return retval;
if (stm32x_erase_options(bank) != ERROR_OK) {
- command_print(CMD_CTX, "stm32x failed to erase options");
+ command_print(CMD, "stm32x failed to erase options");
return ERROR_OK;
}
stm32x_info->option_bytes.rdp = 0;
if (stm32x_write_options(bank) != ERROR_OK) {
- command_print(CMD_CTX, "stm32x failed to lock device");
+ command_print(CMD, "stm32x failed to lock device");
return ERROR_OK;
}
- command_print(CMD_CTX, "stm32x locked");
+ command_print(CMD, "stm32x locked");
return ERROR_OK;
}
return retval;
if (stm32x_erase_options(bank) != ERROR_OK) {
- command_print(CMD_CTX, "stm32x failed to erase options");
+ command_print(CMD, "stm32x failed to erase options");
return ERROR_OK;
}
if (stm32x_write_options(bank) != ERROR_OK) {
- command_print(CMD_CTX, "stm32x failed to unlock device");
+ command_print(CMD, "stm32x failed to unlock device");
return ERROR_OK;
}
- command_print(CMD_CTX, "stm32x unlocked.\n"
+ command_print(CMD, "stm32x unlocked.\n"
"INFO: a reset or power cycle is required "
"for the new settings to take effect.");
return retval;
if (optionbyte & (1 << OPT_ERROR))
- command_print(CMD_CTX, "option byte complement error");
+ command_print(CMD, "option byte complement error");
- command_print(CMD_CTX, "option byte register = 0x%" PRIx32 "", optionbyte);
- command_print(CMD_CTX, "write protection register = 0x%" PRIx32 "", protection);
+ command_print(CMD, "option byte register = 0x%" PRIx32 "", optionbyte);
+ command_print(CMD, "write protection register = 0x%" PRIx32 "", protection);
- command_print(CMD_CTX, "read protection: %s",
+ command_print(CMD, "read protection: %s",
(optionbyte & (1 << OPT_READOUT)) ? "on" : "off");
/* user option bytes are offset depending on variant */
optionbyte >>= stm32x_info->option_offset;
- command_print(CMD_CTX, "watchdog: %sware",
+ command_print(CMD, "watchdog: %sware",
(optionbyte & (1 << OPT_RDWDGSW)) ? "soft" : "hard");
- command_print(CMD_CTX, "stop mode: %sreset generated upon entry",
+ command_print(CMD, "stop mode: %sreset generated upon entry",
(optionbyte & (1 << OPT_RDRSTSTOP)) ? "no " : "");
- command_print(CMD_CTX, "standby mode: %sreset generated upon entry",
+ command_print(CMD, "standby mode: %sreset generated upon entry",
(optionbyte & (1 << OPT_RDRSTSTDBY)) ? "no " : "");
if (stm32x_info->has_dual_banks)
- command_print(CMD_CTX, "boot: bank %d", (optionbyte & (1 << OPT_BFB2)) ? 0 : 1);
+ command_print(CMD, "boot: bank %d", (optionbyte & (1 << OPT_BFB2)) ? 0 : 1);
- command_print(CMD_CTX, "user data = 0x%02" PRIx16 "", user_data);
+ command_print(CMD, "user data = 0x%02" PRIx16 "", user_data);
return ERROR_OK;
}
}
if (stm32x_erase_options(bank) != ERROR_OK) {
- command_print(CMD_CTX, "stm32x failed to erase options");
+ command_print(CMD, "stm32x failed to erase options");
return ERROR_OK;
}
stm32x_info->option_bytes.data = useropt;
if (stm32x_write_options(bank) != ERROR_OK) {
- command_print(CMD_CTX, "stm32x failed to write options");
+ command_print(CMD, "stm32x failed to write options");
return ERROR_OK;
}
- command_print(CMD_CTX, "stm32x write options complete.\n"
+ command_print(CMD, "stm32x write options complete.\n"
"INFO: %spower cycle is required "
"for the new settings to take effect.",
stm32x_info->can_load_options
for (i = 0; i < bank->num_sectors; i++)
bank->sectors[i].is_erased = 1;
- command_print(CMD_CTX, "stm32x mass erase complete");
+ command_print(CMD, "stm32x mass erase complete");
} else
- command_print(CMD_CTX, "stm32x mass erase failed");
+ command_print(CMD, "stm32x mass erase failed");
return retval;
}