/* project specific includes */
#include <helper/binarybuffer.h>
+#include <helper/bits.h>
#include <jtag/interface.h>
#include <jtag/hla/hla_layout.h>
#include <jtag/hla/hla_transport.h>
#include <jtag/hla/hla_interface.h>
#include <target/target.h>
+#include <transport/transport.h>
#include <target/cortex_m.h>
/*
* ST-Link/V1, ST-Link/V2 and ST-Link/V2.1 are full-speed USB devices and
* this limits the bulk packet size and the 8bit read/writes to max 64 bytes.
- * STLINK-V3 is a high speed USB 2.0 and the limit is 512 bytes.
+ * STLINK-V3 is a high speed USB 2.0 and the limit is 512 bytes from FW V3J6.
*/
#define STLINK_MAX_RW8 (64)
#define STLINKV3_MAX_RW8 (512)
#define STLINK_SWD_AP_FAULT 0x11
#define STLINK_SWD_AP_ERROR 0x12
#define STLINK_SWD_AP_PARITY_ERROR 0x13
+#define STLINK_JTAG_GET_IDCODE_ERROR 0x09
#define STLINK_JTAG_WRITE_ERROR 0x0c
#define STLINK_JTAG_WRITE_VERIF_ERROR 0x0d
#define STLINK_SWD_DP_WAIT 0x14
#define STLINK_SWD_AP_STICKY_ERROR 0x19
#define STLINK_SWD_AP_STICKYORUN_ERROR 0x1a
+#define STLINK_BAD_AP_ERROR 0x1d
+
#define STLINK_CORE_RUNNING 0x80
#define STLINK_CORE_HALTED 0x81
#define STLINK_CORE_STAT_UNKNOWN -1
#define STLINK_DEBUG_APIV2_GET_TRACE_NB 0x42
#define STLINK_DEBUG_APIV2_SWD_SET_FREQ 0x43
#define STLINK_DEBUG_APIV2_JTAG_SET_FREQ 0x44
-
+#define STLINK_DEBUG_APIV2_READ_DAP_REG 0x45
+#define STLINK_DEBUG_APIV2_WRITE_DAP_REG 0x46
#define STLINK_DEBUG_APIV2_READMEM_16BIT 0x47
#define STLINK_DEBUG_APIV2_WRITEMEM_16BIT 0x48
+#define STLINK_DEBUG_APIV2_INIT_AP 0x4B
+#define STLINK_DEBUG_APIV2_CLOSE_AP_DBG 0x4C
+
#define STLINK_APIV3_SET_COM_FREQ 0x61
#define STLINK_APIV3_GET_COM_FREQ 0x62
#define STLINK_DEBUG_APIV2_DRIVE_NRST_HIGH 0x01
#define STLINK_DEBUG_APIV2_DRIVE_NRST_PULSE 0x02
+#define STLINK_DEBUG_PORT_ACCESS 0xffff
+
#define STLINK_TRACE_SIZE 4096
#define STLINK_TRACE_MAX_HZ 2000000
* Map the relevant features, quirks and workaround for specific firmware
* version of stlink
*/
-#define STLINK_F_HAS_TRACE (1UL << 0)
-#define STLINK_F_HAS_SWD_SET_FREQ (1UL << 1)
-#define STLINK_F_HAS_JTAG_SET_FREQ (1UL << 2)
-#define STLINK_F_HAS_MEM_16BIT (1UL << 3)
-#define STLINK_F_HAS_GETLASTRWSTATUS2 (1UL << 4)
+#define STLINK_F_HAS_TRACE BIT(0)
+#define STLINK_F_HAS_SWD_SET_FREQ BIT(1)
+#define STLINK_F_HAS_JTAG_SET_FREQ BIT(2)
+#define STLINK_F_HAS_MEM_16BIT BIT(3)
+#define STLINK_F_HAS_GETLASTRWSTATUS2 BIT(4)
+#define STLINK_F_HAS_DAP_REG BIT(5)
+#define STLINK_F_QUIRK_JTAG_DP_READ BIT(6)
+#define STLINK_F_HAS_AP_INIT BIT(7)
+#define STLINK_F_HAS_DPBANKSEL BIT(8)
+#define STLINK_F_HAS_RW8_512BYTES BIT(9)
/* aliases */
#define STLINK_F_HAS_TARGET_VOLT STLINK_F_HAS_TRACE
static void stlink_usb_init_buffer(void *handle, uint8_t direction, uint32_t size);
static int stlink_swim_status(void *handle);
+void stlink_dump_speed_map(const struct speed_map *map, unsigned int map_size);
+static int stlink_get_com_freq(void *handle, bool is_jtag, struct speed_map *map);
+static int stlink_speed(void *handle, int khz, bool query);
/** */
static unsigned int stlink_usb_block(void *handle)
assert(handle != NULL);
- if (h->version.stlink == 3)
+ if (h->version.flags & STLINK_F_HAS_RW8_512BYTES)
return STLINKV3_MAX_RW8;
else
return STLINK_MAX_RW8;
static int stlink_usb_xfer_v1_get_status(void *handle)
{
struct stlink_usb_handle_s *h = handle;
+ int tr, ret;
assert(handle != NULL);
/* read status */
memset(h->cmdbuf, 0, STLINK_SG_SIZE);
- if (jtag_libusb_bulk_read(h->fd, h->rx_ep, (char *)h->cmdbuf,
- 13, STLINK_READ_TIMEOUT) != 13)
+ ret = jtag_libusb_bulk_read(h->fd, h->rx_ep, (char *)h->cmdbuf, 13,
+ STLINK_READ_TIMEOUT, &tr);
+ if (ret || tr != 13)
return ERROR_FAIL;
uint32_t t1;
static int stlink_usb_xfer_rw(void *handle, int cmdsize, const uint8_t *buf, int size)
{
struct stlink_usb_handle_s *h = handle;
+ int tr, ret;
assert(handle != NULL);
- if (jtag_libusb_bulk_write(h->fd, h->tx_ep, (char *)h->cmdbuf, cmdsize,
- STLINK_WRITE_TIMEOUT) != cmdsize) {
+ ret = jtag_libusb_bulk_write(h->fd, h->tx_ep, (char *)h->cmdbuf,
+ cmdsize, STLINK_WRITE_TIMEOUT, &tr);
+ if (ret || tr != cmdsize)
return ERROR_FAIL;
- }
if (h->direction == h->tx_ep && size) {
- if (jtag_libusb_bulk_write(h->fd, h->tx_ep, (char *)buf,
- size, STLINK_WRITE_TIMEOUT) != size) {
+ ret = jtag_libusb_bulk_write(h->fd, h->tx_ep, (char *)buf,
+ size, STLINK_WRITE_TIMEOUT, &tr);
+ if (ret || tr != size) {
LOG_DEBUG("bulk write failed");
return ERROR_FAIL;
}
} else if (h->direction == h->rx_ep && size) {
- if (jtag_libusb_bulk_read(h->fd, h->rx_ep, (char *)buf,
- size, STLINK_READ_TIMEOUT) != size) {
+ ret = jtag_libusb_bulk_read(h->fd, h->rx_ep, (char *)buf,
+ size, STLINK_READ_TIMEOUT, &tr);
+ if (ret || tr != size) {
LOG_DEBUG("bulk read failed");
return ERROR_FAIL;
}
transfers block in cmdbuf
<size> indicates number of bytes in the following
data phase.
