Remove FSF address from GPL notices

[openocd.git] / src / jtag / jtag.h

diff --git a/src/jtag/jtag.h b/src/jtag/jtag.h
index da5e025f65f68564bed24846e63fadf064ae1884..d3fa449247d86ddef95014dbd3356e8fcd905820 100644 (file)
--- a/src/jtag/jtag.h
+++ b/src/jtag/jtag.h
@@ -16,9 +16,7 @@
 *   GNU General Public License for more details.                          *
 *                                                                         *
 *   You should have received a copy of the GNU General Public License     *
-*   along with this program; if not, write to the                         *
-*   Free Software Foundation, Inc.,                                       *
-*   59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.             *
+*   along with this program.  If not, see <http://www.gnu.org/licenses/>. *
 ***************************************************************************/
 
 #ifndef JTAG_H
@@ -107,7 +105,7 @@ extern tap_state_t cmd_queue_cur_state;
  * jtag_add_dr_scan_check() to validate the value that was scanned out.
  */
 struct scan_field {
-       /** The number of bits this field specifies (up to 32) */
+       /** The number of bits this field specifies */
        int num_bits;
        /** A pointer to value to be scanned into the device */
        const uint8_t *out_value;
@@ -121,9 +119,9 @@ struct scan_field {
 };
 
 struct jtag_tap {
-       const char *chip;
-       const char *tapname;
-       const char *dotted_name;
+       char *chip;
+       char *tapname;
+       char *dotted_name;
        int abs_chain_position;
        /** Is this TAP disabled after JTAG reset? */
        bool disabled_after_reset;
@@ -266,6 +264,7 @@ enum reset_types {
        RESET_TRST_OPEN_DRAIN = 0x10,
        RESET_SRST_PUSH_PULL  = 0x20,
        RESET_SRST_NO_GATING  = 0x40,
+       RESET_CNCT_UNDER_SRST = 0x80
 };
 
 enum reset_types jtag_get_reset_config(void);
@@ -608,33 +607,6 @@ void jtag_sleep(uint32_t us);
 #define ERROR_JTAG_TRANSITION_INVALID (-109)
 #define ERROR_JTAG_INIT_SOFT_FAIL    (-110)
 
-/**
- * jtag_add_dr_out() is a version of jtag_add_dr_scan() which
- * only scans data out. It operates on 32 bit integers instead
- * of 8 bit, which makes it a better impedance match with
- * the calling code which often operate on 32 bit integers.
- *
- * Current or end_state can not be TAP_RESET. end_state can be TAP_INVALID
- *
- * num_bits[i] is the number of bits to clock out from value[i] LSB first.
- *
- * If the device is in bypass, then that is an error condition in
- * the caller code that is not detected by this fn, whereas
- * jtag_add_dr_scan() does detect it. Similarly if the device is not in
- * bypass, data must be passed to it.
- *
- * If anything fails, then jtag_error will be set and jtag_execute() will
- * return an error. There is no way to determine if there was a failure
- * during this function call.
- *
- * This is an inline fn to speed up embedded hosts. Also note that
- * interface_jtag_add_dr_out() can be a *small* inline function for
- * embedded hosts.
- *
- * There is no jtag_add_dr_outin() version of this fn that also allows
- * clocking data back in. Patches gladly accepted!
- */
-
 /**
  * Set the current JTAG core execution error, unless one was set
  * by a previous call previously.  Driver or application code must