct arm *arm = target_to_arm(target);
+ struct adiv5_dap *dap = arm->dap;
+
uint32_t memaccess_tck;
switch (CMD_ARGC) {
case 0:
- memaccess_tck = swjdp->memaccess_tck;
+ memaccess_tck = dap->memaccess_tck;
break;
case 1:
COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], memaccess_tck);
default:
return ERROR_COMMAND_SYNTAX_ERROR;
}
- swjdp->memaccess_tck = memaccess_tck;
+ dap->memaccess_tck = memaccess_tck;
command_print(CMD_CTX, "memory bus access delay set to %" PRIi32 " tck",
- swjdp->memaccess_tck);
+ dap->memaccess_tck);
return ERROR_OK;
}
-DAP_COMMAND_HANDLER(dap_apsel_command)
+COMMAND_HANDLER(dap_apsel_command)
{
+ struct target *target = get_current_target(CMD_CTX);
+ struct arm *arm = target_to_arm(target);
+ struct adiv5_dap *dap = arm->dap;
+
uint32_t apsel, apid;
int retval;
COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], apsel);
/* AP address is in bits 31:24 of DP_SELECT */
if (apsel >= 256)
- return ERROR_INVALID_ARGUMENTS;
+ return ERROR_COMMAND_SYNTAX_ERROR;
break;
default:
return ERROR_COMMAND_SYNTAX_ERROR;
}
- dap_ap_select(swjdp, apsel);
- dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &apid);
- retval = jtagdp_transaction_endcheck(swjdp);
+ dap->apsel = apsel;
+ dap_ap_select(dap, apsel);
+
+ retval = dap_queue_ap_read(dap, AP_REG_IDR, &apid);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
command_print(CMD_CTX, "ap %" PRIi32 " selected, identification register 0x%8.8" PRIx32,
apsel, apid);
return retval;
}
-DAP_COMMAND_HANDLER(dap_apid_command)
+COMMAND_HANDLER(dap_apid_command)
{
- uint32_t apsel, apselsave, apid;
+ struct target *target = get_current_target(CMD_CTX);
+ struct arm *arm = target_to_arm(target);
+ struct adiv5_dap *dap = arm->dap;
+
+ uint32_t apsel, apid;
int retval;
- apselsave = swjdp->apsel;
switch (CMD_ARGC) {
case 0:
- apsel = swjdp->apsel;
+ apsel = dap->apsel;
break;
case 1:
COMMAND_PARSE_NUMBER(u32, CMD_ARGV[0], apsel);
/* AP address is in bits 31:24 of DP_SELECT */
if (apsel >= 256)
- return ERROR_INVALID_ARGUMENTS;
+ return ERROR_COMMAND_SYNTAX_ERROR;
break;
default:
return ERROR_COMMAND_SYNTAX_ERROR;
}
- if (apselsave != apsel)
- dap_ap_select(swjdp, apsel);
+ dap_ap_select(dap, apsel);
+
+ retval = dap_queue_ap_read(dap, AP_REG_IDR, &apid);
+ if (retval != ERROR_OK)
+ return retval;
+ retval = dap_run(dap);
+ if (retval != ERROR_OK)
+ return retval;
- dap_ap_read_reg_u32(swjdp, AP_REG_IDR, &apid);
- retval = jtagdp_transaction_endcheck(swjdp);
command_print(CMD_CTX, "0x%8.8" PRIx32, apid);
- if (apselsave != apsel)
- dap_ap_select(swjdp, apselsave);
return retval;
}
+
+static const struct command_registration dap_commands[] = {
+ {
+ .name = "info",
+ .handler = handle_dap_info_command,
+ .mode = COMMAND_EXEC,
+ .help = "display ROM table for MEM-AP "
+ "(default currently selected AP)",
+ .usage = "[ap_num]",
+ },
+ {
+ .name = "apsel",
+ .handler = dap_apsel_command,
+ .mode = COMMAND_EXEC,
+ .help = "Set the currently selected AP (default 0) "
+ "and display the result",
+ .usage = "[ap_num]",
+ },
+ {
+ .name = "apid",
+ .handler = dap_apid_command,
+ .mode = COMMAND_EXEC,
+ .help = "return ID register from AP "
+ "(default currently selected AP)",
+ .usage = "[ap_num]",
+ },
+ {
+ .name = "baseaddr",
+ .handler = dap_baseaddr_command,
+ .mode = COMMAND_EXEC,
+ .help = "return debug base address from MEM-AP "
+ "(default currently selected AP)",
+ .usage = "[ap_num]",
+ },
+ {
+ .name = "memaccess",
+ .handler = dap_memaccess_command,
+ .mode = COMMAND_EXEC,
+ .help = "set/get number of extra tck for MEM-AP memory "
+ "bus access [0-255]",
+ .usage = "[cycles]",
+ },
+ COMMAND_REGISTRATION_DONE
+};
+
+const struct command_registration dap_command_handlers[] = {
+ {
+ .name = "dap",
+ .mode = COMMAND_EXEC,
+ .help = "DAP command group",
+ .usage = "",
+ .chain = dap_commands,
+ },
+ COMMAND_REGISTRATION_DONE
+};
Code Review / openocd.git / blobdiff