+ Ignore the (eventual) error code in the received packet.
*/
-static int stlink_usb_xfer(void *handle, const uint8_t *buf, int size)
+static int stlink_usb_xfer_noerrcheck(void *handle, const uint8_t *buf, int size)
{
int err, cmdsize = STLINK_CMD_SIZE_V2;
struct stlink_usb_handle_s *h = handle;
case STLINK_SWD_DP_WAIT:
LOG_DEBUG("wait status SWD_DP_WAIT (0x%x)", STLINK_SWD_DP_WAIT);
return ERROR_WAIT;
+ case STLINK_JTAG_GET_IDCODE_ERROR:
+ LOG_DEBUG("STLINK_JTAG_GET_IDCODE_ERROR");
+ return ERROR_FAIL;
case STLINK_JTAG_WRITE_ERROR:
LOG_DEBUG("Write error");
return ERROR_FAIL;
case STLINK_SWD_AP_STICKYORUN_ERROR:
LOG_DEBUG("STLINK_SWD_AP_STICKYORUN_ERROR");
return ERROR_FAIL;
+ case STLINK_BAD_AP_ERROR:
+ LOG_DEBUG("STLINK_BAD_AP_ERROR");
+ return ERROR_FAIL;
default:
LOG_DEBUG("unknown/unexpected STLINK status code 0x%x", h->databuf[0]);
return ERROR_FAIL;
}
}
+/*
+ * Wrapper around stlink_usb_xfer_noerrcheck()
+ * to check the error code in the received packet
+ */
+static int stlink_usb_xfer_errcheck(void *handle, const uint8_t *buf, int size)
+{
+ int retval;
+
+ assert(size > 0);
+
+ retval = stlink_usb_xfer_noerrcheck(handle, buf, size);
+ if (retval != ERROR_OK)
+ return retval;
+
+ return stlink_usb_error_check(handle);
+}
/** Issue an STLINK command via USB transfer, with retries on any wait status responses.
while (1) {
if ((h->transport != HL_TRANSPORT_SWIM) || !retries) {
- res = stlink_usb_xfer(handle, buf, size);
+ res = stlink_usb_xfer_noerrcheck(handle, buf, size);
if (res != ERROR_OK)
return res;
}
static int stlink_usb_read_trace(void *handle, const uint8_t *buf, int size)
{
struct stlink_usb_handle_s *h = handle;
+ int tr, ret;
assert(handle != NULL);
assert(h->version.flags & STLINK_F_HAS_TRACE);
- if (jtag_libusb_bulk_read(h->fd, h->trace_ep, (char *)buf,
- size, STLINK_READ_TIMEOUT) != size) {
+ ret = jtag_libusb_bulk_read(h->fd, h->trace_ep, (char *)buf, size,
+ STLINK_READ_TIMEOUT, &tr);
+ if (ret || tr != size) {
LOG_ERROR("bulk trace read failed");
return ERROR_FAIL;
}
h->cmdbuf[h->cmdidx++] = STLINK_GET_VERSION;
- res = stlink_usb_xfer(handle, h->databuf, 6);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, 6);
if (res != ERROR_OK)
return res;
h->cmdbuf[h->cmdidx++] = STLINK_APIV3_GET_VERSION_EX;
- res = stlink_usb_xfer(handle, h->databuf, 12);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, 12);
if (res != ERROR_OK)
return res;
flags |= STLINK_F_HAS_SWD_SET_FREQ;
/* API to set JTAG frequency from J24 */
- if (h->version.jtag >= 24)
+ /* API to access DAP registers from J24 */
+ if (h->version.jtag >= 24) {
flags |= STLINK_F_HAS_JTAG_SET_FREQ;
+ flags |= STLINK_F_HAS_DAP_REG;
+ }
+
+ /* Quirk for read DP in JTAG mode (V2 only) from J24, fixed in J32 */
+ if (h->version.jtag >= 24 && h->version.jtag < 32)
+ flags |= STLINK_F_QUIRK_JTAG_DP_READ;
/* API to read/write memory at 16 bit from J26 */
if (h->version.jtag >= 26)
flags |= STLINK_F_HAS_MEM_16BIT;
+ /* API required to init AP before any AP access from J28 */
+ if (h->version.jtag >= 28)
+ flags |= STLINK_F_HAS_AP_INIT;
+
+ /* Banked regs (DPv1 & DPv2) support from V2J32 */
+ if (h->version.jtag >= 32)
+ flags |= STLINK_F_HAS_DPBANKSEL;
+
break;
case 3:
/* all STLINK-V3 use api-v3 */
/* preferred API to get last R/W status */
flags |= STLINK_F_HAS_GETLASTRWSTATUS2;
+ /* API to access DAP registers */
+ flags |= STLINK_F_HAS_DAP_REG;
+
/* API to read/write memory at 16 bit */
flags |= STLINK_F_HAS_MEM_16BIT;
+ /* API required to init AP before any AP access */
+ flags |= STLINK_F_HAS_AP_INIT;
+
+ /* Banked regs (DPv1 & DPv2) support from V3J2 */
+ if (h->version.jtag >= 2)
+ flags |= STLINK_F_HAS_DPBANKSEL;
+
+ /* 8bit read/write max packet size 512 bytes from V3J6 */
+ if (h->version.jtag >= 6)
+ flags |= STLINK_F_HAS_RW8_512BYTES;
+
break;
default:
break;
if (bridge)
p += sprintf(p, "B%d", bridge);
if (swim || !msd)
- p += sprintf(p, "S%d", swim);
+ sprintf(p, "S%d", swim);
LOG_INFO("STLINK %s (API v%d) VID:PID %04X:%04X",
v_str,
h->cmdbuf[h->cmdidx++] = STLINK_GET_TARGET_VOLTAGE;
- int result = stlink_usb_xfer(handle, h->databuf, 8);
+ int result = stlink_usb_xfer_noerrcheck(handle, h->databuf, 8);
if (result != ERROR_OK)
return result;
h->cmdbuf[h->cmdidx++] = STLINK_GET_CURRENT_MODE;
- res = stlink_usb_xfer(handle, h->databuf, 2);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, 2);
if (res != ERROR_OK)
return res;
return ERROR_FAIL;
}
- res = stlink_usb_xfer(handle, 0, 0);
+ res = stlink_usb_xfer_noerrcheck(handle, 0, 0);
if (res != ERROR_OK)
return res;
}
/** */
-static int stlink_usb_init_mode(void *handle, bool connect_under_reset)
+static int stlink_usb_init_mode(void *handle, bool connect_under_reset, int initial_interface_speed)
{
int res;
uint8_t mode;
return ERROR_FAIL;
}
+ /* set the speed before entering the mode, as the chip discovery phase should be done at this speed too */
+ if (h->transport == HL_TRANSPORT_JTAG) {
+ if (h->version.flags & STLINK_F_HAS_JTAG_SET_FREQ) {
+ stlink_dump_speed_map(stlink_khz_to_speed_map_jtag, ARRAY_SIZE(stlink_khz_to_speed_map_jtag));
+ stlink_speed(h, initial_interface_speed, false);
+ }
+ } else if (h->transport == HL_TRANSPORT_SWD) {
+ if (h->version.flags & STLINK_F_HAS_SWD_SET_FREQ) {
+ stlink_dump_speed_map(stlink_khz_to_speed_map_swd, ARRAY_SIZE(stlink_khz_to_speed_map_swd));
+ stlink_speed(h, initial_interface_speed, false);
+ }
+ }
+
+ if (h->version.jtag_api == STLINK_JTAG_API_V3) {
+ struct speed_map map[STLINK_V3_MAX_FREQ_NB];
+
+ stlink_get_com_freq(h, (h->transport == HL_TRANSPORT_JTAG), map);
+ stlink_dump_speed_map(map, ARRAY_SIZE(map));
+ stlink_speed(h, initial_interface_speed, false);
+ }
+
/* preliminary SRST assert:
* We want SRST is asserted before activating debug signals (mode_enter).
* As the required mode has not been set, the adapter may not know what pin to use.
stlink_usb_init_buffer(handle, h->rx_ep, 4);
h->cmdbuf[h->cmdidx++] = STLINK_SWIM_COMMAND;
h->cmdbuf[h->cmdidx++] = STLINK_SWIM_READSTATUS;
- res = stlink_usb_xfer(handle, h->databuf, 4);
+ /* error is checked by the caller */
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, 4);
if (res != ERROR_OK)
return res;
return ERROR_OK;
h->cmdbuf[h->cmdidx++] = STLINK_SWIM_COMMAND;
h->cmdbuf[h->cmdidx++] = STLINK_SWIM_READ_CAP;
h->cmdbuf[h->cmdidx++] = 0x01;
- res = stlink_usb_xfer(handle, h->databuf, 8);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, 8);
if (res != ERROR_OK)
return res;
memcpy(cap, h->databuf, 8);
stlink_usb_init_buffer(handle, h->rx_ep, len);
h->cmdbuf[h->cmdidx++] = STLINK_SWIM_COMMAND;
h->cmdbuf[h->cmdidx++] = STLINK_SWIM_READBUF;
- res = stlink_usb_xfer(handle, data, len);
+ res = stlink_usb_xfer_noerrcheck(handle, data, len);
if (res != ERROR_OK)
return res;
/** */
static int stlink_usb_idcode(void *handle, uint32_t *idcode)
{
- int res;
+ int res, offset;
struct stlink_usb_handle_s *h = handle;
assert(handle != NULL);
return ERROR_OK;
}
- stlink_usb_init_buffer(handle, h->rx_ep, 4);
+ stlink_usb_init_buffer(handle, h->rx_ep, 12);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
- h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_READCOREID;
+ if (h->version.jtag_api == STLINK_JTAG_API_V1) {
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_READCOREID;
- res = stlink_usb_xfer(handle, h->databuf, 4);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, 4);
+ offset = 0;
+ } else {
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_READ_IDCODES;
+
+ res = stlink_usb_xfer_errcheck(handle, h->databuf, 12);
+ offset = 4;
+ }
if (res != ERROR_OK)
return res;
- *idcode = le_to_h_u32(h->databuf);
+ *idcode = le_to_h_u32(h->databuf + offset);
LOG_DEBUG("IDCODE: 0x%08" PRIX32, *idcode);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_GET_TRACE_NB;
- res = stlink_usb_xfer(handle, h->databuf, 2);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, 2);
if (res != ERROR_OK)
return res;
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_GETSTATUS;
- res = stlink_usb_xfer(handle, h->databuf, 2);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, 2);
if (res != ERROR_OK)
return TARGET_UNKNOWN;
stlink_usb_init_buffer(handle, h->rx_ep, 2);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_STOP_TRACE_RX;
- res = stlink_usb_xfer(handle, h->databuf, 2);
+ res = stlink_usb_xfer_errcheck(handle, h->databuf, 2);
if (res == ERROR_OK)
h->trace.enabled = false;
h_u32_to_le(h->cmdbuf+h->cmdidx, h->trace.source_hz);
h->cmdidx += 4;
- res = stlink_usb_xfer(handle, h->databuf, 2);
+ res = stlink_usb_xfer_errcheck(handle, h->databuf, 2);
if (res == ERROR_OK) {
h->trace.enabled = true;
assert(handle != NULL);
- stlink_usb_init_buffer(handle, h->rx_ep, 84);
+ stlink_usb_init_buffer(handle, h->rx_ep, 88);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
- if (h->version.jtag_api == STLINK_JTAG_API_V1)
+ if (h->version.jtag_api == STLINK_JTAG_API_V1) {
+
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV1_READALLREGS;
- else
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, 84);
+ /* regs data from offset 0 */
+ } else {
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_READALLREGS;
+ res = stlink_usb_xfer_errcheck(handle, h->databuf, 88);
+ /* status at offset 0, regs data from offset 4 */
+ }
- res = stlink_usb_xfer(handle, h->databuf, 84);
-
- if (res != ERROR_OK)
- return res;
-
- return ERROR_OK;
+ return res;
}
/** */
h->cmdbuf[h->cmdidx++] = num;
if (h->version.jtag_api == STLINK_JTAG_API_V1) {
- res = stlink_usb_xfer(handle, h->databuf, 4);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, 4);
if (res != ERROR_OK)
return res;
*val = le_to_h_u32(h->databuf);
static int stlink_usb_get_rw_status(void *handle)
{
- int res;
struct stlink_usb_handle_s *h = handle;
assert(handle != NULL);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
if (h->version.flags & STLINK_F_HAS_GETLASTRWSTATUS2) {
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_GETLASTRWSTATUS2;
-
- res = stlink_usb_xfer(handle, h->databuf, 12);
+ return stlink_usb_xfer_errcheck(handle, h->databuf, 12);
} else {
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_GETLASTRWSTATUS;
-
- res = stlink_usb_xfer(handle, h->databuf, 2);
+ return stlink_usb_xfer_errcheck(handle, h->databuf, 2);
}
-
- if (res != ERROR_OK)
- return res;
-
- return stlink_usb_error_check(h);
}
/** */
if (read_len == 1)
read_len++;
- res = stlink_usb_xfer(handle, h->databuf, read_len);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, read_len);
if (res != ERROR_OK)
return res;
h_u16_to_le(h->cmdbuf+h->cmdidx, len);
h->cmdidx += 2;
- res = stlink_usb_xfer(handle, buffer, len);
+ res = stlink_usb_xfer_noerrcheck(handle, buffer, len);
if (res != ERROR_OK)
return res;
h_u16_to_le(h->cmdbuf+h->cmdidx, len);
h->cmdidx += 2;
- res = stlink_usb_xfer(handle, h->databuf, len);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, len);
if (res != ERROR_OK)
return res;
h_u16_to_le(h->cmdbuf+h->cmdidx, len);
h->cmdidx += 2;
- res = stlink_usb_xfer(handle, buffer, len);
+ res = stlink_usb_xfer_noerrcheck(handle, buffer, len);
if (res != ERROR_OK)
return res;
h_u16_to_le(h->cmdbuf+h->cmdidx, len);
h->cmdidx += 2;
- res = stlink_usb_xfer(handle, h->databuf, len);
+ res = stlink_usb_xfer_noerrcheck(handle, h->databuf, len);
if (res != ERROR_OK)
return res;
h_u16_to_le(h->cmdbuf+h->cmdidx, len);
h->cmdidx += 2;
- res = stlink_usb_xfer(handle, buffer, len);
+ res = stlink_usb_xfer_noerrcheck(handle, buffer, len);
if (res != ERROR_OK)
return res;
h->cmdbuf[h->cmdidx++] = STLINK_APIV3_GET_COM_FREQ;
h->cmdbuf[h->cmdidx++] = is_jtag ? 1 : 0;
- int res = stlink_usb_xfer(handle, h->databuf, 52);
+ int res = stlink_usb_xfer_errcheck(handle, h->databuf, 52);
int size = h->databuf[8];
h_u32_to_le(&h->cmdbuf[4], frequency);
- return stlink_usb_xfer(handle, h->databuf, 8);
+ return stlink_usb_xfer_errcheck(handle, h->databuf, 8);
}
static int stlink_speed_v3(void *handle, bool is_jtag, int khz, bool query)
}
/* initialize the debug hardware */
- err = stlink_usb_init_mode(h, param->connect_under_reset);
+ err = stlink_usb_init_mode(h, param->connect_under_reset, param->initial_interface_speed);
if (err != ERROR_OK) {
LOG_ERROR("init mode failed (unable to connect to the target)");
return ERROR_OK;
}
- if (h->transport == HL_TRANSPORT_JTAG) {
- if (h->version.flags & STLINK_F_HAS_JTAG_SET_FREQ) {
- stlink_dump_speed_map(stlink_khz_to_speed_map_jtag, ARRAY_SIZE(stlink_khz_to_speed_map_jtag));
- stlink_speed(h, param->initial_interface_speed, false);
- }
- } else if (h->transport == HL_TRANSPORT_SWD) {
- if (h->version.flags & STLINK_F_HAS_SWD_SET_FREQ) {
- stlink_dump_speed_map(stlink_khz_to_speed_map_swd, ARRAY_SIZE(stlink_khz_to_speed_map_swd));
- stlink_speed(h, param->initial_interface_speed, false);
- }
- }
-
- if (h->version.jtag_api == STLINK_JTAG_API_V3) {
- struct speed_map map[STLINK_V3_MAX_FREQ_NB];
-
- stlink_get_com_freq(h, (h->transport == HL_TRANSPORT_JTAG), map);
- stlink_dump_speed_map(map, ARRAY_SIZE(map));
- stlink_speed(h, param->initial_interface_speed, false);
- }
-
/* get cpuid, so we can determine the max page size
* start with a safe default */
h->max_mem_packet = (1 << 10);
return ERROR_FAIL;
}
-int stlink_config_trace(void *handle, bool enabled, enum tpiu_pin_protocol pin_protocol,
- uint32_t port_size, unsigned int *trace_freq)
+int stlink_config_trace(void *handle, bool enabled,
+ enum tpiu_pin_protocol pin_protocol, uint32_t port_size,
+ unsigned int *trace_freq, unsigned int traceclkin_freq,
+ uint16_t *prescaler)
{
struct stlink_usb_handle_s *h = handle;
+ uint16_t presc;
if (enabled && (!(h->version.flags & STLINK_F_HAS_TRACE) ||
pin_protocol != TPIU_PIN_PROTOCOL_ASYNC_UART)) {
if (!*trace_freq)
*trace_freq = STLINK_TRACE_MAX_HZ;
+
+ presc = traceclkin_freq / *trace_freq;
+
+ if (traceclkin_freq % *trace_freq > 0)
+ presc++;
+
+ if (presc > TPIU_ACPR_MAX_SWOSCALER) {
+ LOG_ERROR("SWO frequency is not suitable. Please choose a different "
+ "frequency.");
+ return ERROR_FAIL;
+ }
+
+ *prescaler = presc;
h->trace.source_hz = *trace_freq;
return stlink_usb_trace_enable(h);
}
+/** */
+static int stlink_usb_init_access_port(void *handle, unsigned char ap_num)
+{
+ struct stlink_usb_handle_s *h = handle;
+
+ assert(handle != NULL);
+
+ if (!(h->version.flags & STLINK_F_HAS_AP_INIT))
+ return ERROR_COMMAND_NOTFOUND;
+
+ LOG_DEBUG_IO("init ap_num = %d", ap_num);
+ stlink_usb_init_buffer(handle, h->rx_ep, 16);
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_INIT_AP;
+ h->cmdbuf[h->cmdidx++] = ap_num;
+
+ return stlink_usb_xfer_errcheck(handle, h->databuf, 2);
+}
+
+/** */
+static int stlink_usb_close_access_port(void *handle, unsigned char ap_num)
+{
+ struct stlink_usb_handle_s *h = handle;
+
+ assert(handle != NULL);
+
+ if (!(h->version.flags & STLINK_F_HAS_AP_INIT))
+ return ERROR_COMMAND_NOTFOUND;
+
+ LOG_DEBUG_IO("close ap_num = %d", ap_num);
+ stlink_usb_init_buffer(handle, h->rx_ep, 16);
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_CLOSE_AP_DBG;
+ h->cmdbuf[h->cmdidx++] = ap_num;
+
+ return stlink_usb_xfer_errcheck(handle, h->databuf, 2);
+}
+
+/** */
+static int stlink_read_dap_register(void *handle, unsigned short dap_port,
+ unsigned short addr, uint32_t *val)
+{
+ struct stlink_usb_handle_s *h = handle;
+ int retval;
+
+ assert(handle != NULL);
+
+ if (!(h->version.flags & STLINK_F_HAS_DAP_REG))
+ return ERROR_COMMAND_NOTFOUND;
+
+ stlink_usb_init_buffer(handle, h->rx_ep, 16);
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_READ_DAP_REG;
+ h_u16_to_le(&h->cmdbuf[2], dap_port);
+ h_u16_to_le(&h->cmdbuf[4], addr);
+
+ retval = stlink_usb_xfer_errcheck(handle, h->databuf, 8);
+ *val = le_to_h_u32(h->databuf + 4);
+ LOG_DEBUG_IO("dap_port_read = %d, addr = 0x%x, value = 0x%x", dap_port, addr, *val);
+ return retval;
+}
+
+/** */
+static int stlink_write_dap_register(void *handle, unsigned short dap_port,
+ unsigned short addr, uint32_t val)
+{
+ struct stlink_usb_handle_s *h = handle;
+
+ assert(handle != NULL);
+
+ if (!(h->version.flags & STLINK_F_HAS_DAP_REG))
+ return ERROR_COMMAND_NOTFOUND;
+
+ LOG_DEBUG_IO("dap_write port = %d, addr = 0x%x, value = 0x%x", dap_port, addr, val);
+ stlink_usb_init_buffer(handle, h->rx_ep, 16);
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_WRITE_DAP_REG;
+ h_u16_to_le(&h->cmdbuf[2], dap_port);
+ h_u16_to_le(&h->cmdbuf[4], addr);
+ h_u32_to_le(&h->cmdbuf[6], val);
+ return stlink_usb_xfer_errcheck(handle, h->databuf, 2);
+}
+
/** */
struct hl_layout_api_s stlink_usb_layout_api = {
/** */
/** */
.poll_trace = stlink_usb_trace_read,
};
+
+/*****************************************************************************
+ * DAP direct interface
+ */
+
+static struct stlink_usb_handle_s *stlink_dap_handle;
+static struct hl_interface_param_s stlink_dap_param;
+static DECLARE_BITMAP(opened_ap, DP_APSEL_MAX + 1);
+static int stlink_dap_error = ERROR_OK;
+
+static int stlink_dap_op_queue_dp_read(struct adiv5_dap *dap, unsigned reg,
+ uint32_t *data);
+
+/** */
+static int stlink_dap_record_error(int error)
+{
+ if (stlink_dap_error == ERROR_OK)
+ stlink_dap_error = error;
+ return ERROR_OK;
+}
+
+/** */
+static int stlink_dap_get_and_clear_error(void)
+{
+ int retval = stlink_dap_error;
+ stlink_dap_error = ERROR_OK;
+ return retval;
+}
+
+/** */
+static int stlink_dap_open_ap(unsigned short apsel)
+{
+ int retval;
+
+ /* nothing to do on old versions */
+ if (!(stlink_dap_handle->version.flags & STLINK_F_HAS_AP_INIT))
+ return ERROR_OK;
+
+ if (apsel > DP_APSEL_MAX)
+ return ERROR_FAIL;
+
+ if (test_bit(apsel, opened_ap))
+ return ERROR_OK;
+
+ retval = stlink_usb_init_access_port(stlink_dap_handle, apsel);
+ if (retval != ERROR_OK)
+ return retval;
+
+ LOG_DEBUG("AP %d enabled", apsel);
+ set_bit(apsel, opened_ap);
+ return ERROR_OK;
+}
+
+/** */
+static int stlink_dap_closeall_ap(void)
+{
+ int retval, apsel;
+
+ /* nothing to do on old versions */
+ if (!(stlink_dap_handle->version.flags & STLINK_F_HAS_AP_INIT))
+ return ERROR_OK;
+
+ for (apsel = 0; apsel <= DP_APSEL_MAX; apsel++) {
+ if (!test_bit(apsel, opened_ap))
+ continue;
+ retval = stlink_usb_close_access_port(stlink_dap_handle, apsel);
+ if (retval != ERROR_OK)
+ return retval;
+ clear_bit(apsel, opened_ap);
+ }
+ return ERROR_OK;
+}
+
+/** */
+static int stlink_dap_reinit_interface(void)
+{
+ int retval;
+ enum stlink_mode mode;
+
+ /*
+ * On JTAG only, it should be enough to call stlink_usb_reset(). But on
+ * some firmware version it does not work as expected, and there is no
+ * equivalent for SWD.
+ * At least for now, to reset the interface quit from JTAG/SWD mode then
+ * select the mode again.
+ */
+
+ mode = stlink_get_mode(stlink_dap_param.transport);
+ if (!stlink_dap_handle->reconnect_pending) {
+ stlink_dap_handle->reconnect_pending = true;
+ stlink_usb_mode_leave(stlink_dap_handle, mode);
+ }
+
+ retval = stlink_usb_mode_enter(stlink_dap_handle, mode);
+ if (retval != ERROR_OK)
+ return retval;
+
+ stlink_dap_handle->reconnect_pending = false;
+ /* on new FW, calling mode-leave closes all the opened AP; reopen them! */
+ if (stlink_dap_handle->version.flags & STLINK_F_HAS_AP_INIT)
+ for (int apsel = 0; apsel <= DP_APSEL_MAX; apsel++)
+ if (test_bit(apsel, opened_ap)) {
+ clear_bit(apsel, opened_ap);
+ stlink_dap_open_ap(apsel);
+ }
+ return ERROR_OK;
+}
+
+/** */
+static int stlink_dap_op_connect(struct adiv5_dap *dap)
+{
+ uint32_t idcode;
+ int retval;
+
+ LOG_INFO("stlink_dap_op_connect(%sconnect)", dap->do_reconnect ? "re" : "");
+
+ /* Check if we should reset srst already when connecting, but not if reconnecting. */
+ if (!dap->do_reconnect) {
+ enum reset_types jtag_reset_config = jtag_get_reset_config();
+
+ if (jtag_reset_config & RESET_CNCT_UNDER_SRST) {
+ if (jtag_reset_config & RESET_SRST_NO_GATING)
+ adapter_assert_reset();
+ else
+ LOG_WARNING("\'srst_nogate\' reset_config option is required");
+ }
+ }
+
+ dap->do_reconnect = false;
+ dap_invalidate_cache(dap);
+
+ retval = dap_dp_init(dap);
+ if (retval != ERROR_OK) {
+ dap->do_reconnect = true;
+ return retval;
+ }
+
+ retval = stlink_usb_idcode(stlink_dap_handle, &idcode);
+ if (retval == ERROR_OK)
+ LOG_INFO("%s %#8.8" PRIx32,
+ (stlink_dap_handle->transport == HL_TRANSPORT_JTAG) ? "JTAG IDCODE" : "SWD DPIDR",
+ idcode);
+ else
+ dap->do_reconnect = true;
+
+ return retval;
+}
+
+/** */
+static int stlink_dap_check_reconnect(struct adiv5_dap *dap)
+{
+ int retval;
+
+ if (!dap->do_reconnect)
+ return ERROR_OK;
+
+ retval = stlink_dap_reinit_interface();
+ if (retval != ERROR_OK)
+ return retval;
+
+ return stlink_dap_op_connect(dap);
+}
+
+/** */
+static int stlink_dap_op_send_sequence(struct adiv5_dap *dap, enum swd_special_seq seq)
+{
+ /* Ignore the request */
+ return ERROR_OK;
+}
+
+/** */
+static int stlink_dap_op_queue_dp_read(struct adiv5_dap *dap, unsigned reg,
+ uint32_t *data)
+{
+ uint32_t dummy;
+ int retval;
+
+ if (!(stlink_dap_handle->version.flags & STLINK_F_HAS_DPBANKSEL))
+ if (reg & 0x000000F0) {
+ LOG_ERROR("Banked DP registers not supported in current STLink FW");
+ return ERROR_COMMAND_NOTFOUND;
+ }
+
+ retval = stlink_dap_check_reconnect(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
+ data = data ? : &dummy;
+ if (stlink_dap_handle->version.flags & STLINK_F_QUIRK_JTAG_DP_READ
+ && stlink_dap_handle->transport == HL_TRANSPORT_JTAG) {
+ /* Quirk required in JTAG. Read RDBUFF to get the data */
+ retval = stlink_read_dap_register(stlink_dap_handle,
+ STLINK_DEBUG_PORT_ACCESS, reg, &dummy);
+ if (retval == ERROR_OK)
+ retval = stlink_read_dap_register(stlink_dap_handle,
+ STLINK_DEBUG_PORT_ACCESS, DP_RDBUFF, data);
+ } else {
+ retval = stlink_read_dap_register(stlink_dap_handle,
+ STLINK_DEBUG_PORT_ACCESS, reg, data);
+ }
+
+ return stlink_dap_record_error(retval);
+}
+
+/** */
+static int stlink_dap_op_queue_dp_write(struct adiv5_dap *dap, unsigned reg,
+ uint32_t data)
+{
+ int retval;
+
+ if (!(stlink_dap_handle->version.flags & STLINK_F_HAS_DPBANKSEL))
+ if (reg & 0x000000F0) {
+ LOG_ERROR("Banked DP registers not supported in current STLink FW");
+ return ERROR_COMMAND_NOTFOUND;
+ }
+
+ if (reg == DP_SELECT && (data & DP_SELECT_DPBANK) != 0) {
+ /* ignored if STLINK_F_HAS_DPBANKSEL, not properly managed otherwise */
+ LOG_DEBUG("Ignoring DPBANKSEL while write SELECT");
+ data &= ~DP_SELECT_DPBANK;
+ }
+
+ retval = stlink_dap_check_reconnect(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
+ /* ST-Link does not like that we set CORUNDETECT */
+ if (reg == DP_CTRL_STAT)
+ data &= ~CORUNDETECT;
+
+ retval = stlink_write_dap_register(stlink_dap_handle,
+ STLINK_DEBUG_PORT_ACCESS, reg, data);
+ return stlink_dap_record_error(retval);
+}
+
+/** */
+static int stlink_dap_op_queue_ap_read(struct adiv5_ap *ap, unsigned reg,
+ uint32_t *data)
+{
+ struct adiv5_dap *dap = ap->dap;
+ uint32_t dummy;
+ int retval;
+
+ retval = stlink_dap_check_reconnect(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
+ if (reg != AP_REG_IDR) {
+ retval = stlink_dap_open_ap(ap->ap_num);
+ if (retval != ERROR_OK)
+ return retval;
+ }
+ data = data ? : &dummy;
+ retval = stlink_read_dap_register(stlink_dap_handle, ap->ap_num, reg,
+ data);
+ dap->stlink_flush_ap_write = false;
+ return stlink_dap_record_error(retval);
+}
+
+/** */
+static int stlink_dap_op_queue_ap_write(struct adiv5_ap *ap, unsigned reg,
+ uint32_t data)
+{
+ struct adiv5_dap *dap = ap->dap;
+ int retval;
+
+ retval = stlink_dap_check_reconnect(dap);
+ if (retval != ERROR_OK)
+ return retval;
+
+ retval = stlink_dap_open_ap(ap->ap_num);
+ if (retval != ERROR_OK)
+ return retval;
+
+ retval = stlink_write_dap_register(stlink_dap_handle, ap->ap_num, reg,
+ data);
+ dap->stlink_flush_ap_write = true;
+ return stlink_dap_record_error(retval);
+}
+
+/** */
+static int stlink_dap_op_queue_ap_abort(struct adiv5_dap *dap, uint8_t *ack)
+{
+ LOG_WARNING("stlink_dap_op_queue_ap_abort()");
+ return ERROR_OK;
+}
+
+/** */
+static int stlink_dap_op_run(struct adiv5_dap *dap)
+{
+ uint32_t ctrlstat, pwrmask;
+ int retval, saved_retval;
+
+ /* Here no LOG_DEBUG. This is called continuously! */
+
+ /*
+ * ST-Link returns immediately after a DAP write, without waiting for it
+ * to complete.
+ * Run a dummy read to DP_RDBUFF, as suggested in
+ * http://infocenter.arm.com/help/topic/com.arm.doc.faqs/ka16363.html
+ */
+ if (dap->stlink_flush_ap_write) {
+ dap->stlink_flush_ap_write = false;
+ retval = stlink_dap_op_queue_dp_read(dap, DP_RDBUFF, NULL);
+ if (retval != ERROR_OK) {
+ dap->do_reconnect = true;
+ return retval;
+ }
+ }
+
+ saved_retval = stlink_dap_get_and_clear_error();
+
+ retval = stlink_dap_op_queue_dp_read(dap, DP_CTRL_STAT, &ctrlstat);
+ if (retval != ERROR_OK) {
+ dap->do_reconnect = true;
+ return retval;
+ }
+ retval = stlink_dap_get_and_clear_error();
+ if (retval != ERROR_OK) {
+ LOG_ERROR("Fail reading CTRL/STAT register. Force reconnect");
+ dap->do_reconnect = true;
+ return retval;
+ }
+
+ if (ctrlstat & SSTICKYERR) {
+ if (stlink_dap_param.transport == HL_TRANSPORT_JTAG)
+ retval = stlink_dap_op_queue_dp_write(dap, DP_CTRL_STAT,
+ ctrlstat & (dap->dp_ctrl_stat | SSTICKYERR));
+ else
+ retval = stlink_dap_op_queue_dp_write(dap, DP_ABORT, STKERRCLR);
+ if (retval != ERROR_OK) {
+ dap->do_reconnect = true;
+ return retval;
+ }
+ retval = stlink_dap_get_and_clear_error();
+ if (retval != ERROR_OK) {
+ dap->do_reconnect = true;
+ return retval;
+ }
+ }
+
+ /* check for power lost */
+ pwrmask = dap->dp_ctrl_stat & (CDBGPWRUPREQ | CSYSPWRUPREQ);
+ if ((ctrlstat & pwrmask) != pwrmask)
+ dap->do_reconnect = true;
+
+ return saved_retval;
+}
+
+/** */
+static void stlink_dap_op_quit(struct adiv5_dap *dap)
+{
+ int retval;
+
+ retval = stlink_dap_closeall_ap();
+ if (retval != ERROR_OK)
+ LOG_ERROR("Error closing APs");
+}
+
+static int stlink_dap_config_trace(bool enabled,
+ enum tpiu_pin_protocol pin_protocol, uint32_t port_size,
+ unsigned int *trace_freq, unsigned int traceclkin_freq,
+ uint16_t *prescaler)
+{
+ return stlink_config_trace(stlink_dap_handle, enabled, pin_protocol,
+ port_size, trace_freq, traceclkin_freq,
+ prescaler);
+}
+
+static int stlink_dap_trace_read(uint8_t *buf, size_t *size)
+{
+ return stlink_usb_trace_read(stlink_dap_handle, buf, size);
+}
+
+/** */
+COMMAND_HANDLER(stlink_dap_serial_command)
+{
+ LOG_DEBUG("stlink_dap_serial_command");
+
+ if (CMD_ARGC != 1) {
+ LOG_ERROR("Expected exactly one argument for \"st-link serial <serial-number>\".");
+ return ERROR_COMMAND_SYNTAX_ERROR;
+ }
+
+ if (stlink_dap_param.serial) {
+ LOG_WARNING("Command \"st-link serial\" already used. Replacing previous value");
+ free((void *)stlink_dap_param.serial);
+ }
+
+ stlink_dap_param.serial = strdup(CMD_ARGV[0]);
+ return ERROR_OK;
+}
+
+/** */
+COMMAND_HANDLER(stlink_dap_vid_pid)
+{
+ unsigned int i, max_usb_ids = HLA_MAX_USB_IDS;
+
+ if (CMD_ARGC > max_usb_ids * 2) {
+ LOG_WARNING("ignoring extra IDs in vid_pid "
+ "(maximum is %d pairs)", max_usb_ids);
+ CMD_ARGC = max_usb_ids * 2;
+ }
+ if (CMD_ARGC < 2 || (CMD_ARGC & 1)) {
+ LOG_WARNING("incomplete vid_pid configuration directive");
+ return ERROR_COMMAND_SYNTAX_ERROR;
+ }
+ for (i = 0; i < CMD_ARGC; i += 2) {
+ COMMAND_PARSE_NUMBER(u16, CMD_ARGV[i], stlink_dap_param.vid[i / 2]);
+ COMMAND_PARSE_NUMBER(u16, CMD_ARGV[i + 1], stlink_dap_param.pid[i / 2]);
+ }
+
+ /* null termination */
+ stlink_dap_param.vid[i / 2] = stlink_dap_param.pid[i / 2] = 0;
+
+ return ERROR_OK;
+}
+
+/** */
+static const struct command_registration stlink_dap_subcommand_handlers[] = {
+ {
+ .name = "serial",
+ .handler = stlink_dap_serial_command,
+ .mode = COMMAND_CONFIG,
+ .help = "set the serial number of the adapter",
+ .usage = "<serial_number>",
+ },
+ {
+ .name = "vid_pid",
+ .handler = stlink_dap_vid_pid,
+ .mode = COMMAND_CONFIG,
+ .help = "USB VID and PID of the adapter",
+ .usage = "(vid pid)+",
+ },
+ COMMAND_REGISTRATION_DONE
+};
+
+/** */
+static const struct command_registration stlink_dap_command_handlers[] = {
+ {
+ .name = "st-link",
+ .mode = COMMAND_ANY,
+ .help = "perform st-link management",
+ .chain = stlink_dap_subcommand_handlers,
+ .usage = "",
+ },
+ COMMAND_REGISTRATION_DONE
+};
+
+/** */
+static int stlink_dap_init(void)
+{
+ enum reset_types jtag_reset_config = jtag_get_reset_config();
+ int retval;
+
+ LOG_DEBUG("stlink_dap_init()");
+
+ if (jtag_reset_config & RESET_CNCT_UNDER_SRST) {
+ if (jtag_reset_config & RESET_SRST_NO_GATING)
+ stlink_dap_param.connect_under_reset = true;
+ else
+ LOG_WARNING("\'srst_nogate\' reset_config option is required");
+ }
+
+ if (transport_is_dapdirect_swd())
+ stlink_dap_param.transport = HL_TRANSPORT_SWD;
+ else if (transport_is_dapdirect_jtag())
+ stlink_dap_param.transport = HL_TRANSPORT_JTAG;
+ else {
+ LOG_ERROR("Unsupported transport");
+ return ERROR_FAIL;
+ }
+
+ retval = stlink_usb_open(&stlink_dap_param, (void **)&stlink_dap_handle);
+ if (retval != ERROR_OK)
+ return retval;
+
+ if (!(stlink_dap_handle->version.flags & STLINK_F_HAS_DAP_REG)) {
+ LOG_ERROR("ST-Link version does not support DAP direct transport");
+ return ERROR_FAIL;
+ }
+ return ERROR_OK;
+}
+
+/** */
+static int stlink_dap_quit(void)
+{
+ LOG_DEBUG("stlink_dap_quit()");
+
+ free((void *)stlink_dap_param.serial);
+ stlink_dap_param.serial = NULL;
+
+ return stlink_usb_close(stlink_dap_handle);
+}
+
+/** */
+static int stlink_dap_reset(int req_trst, int req_srst)
+{
+ LOG_DEBUG("stlink_dap_reset(%d)", req_srst);
+ return stlink_usb_assert_srst(stlink_dap_handle,
+ req_srst ? STLINK_DEBUG_APIV2_DRIVE_NRST_LOW
+ : STLINK_DEBUG_APIV2_DRIVE_NRST_HIGH);
+}
+
+/** */
+static int stlink_dap_speed(int speed)
+{
+ if (speed == 0) {
+ LOG_ERROR("RTCK not supported. Set nonzero adapter_khz.");
+ return ERROR_JTAG_NOT_IMPLEMENTED;
+ }
+
+ stlink_dap_param.initial_interface_speed = speed;
+ stlink_speed(stlink_dap_handle, speed, false);
+ return ERROR_OK;
+}
+
+/** */
+static int stlink_dap_khz(int khz, int *jtag_speed)
+{
+ *jtag_speed = khz;
+ return ERROR_OK;
+}
+
+/** */
+static int stlink_dap_speed_div(int speed, int *khz)
+{
+ *khz = speed;
+ return ERROR_OK;
+}
+
+static const struct dap_ops stlink_dap_ops = {
+ .connect = stlink_dap_op_connect,
+ .send_sequence = stlink_dap_op_send_sequence,
+ .queue_dp_read = stlink_dap_op_queue_dp_read,
+ .queue_dp_write = stlink_dap_op_queue_dp_write,
+ .queue_ap_read = stlink_dap_op_queue_ap_read,
+ .queue_ap_write = stlink_dap_op_queue_ap_write,
+ .queue_ap_abort = stlink_dap_op_queue_ap_abort,
+ .run = stlink_dap_op_run,
+ .sync = NULL, /* optional */
+ .quit = stlink_dap_op_quit, /* optional */
+};
+
+static const char *const stlink_dap_transport[] = { "dapdirect_jtag", "dapdirect_swd", NULL };
+
+struct adapter_driver stlink_dap_adapter_driver = {
+ .name = "st-link",
+ .transports = stlink_dap_transport,
+ .commands = stlink_dap_command_handlers,
+
+ .init = stlink_dap_init,
+ .quit = stlink_dap_quit,
+ .reset = stlink_dap_reset,
+ .speed = stlink_dap_speed,
+ .khz = stlink_dap_khz,
+ .speed_div = stlink_dap_speed_div,
+ .config_trace = stlink_dap_config_trace,
+ .poll_trace = stlink_dap_trace_read,
+
+ .dap_jtag_ops = &stlink_dap_ops,
+ .dap_swd_ops = &stlink_dap_ops,
+};
Code Review / openocd.git / blobdiff